Question about 1996 Mitsubishi Eclipse

1 Answer

Just had clutch kit put in and new transmission and now the trow ot bearing is shot all the ones they say fit my car doesn't I have no idea what to do and the shop it's at ty can't figure it outeither

The Throw Out Bearing they say is for my car isn't the right one does anyone know why that might be car was driving fine till transmission went out and put another one in.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 660 Answers

Someone must have done a transmission swap in the past.
Have an auto parts store cross match the numbers you find on the transmission....see what it came from.

Posted on Mar 19, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bunnydawg
  • 5158 Answers

SOURCE: change front wheel bearing

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006f5b5

this is a pretty good guide on bearing replacement for your car

Please take a moment to rate this solution

Posted on Feb 02, 2009

  • 19 Answers

SOURCE: clutch removal

You have to insert a screwdriver through a hole in the bottom of the transmission. while pushing the fork away from the engine you push the retainer clip with the screwdriver blade. it should release the bearing and cause the cluch fork to move freely toward the engine. It may take you a few tries to do this. This is whats known as an reverse pressure plate assembly. I think its kinda stupid idea. If only the designers would look at what it takes to work on these things......m2242202_00014.png

Posted on May 26, 2009

  • 59 Answers

SOURCE: My release fork shaft on my MItsubishi pickup Has

i had a throwout that was just a bit bigger than the oem one and that caused me the same problem,its something else to check too

Posted on Jul 04, 2009

  • 395 Answers

SOURCE: i need to adjust the clutch on a 1995 standard

You will need to turn the cable adjuster so there is only about 1/8 inch of free travel of the cable where it attaches to throw out fork before it starts to move the fork. Once the throw out bearing is achieving its full travel the clutch should release and enable gear selection.

Don't forget to rate this post !!

Posted on Oct 11, 2010

  • 456 Answers

SOURCE: my pajero manual transmission 4WD has a clanking

hi.
a transmission problem when hot, but ok when cold, would suggest that the oil in the gearbox is getting too thin when it heats up.

you say that the transmission has been pulled out but do you know if the oil was actually changed in it.
if the oil has not been changed, drain it and replace with the specified oil.
if it was changed recently, then i would consider using a thicker grade transmission oil instead.

changing gearbox oil, is normally a matter of removing the drain plug on the bottom to drain the old oil, and then refilling using the level plug on the side of the engine.

Posted on Apr 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Good day. When you pushed the clutch pedal in it makes a noise in the engin.


this indicates a faulty throw out bearing
could be dry or in the process of failing completely
A service tip here is
as the transmission has to be removed for the replacement bearing to be fitted , it is a good idea to invest in a clutch kit and throw out bearing simply because 50% of the cost is the labor to remove and replace the transmission and if the bearing is bad , the clutch and pressure plate will soon need replacing
do the job once --do it properly

Jan 02, 2016 | 2010 Kia Soul

1 Answer

How much for a transmission


price a new one from a dealer spares department. That will give you an idea of prices from wreckers , transmission repair shops and service exchange specialists. Best to get several quote for rebuilds as most boxes only need bearings and synchro kits or if automatic
bearings, seals bands and clutch packs.

Dec 04, 2014 | 1991 Mazda 323

2 Answers

N d21 1986 manual transmission will not shift while running but will shift when not running any ideas why


Internal Wear--- such as synchro rings

Suspect it has to come apart & gone thru

It is 28 years old

Jun 11, 2014 | 2000 Ford Contour

1 Answer

DYI Clutch change, now transmission won't fit with the new clutch kit??


While its seams you don't see where you have to make caution,
So Now !Put back fry-wheel back on crankshaft then just check two thinks ......Check 1: see clutch plate there is center gropes on it so Mach on gear shaft center gropes.(I mean just put clutch plate in to transmission shaft & check if it`s center gropes are same match) If yes then pull back clutch plat & then refit under pressure plate on fly-wheel. Now come to Check 2 ! Mow when you fit it you must do centering of clutch plat to fix on gear shaft, So How you can do ?
There is two ways 1 is you have same shaft designed road or wood piece which help to center it!
While 2 ways is take big screw driver & put in the hole & do centering by looking it where center come just tight pressure plat bolts to hold the center .
So when you did like this you ll fix transmission (gear box) easily in a mints ....Just simple like this.
So best of luck & if you have any problem just mail me tallnsmartman@yahoo.com......

Nov 25, 2013 | Cars & Trucks

1 Answer

1983 toyota sr5 pickup wont move when in gear, let off the clutch and it revs up


Your clutch is gone, the clutch disc is worn so much it won't hold.
Buy a clutch kit-includes a new clutch disc, a new or reconditioned clutch pressure plate, and a new clutch release bearing. These three parts will restore your clutch. They all fit together between the transmission and the engine. The transmission has to be removed to put in the new clutch package. The cost of the clutch kit is about $120-$140.

Sep 26, 2013 | Toyota Pickup Cars & Trucks

1 Answer

My car is a 5 speed. I can only get it in one gear which is 5th the other gears it wont move. Is it the clutch or the transmission the trow out bearing has been making a noise for a while


It is possible that the throwout (clutch release) bearing is worn. In addition, one of the arms on the pressure plate could be broken or bent. If your car has a hydraulic clutch, check the fluid level befrpoe deciding on any major repair.
Has the clutch been replaced before, and how many miles are on the vehicle?.

May 07, 2011 | 1997 Nissan Maxima

1 Answer

My transmission makes noise until I depress my clutch


sounds like the main shaft bearings within the gearbox itself. i would of said the release bearing but u already changed it. the main shaft doesnt spin with the clutch pedal pressed. check for oil leaks and check the oil level in the gearbox.

Jun 20, 2010 | 1993 Ford Mustang

1 Answer

92 honda accord transmission clutch replacements


The trow out bearing could be sticking on the shaft it slides on or the clutch pedal its self could be holding pressure on the bearing causing it to stay engaged all the time.Or another cause could be the trans being not aligned straight with the motor..Hope this helps you.Have a great day..

Apr 01, 2009 | 1992 Honda Accord

3 Answers

How do i put in a throwout bearing


You have to separate the trans and the motor in order t get to the trow out bearing.It rides on the center shaft in the middle of the transmission once you remove it..

Mar 31, 2009 | 1990 Geo Prizm

Not finding what you are looking for?
1996 Mitsubishi Eclipse Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...