Question about 2005 Nissan Pathfinder

1 Answer

Adjust bands How do you tighten the transmission bands.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 201 Answers

Procedure is listed in the Haynes manuel for that truck.

Posted on Mar 20, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NEED IT FOR BAND ADJUSTMENT ON A 05 NISSAN MAXIMA


Get a crowbar and move the altnator tighten the belt then tighten the alt back down

May 20, 2015 | 2005 Nissan Maxima SE

1 Answer

Automatic transmission service adjustments for 2000 mazda bravo


There should not need to be any "adjustments" for a normal fluid and filter service for your vehicle, unless you have replaced some parts of your transmission that requires adjustment such as the gearshift lever, intermediate and overdrive band, throttle cable, or transmission range sensor/switch.

With that said, the band adjustment specs are "Tighten the band adjusting screw to 10 Ft.Lbs. (14 N.m.) then back off 2 full turns. While holding band adjusting scew stationary, tighten the locking nut to 35-45 Ft.Lbs. (48-61 N.m.)

Jun 16, 2012 | Cars & Trucks

1 Answer

87 cutlass no reverse


foward and no reverse.In order for the reverse to happen there is a transmission brake assemble,the transmission band holds the brake assembly thus allowing fluid to be driven according to gear selection, when no reverse happens there is a malfunction of mechanical or hydraulic part, Depending on the condition you can adjust the kick down or adjust the band. A general procedure for automatic transmission band adjustment involves tightening the band adjusting screw to a given torque sequence, back off the adjusting screw from turning while torque-tightening the adjustment screw about a 1/4 turn and lock down the lock nut,and recheck to see if reverse has been restored.

Apr 23, 2011 | 1987 Oldsmobile Cutlass Supreme

1 Answer

What are the transmission band adjustment for a 1995 v6 3.0 dodge caravan


The proper fluid for that Tranamiaaion is Mopar ATF Plus 3 Type 7176. I recommend using it as I have found it does make a difference.

LOW-REVERSE BAND:
  1. Loosen, then back off lock-nut approximately five turns.
  2. Tighten adjusting screw to 41 in.lb.
  3. Back adjusting screw off 3½ turns, then tighten lock-nut to specifications
KICK DOWN BAND
The kick down band adjusting screw is located on the left side, top front of the trans-axle case.
  1. Loosen lock-nut and back off nut approximately five turns. Ensure adjusting screw turns freely in the trans-axle case.
  2. Using tool No. C-3880-A and adapter tool No. C-3705 , or equivalents, tighten band adjusting screw to72 in.lb.
  3. Back adjusting screw off 2¼ turns, then holding screw in position, tighten lock-nut to specifications.
Good luck and keep me posted, be glad to answer any other questions you may have.




Nov 16, 2009 | 1995 Dodge Caravan

1 Answer

Automatic transmission adjustment


It could easily be much more than tightening the bands. The transmission may have to be rebuilt. Tell the seller to go ahead and have the bands tightened and show you the bill, and that you will pay it if it is only tightening bands. Bet he will not do that.

Sirwriter

May 24, 2009 | 1986 Isuzu Impulse

2 Answers

Automatic transmission band adjustment


Don't have specs on band but the rule is that it should be close enough to the drum to engage without slamming, and loose enough to permit drum to turn without band dragging on it. Biggest problem I've seen people have when adjusting is that adjustment tightens down while turning lock nut. To avoid this, I usually adjust a bit looser than final adjustment so it tightens to correct position instead of becoming too tight. Don't drive 'till you have it right or you will burn band surface. When engaged in reverse, band should be applied and cannot drag. If you adjusted another band, check that one for improper adjustment.

May 10, 2009 | 1997 Jeep Wrangler

2 Answers

46RH transmission, no second gear.


Does it shift into 3rd at the right speed? If 2nd is just missing, try adjusting the kickdown band. (front band). The adjustment screw is on the outside of the case.

Apr 24, 2009 | 1999 Dodge Ram

1 Answer

Transmission slips or doesn't engage in reverse


Service the transmission, when you have the pan off, adjust the rear band. Loosen the lock nut. Tighten the adjuster to 10 ftlbs. Loosen the adjuster 2 turns and tighten the locknut. You either have an model 500 transmission (6 cylinder engine) or model 518 (V8 engine). In both transmissions reverse is controlled exactly the same. If adjusting the band doesn't fix it, then it will need rebuilt.

Mar 26, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Where are bands located on 1996 jeep cherokee transmission and can they be tightened?


THE BANDS ARE LOCATED INSIDE YOUR TRANSMISSION AND THE CAN BE ADJUSTED. HOWEVER THIS CAN ONLY BE DONE WITH THE TRANSMISSION OUT OF THIS VEHICLE. GOOD LUCK.

Dec 30, 2008 | 1996 Jeep Cherokee Country

1 Answer

Jeep grand cherokee revs for to high before changing gear


Message:
My 2002 Dakota has been somewhat confused about shifting as well. It showed a code P1762. I dropped the pan to install a new fluid filter and fluid-(use only ATF+3 or ATF+4). Since the pan was off I decided to adjust the bands. The front band controls the 2nd gear cluster. The rear band controls the 3rd gear cluster and reverse. For a 2-3 shift, the transmission shifts back to 1st gear with the front band while the rear band engages 3rd gear. If the front band does not release the 2nd gear clutches before the third gear clutches engage, the transmission binds, which shortens the life of the transmission clutches. If the front band releases too early in the shift, the engine will overspeed (sounds and feels like a slip) during the 2-3 shift.
The front band adjusting screw is on the driver's side above the shift linkage. The rear band is inside the fluid pan near the filter.
1. Loosen band adjusting screw locknut. Then back locknut off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw
threads if necessary. The front band adjuster is on the outside of the transmission and the locknut requires a 3/4" wrench.

2. Using Inch Pound Torque Wrench C-3380-A, a 3-in. extension and appropriate Torx� socket (T-40), tighten adjusting screw to 72 in-lb. CAUTION: If Adapter C-3705 (from SPX Miller) is needed to reach the adjusting screw, tighten the screw to only 47-50 in. lbs. torque.

3. Back off adjusting screw the number of turns listed below for your transmission.

4. Hold adjusting screw in place and tighten lock-nut to:

41 N�m (30 ft. lbs.) for the front band
34 N�m (25 ft. lbs.) for the rear band
The adjustment screw inside the case is a square head bolt. You will need a 1/4 square head socket to fit your torque wrench.
Band adjustments for each model year:
1994

* Front Band - tighten to 72 in-lb, back off 2-1/2 turns (all transmissions)
* Rear Band
o 32/42RH - Tighten to 72 in-LB, back off 4 turns
o 36/37/46/47RH - Tighten to 72 in-lb, back off 2 turns

1995-1996

* Front Band
o 42RH - tighten to 72 in-lb, back off 2-1/4 turns
o 46RH - tighten to 72 in-lb, back off 2-7/8 turns
o 47RH - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE/RH - tighten to 72 in-lb, back off 4 turns
o 46RE/RH - tighten to 72 in-lb, back off 2 turns
o 47RE/RH - tighten to 72 in-lb, back off 3 turns

1997-1998

* Front Band
o 42RE - tighten to 72 in-lb, back off 3-5/8 turns
o 46RE - tighten to 72 in-lb, back off 2-7/8 turns
o 47RE - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE - tighten to 72 in-lb, back off 4 turns
o 46RE - tighten to 72 in-lb, back off 2 turns
o 47RE - tighten to 72 in-lb, back off 3 turns

1999

* Front Band
o 42RE - tighten to 72 in-lb, back off 3 turns. (TSB 21-16-98)
o 47RE - tighten band adj. screw to 72 inch pounds, back off 1 7/8 turns
* Rear Band
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns
+ The 47RH rear band requires a 1/4" hex driver, the front band requires a
T-30 Torx driver, the filter is held in place by two screws which require a T-20 Torx drive

2000-2002

* Front Band
o 42RE - Tighten band adj. screw to 72 in-lb, back off 3 turns
o 44RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
o 46RE - Tighten band adj. screw to 72 in-lb, back off 2 7/8 turns
o 47RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
From Bill Konolday's 47RE notes: I usually go a little looser than factory
specs on this front band - backing off the adjustment screw 2 or 2 1/4 turns.
Depending on the circumstances I have backed off the band up to 2 1/2 turns.
* Rear Band
o 42RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 44RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 46RE - tighten band adj. screw to 72 inch pounds, back off 2 turns
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2003

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 1-3/4 turns
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2005

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds,
back off front band adjusting screw 1-3/4 turns for diesel vehicles,
or 1-1/2 turns, for V-10 vehicles.
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

94+ Automatic Transmission Bolt and Nut Torque Specs

* Front band adjustment locknut - 30 ft-lb
* Rear band adjustment locknut - 25 ft-lb
* Transmission pan bolts - 13 ft-lb
I just replaced the solenoid with the recommended transducer and all is fine now. The transducer cost me about $50 at a nearby dealership.
Hope this helps. -zman. rroszman@yahoo.com

Dec 09, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
2005 Nissan Pathfinder Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...