Question about Cars & Trucks

1 Answer

How do i get my cherokee running?

I changed the crank sensor. Still no fire, turns over & I Sprayedstaring fluid straight into the intake. Changed ECM, I'm thinking may be the main computer now. Idk

Posted by on

Ad

1 Answer

The ECM is the main computer & they seldom fail,
unless you took it out doing some testing that caused
it to fail.

Did you check fuel pressure at the motor?
Did you check for spark using the proper tools to do so?
Do you have injector pulse?
Is the MAF hooked up?
Do you have a good working ignition switch & all
those circuits going where they should

Need a wiring diagram at some point to pick a test point

The ECM you changed, did it need to be programmed first
on a bench or after now in the vehicle?

Is the flywheel broken & do you have number one cylinder
recognition with the new cps or whatever that sensor is
attracted to?

Posted on Mar 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 dodge grand caravan turns over but won't start changed alternater and battery was good turns over and acts like it wants to start but don't


Probably gas or spark related. Check for both. A quick check of a gas problem is to spray starting fluid into the air intake and see if the engine fires and runs for a few seconds. then you know it is a fueling problem-either the pump has failed, the filter is clogged, or the injector circuit is not working.

If the fluid does nothing, then you need to check for spark on a plug wire while someone cranks the engine over- no spark means the ignition system is not working- check ignition coils, Ignition coil control module (ICM), crank and cam position sensors, -those are the major parts of the ignition system, all controlled by the pcm.

Jan 02, 2018 | Dodge Cars & Trucks

1 Answer

My Ford turbo 7.3 diesel will crank with started fluid but not with out? Alford,FL


Are the preheaters working,(glow plugs,intake air heater,depends on year of diesel)

May 05, 2017 | Cars & Trucks

1 Answer

1996 jeep grand cherokee 5.2. Sometimes will stall at red light. Turn off ignition and fires right back up. Also, misses when going up a hill. almost as if the power is being shut off. A FEW MISSES AND...


Mine too.same year and make. O2 sensors changed,crank sensor changed,,"No Help. Had to 3 garages and Jeep service NO HELP just a lighter wallet. Bill

Aug 30, 2013 | 1996 Jeep Grand Cherokee

1 Answer

Just changed Intake Manifold, now Crown Vic won't start


first check if there is fuel coming through then check your nock sensor which is on the crank pully then *** back 2 me

Oct 23, 2012 | 1997 Ford Crown Victoria

1 Answer

1987 jeep cherokee 4.0 Starting Issue engine cranks over but won't start- will start and run if primed. Will restart ok but if left setting will not start again. Changed: Fuel Pump Fuel Pump...


Check your temp sensor. if it's out of range it could be sending incorrect readings to the computer. Also check the white ceramic block on the drivers side fender back near the brake cylinder. It is a resistor that affects pump pressure on start up.

Mar 23, 2011 | 1987 Jeep Cherokee

2 Answers

97 jeep grand cherokee is not getting spark at the ignition coil I think its the PCM


Have your crank sensor checked. It won't send a signal to fire the coil if the crank sensor is bad.

Jan 13, 2011 | 1997 Jeep Grand Cherokee

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

2 Answers

94 Cherokee wont start


you need to see if your getting spark to the spark plugs, very possible you have a bad crank sensor

Jul 03, 2009 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15314 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...