Question about 1998 Lexus ES 300

1 Answer

Cannot seem to find where the upper mounting nuts are located in the vehicle. I have already removed the rear deck and still cannot seem to find how to drop the strut

Posted by on

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 365 Answers

Where...in the back? Lift up the trunk liner and remove or fold back, there should be some rubber/plastic oval-shaped plugs in the steel of the trunk floor...pry one up with a screwdriver being careful not to damage it too badly...thats where they are on a 2003 ES300

Posted on Jun 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change alternator 2005 chryler 300


This answer covers:
2005 Chrysler 300 6cyl VIN "G" 3.5L SFI HO (72% of 2005 300's)
2005 Chrysler 300 6cyl VIN "R" 2.7L MFI DOHC (28% of 2005 300's)
2005 Dodge Magnum 5.7L engine

Alternator

Removal & Installation


WARNING - Precautions Section:
Disconnect negative cable from battery before removing battery output wire (b+ wire) from alternator. Failure to do so can result in injury or damage to electrical system.

2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Disconnect alternator field circuit plug.
  5. Remove B+ terminal nut and wire.
  6. Remove 2 lower mounting bolts.
  7. Remove alternator.
To install:
  1. Install alternator.
  2. Install upper bolt mounting bolt.
  3. Install 2 lower mounting bolts.
  4. Tighten bolts to 48 ft. lbs. (65 Nm).
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Connect alternator field circuit plug.
  7. Install alternator drive belt.
  8. Connect negative battery cable.
3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Remove bracket bolts.
  5. Remove upper mounting bolt.
  6. Raise and support vehicle.
  7. Remove middle splash pan.
  8. Disconnect alternator field circuit plug.
  9. Remove B+ terminal nut and wire.
  10. Remove lower mounting bolts.
  11. Remove alternator.
To install:
  1. Install alternator.
  2. Install lower mounting bolts. Loosen install the upper mounting bolt.
  3. Tighten lower mounting bolts to 48 ft. lbs. (65 Nm).
  4. Connect alternator field circuit plug.
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Install middle splash pan.
  7. Lower vehicle.
  8. Remove loose installed upper bolt.
  9. Install bracket and bracket bolt.
  10. Install upper mounting bolt and bracket.
  11. Tighten upper mounting bolt to 48 ft. lbs. (65 Nm).
  12. Tighten the bracket bolt to 40 ft. lbs. (54 Nm).
  13. Install alternator drive belt.
  14. Connect negative battery cable.
5.7L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable at battery.
  3. Remove alternator drive belt.
  4. Raise and support vehicle.
  5. Unsnap plastic insulator cap from B+ output terminal.
  6. Remove B+ terminal mounting nut at rear of alternator. Disconnect terminal from alternator.
  7. Disconnect field wire connector at rear of alternator by pushing on connector tab.
  8. Remove alternator support bracket nut and bolt. Remove support bracket. See Figure 1.
  9. Remove 2 alternator mounting bolts. See Figure 2.
  10. Remove alternator from vehicle.

Fig. 1 Alternator Support Bracket - 5.7L engine

7309257c-afe6-4c17-9422-d7fa2e3bd4b1.jpg

Fig. 2 Alternator Mounting Bolts - 5.7L engine

22b81ff7-7912-467f-9eaf-13ba2ff3a1a4.jpg

Oct 13, 2014 | 2005 Chrysler 300

1 Answer

How to replace rear shocks


Removal & Installation

  1. Raise and safely support the vehicle.
  2. Support the rear axle and slightly lower the vehicle enough to lessen tension on the shock absorber.
  3. Remove the lower shock absorber retaining nut and washer.
  4. Disconnect the lower end of the shock absorber from the mounting stud.
  5. Remove the shock absorber upper end retaining nut and washer.
  6. Remove the shock absorber from the vehicle.
To install:
  1. Install the shock absorber onto the upper and lower mounting studs of the vehicle.
  2. Install the washers and retaining nuts. Tighten the upper and lower retaining nuts to 22-30 ft. lbs. (30-41 Nm) on 2001-02 models or 22 ft. lbs. (30 Nm) for the upper bolts and 47 ft. lbs. (64 Nm) on the lower bolts.
  3. Lower the vehicle.

Jul 07, 2014 | 2004 Nissan Quest

1 Answer

How do you replace shocks on 1991 buick skylark


REMOVAL & INSTALLATION Fig. 1: After you open the trunk lid, use a suitable prytool to remove the trim cover 86888036.jpg
Fig. 2: Some vehicles have a cover which must be removed to access the shock retaining nuts 86888037.jpg
Fig. 3: Unfasten the upper shock attaching nuts 86888038.jpg
  1. Disconnect the negative battery cable.
  2. Open the trunk lid and remove the trim cover. If equipped, remove the nut cover.
  3. Remove the upper shock attaching nut(s). If removing both shocks, remove one at a time.
  4. Raise and safely support the vehicle.
  5. Unfasten the lower shock absorber mounting bolts. One wrench will have to be placed on the bolt head side to retain the bolt as you loosen the nut. Usually a 15mm wrench is used to remove them. To install: Fig. 4: After the vehicle is raised and safely supported, use a socket to unfasten the lower retaining bolt 86888039.jpg
    Fig. 5: Remove the retaining bolt, then . . . 86888040.jpg
    Fig. 6: . . . remove the shock absorber assembly from the vehicle 86888041.jpg
  6. Connect the shock absorbers at the lower attachment and install the attaching bolt.
  7. Lower the vehicle enough to guide the shock absorber upper stud through the body opening, then fasten the upper shock absorber attaching nut loosely. Tighten the lower shock absorber mounting bolt to 35 ft. lbs. (47 Nm).
  8. Remove the axle support, then carefully lower the vehicle. Tighten the shock absorber upper nut to 21 ft. lbs. (29 Nm).
  9. If equipped, install the retaining nut cover, then install the rear trim cover. Close the trunk lid.
  10. Connect the negative battery cable.
prev.gif next.gif

Oct 08, 2010 | Buick Skylark Cars & Trucks

1 Answer

Need new struts on rear, Would like to replace with air shocks. Any suggestions on how I would do this?


Shock Absorber -The rear already has air shocks on the 1999 Cadillac Deville: REMOVAL & INSTALLATION Rear
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Rear wheel Fig. 1: Exploded view of the rear shock absorber mounting 9300vg06.gif

    • Negative battery cable
    • Shock absorber electrical connector from the rear suspension support, If equipped
  3. Support the lower control arm with a jack to relieve the tension on the shock absorber.
  4. Remove or disconnect the following:
    • Lower shock absorber mounting bolt and nut
    • Upper mounting nut, retainer, and insulator
    • Shock absorber compress by hand and remove through the upper control arm
    To install:
  5. Position the top of the shock absorber with the insulator attached into the suspension support.
  6. Install or connect the following:
    • Upper shock insulator, retainer and nut. Torque the nut to 55 ft. lbs. (74 Nm).
    • Shock absorber lower mounting nut/bolt. Torque the nut to 75 ft. lbs. (102 Nm).
    • Shock absorber electrical connector to the rear suspension support, if equipped
    • Rear wheel
    • Negative battery cable
prev.gif next.gif

Jul 29, 2010 | 1999 Cadillac DeVille

1 Answer

Do i have to remove the back seat to take rear struts off


Answer
REMOVAL - SHOCK ASSEMBLY
NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.

Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
Remove plastic cover from the top of the shock assembly.
Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
Raise vehicle on jackstands or centered on a frame contact type hoist. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE)
Remove the rear wheel and tire assembly from the vehicle.
Remove two fasteners holding the splash shield to the shock assembly upper mount.
Remove bolt attaching shock absorber to rear knuckle (Shock Absorber Attachment To Knuckle).
Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening

Nov 23, 2009 | 2002 Dodge Stratus

1 Answer

How do I change the rear shock on my 1999 Dodge Neon?


  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Unfasten the retainer(s), then remove the hydraulic flex hose bracket from the strut bracket. If equipped with ABS, the wheel speed sensor cable routing clip is also attached to the strut assembly bracket.
  1. Support the rear knuckle, suspension and brake components before removing the clevis bracket-to-knuckle attaching bolts. Do NOT allow the weight of the knuckle and related components hang without support when the strut is removed.


  2. WARNING The knuckle-to-strut attaching bolts are serrated and must not be turned during removal. Remove the nuts while holding the bolts stationary in the knuckle.
  1. Hold the bolt with a wrench, then unfasten the 2 clevis bracket nuts attaching the strut to the knuckle.
Fig. Fig. 2: Location of the knuckle-to-clevis bracket bolts


  1. Carefully lower the vehicle, then open the trunk. Access to the rear upper strut mount-to-strut tower attaching bolts is through the trunk of the car.
  2. If necessary, remove the carpet from the top of the strut tower. Then, remove the rubber dust shield from the top of the strut tower for easier access to the upper strut nuts.
  1. Loosen, but do not remove the 4 upper strut mounting nuts. Then, while supporting the strut assembly, fully remove the 4 strut mount attaching nuts.
  1. Remove the strut assembly from the knuckle by sliding the knuckle out of the clevis bracket on the strut, then remove it from the vehicle.
Carefully pull the strut assembly out of the vehicle
To install:
  1. Position the strut back into the vehicle with the 4 studs on the strut mount assembly through holes in the strut tower of the vehicle. Install the 4 strut mount-to-body attaching nuts onto the mount studs. Tighten the nuts to 25 ft. lbs. (34 Nm).
  2. Install the dust shield into the opening on top of the strut tower. Install the carpeting back on top of the rear strut tower.
  3. Raise and safely support the vehicle.
  4. Install the knuckle into the clevis bracket on the strut assembly. Install the 2 clevis bracket-to-knuckle attaching bolts and nuts. Hold the bolts with a wrench while tightening the nuts to 70 ft. lbs. (95 Nm).
  5. Install the brake hose bracket to the strut bracket and secure with the retaining bolts. If equipped with ABS, the wheel speed sensor cable routing clip is also attached to the strut bracket.
  6. Install the wheel and tire assembly on the vehicle. Tighten the lug nuts evenly, in sequence, to 100 ft. lbs. (135 Nm).
  7. Carefully lower the vehicle.
  8. Have the toe checked and adjusted as necessary.

Nov 05, 2009 | 1999 Dodge Neon

2 Answers

Whers is the starter on a 1996 saturn sl and what is the best way to replace it


Just is one way to replace. Review this:

1996 Saturn SL 1.9L MFI SOHC 4cyl

1fe174c.jpg

If the starter is to be replaced, remove the bracket from the old starter

REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If equipped, remove the starter shield pin by pulling on it with pliers, then lift and release the shield from the solenoid.
  4. Spray the solenoid electrical connection nuts and studs with penetrating oil, and allow it to seep in for a minute to loosen the connections. While the oil is soaking in, tag the solenoid electrical connectors for identification during assembly.
It is very important that the solenoid electrical connection nuts and studs are sprayed with penetrating oil prior to removal to avoid damage to the solenoid end cap. A cracked cap will allow debris and moisture to enter and corrode the solenoid contacts.
  1. Carefully loosen the bolts and detach the starter electrical connectors. Position the wires to the side and out of the way.
  2. Remove the lower starter mounting bolt.
  3. Using an obstruction wrench, remove the upper starter mounting bolt. If the upper starter mounting bolt cannot be reached from below the vehicle, it may be accessible from above, through the intake manifold support bracket opening.
  4. If equipped, remove the bolt attaching the starter rear support bracket to the vehicle. Rotate the starter until the bracket misses the axle shaft support bracket.
  5. Carefully support the starter, pulling it rearward and toward the left side of the vehicle to remove it.
To install:
  1. If equipped on the old starter, install the rear starter support bracket to the new starter. Tighten the bracket nuts to 7 ft. lbs. (9 Nm).
  2. Guide the starter into the bell housing and rotate the assembly until the lower bolt hole in the starter aligns.
  3. Verify that the bracket is properly aligned and loosely install the bracket bolt, then loosely install the starter mounting bolts. It may be necessary to raise or lower the vehicle for access to both the upper and lower bolts, but do not tighten any bolts until all of the mounting bolts have been started.
  4. Tighten both upper and lower starter assembly attachment bolts to 27 ft. lbs. (37 Nm).
  5. Reconnect the electrical wires and install the nuts. Be careful not to overtighten the nuts and crack the solenoid end cap. Route the wiring cable so it will not contact any rough surfaces. Tighten the starter positive terminal nut to 89 inch lbs. (10 Nm) and the solenoid terminal nut to 44 inch lbs. (5 Nm).
  6. If equipped, install the starter shield and push pin, being careful that the pin is positioned for possible future removal.
  7. Lower the vehicle.
  8. Connect the negative battery cable and verify operation.
15aebbb.jpg

Fig. Remove the starter motor dust shield retaining clip


75381aa.jpg
Fig. Lift off and remove the starter motor dust shield from beneath the vehicle


98d7fb8.jpg
Fig. Loosen the starter solenoid wiring terminal screws ...

f05fd78.jpg

Fig. ...then label and disengage the wiring harnesses from the starter solenoid, carefully positioning them out of the way


348d2a8.jpg
Fig. Loosen the lower starter motor mounting bolt ...


46ba7f0.jpg
Fig. ...then remove the bolt from the vehicle


08946b5.jpg
Fig. If accessibility is limited from below the vehicle, use the opening in the intake manifold support bracket to reach the upper starter bolt

3233aaf.jpg

Fig. Remove the rear mounting bracket bolt, then remove the starter from the vehicle




I hope help you with this (remember rated this help) Good luck.

Oct 16, 2009 | 1996 Saturn SL

1 Answer

Removal of rear shocks on 1991 pontiac sunbird se


open the trunk remove the trim panel to clear the upper shock mount nut.loosen wheel nuts raise rear of vehicle support on jack stands.support trailing arm.with a jack .remove the shock absorber mounting nut and bolt.then remove the upper two bolts at wheel well above the coil spring.do one wheel at a time becauses it will damage brake lines if you remove both shocks. besure to block the front wheels to keep car from moving.

Apr 12, 2009 | 1991 Pontiac Sunbird

1 Answer

97 Taras sedan SE style rear stut top bolt and nut location.


The top nuts are located from inside of the trunk. If you look behind the material that covers the wheel wells you should find the nuts near the top of the wheel wells.

Nov 30, 2008 | 1997 Ford Taurus

1 Answer

2004 dodge stratus SE


This is a dangerous job if you do not have the proper equipment for compressing the spring that is around the rear shock. I do not recomend performing this job without the proper equipment. Unloading the spring without it compressed can cuase injury.

If you have the proper equipment this is how you do it.

REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.
  1. Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
  2. Remove plastic cover from the top of the shock assembly.
  3. Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
  4. Raise vehicle on jackstands or centered on a frame contact type hoist.
  5. Remove the rear wheel and tire assembly from the vehicle.
  6. Remove two fasteners holding the splash shield to the shock assembly upper mount.
  7. Remove bolt attaching shock absorber to rear knuckle
  8. Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
  9. Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening.

Aug 04, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
1998 Lexus ES 300 Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...