Question about 2006 Ford Ranger

1 Answer

Fuel pump wont wort

Were is the inertia switch

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Ford Expert
  • 150 Answers

It is usually under the dash on the passenger side or behind the kick panel on the same side.

Posted on Dec 14, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: 2004 ford E350 no power to fuel pump

put a test light on the ground wire to a 12v power source and see if the pump is grounded properly

Posted on Sep 11, 2008

pippall
  • 1486 Answers

SOURCE: car cut off while driving wouldnt start back up

Replace the switch.Yes they can be faulty.If that doesn't solve the problem then your fuel pump is causing it to trip out.change the fuel pump.good luck.

Posted on Jun 29, 2009

  • 70 Answers

SOURCE: need to find fuel cutoff inertia switch in a 1996

it is locate under dash board. a little to the right of center it is about 3/4 inch by 1inch is proably red or orange with a push button on one side. push the button

Posted on Aug 06, 2009

  • 7353 Answers

SOURCE: where is the fuel pump relay and the reset switch

Relay is inside the ICM (Integrated Control Module) right ahead of the right shock tower. The inertia switch should be in the trunk, on the right side.

Posted on Nov 02, 2009

  • 100 Answers

SOURCE: e-150 fuel pump inertia switch location

on some fords it is on pass side kick panel you have to feel in a hole and you will feel a reset button,hope this helps

Posted on Feb 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 mercury marauder. Y wont the fuel pump kick on???


Could be that the Inertia switch has cut it off. Check Websites with the term "2004 mercury marauder inertia switch" then add location to the search if the first search only generates parts.

This is a safety device and is a part which cn be in different locations depending on the year.


In addition to the Inertia switch, a fuel pump relay or a crankshaft sensor can do the same thing.

May 08, 2015 | 2004 Mercury Marauder

1 Answer

Is the Inertia switch and the fuel pump relay the same thing?


No. The relay powers up the fuel pump and the inertia switch kills power to the fuel pump in the event of a collision to prevent a fuel related fire.

Mar 20, 2015 | Cars & Trucks

1 Answer

2010 nissan versa got in a collision. Wont crank over. Would the fuel inertia switch cause this?


Fuel inertia switch stops the fuel pump running in the case of a collision causing a broken fuel pipe which otherwise could spray a litre of petrol every few seconds and rather spoil someone's day.

Certainly a tripped inertia switch would prevent the engine from starting but I doubt it would stop the engine cranking, though I don't have up to date information on the model and there could be different safety regulations where you are.
The inertia switches are accessible and resettable so why not just reset it and try again. Your vehicle handbook will have the details.

An immobiliser stops the the engine cranking on some vehicles as well as stopping the spark and injection and often the fuel pump.
Bridging the battery positive wire to the solenoid to make the starter crank the engine won't be switching the rest of the stuff back on.

Feb 06, 2015 | 2010 Nissan Versa 1.8

1 Answer

WONT START AFTER LEFT T BONE COLLISION HAVE CUT SWITCH ON AND OFF TO RESERT FUEL PUMP GUAGE WONT WORK CANT FINE INERTIA SWITCH????


The inertia switch is usually found at passenger foot inside the foot panel, hope this helps

Sep 10, 2014 | Cars & Trucks

1 Answer

99 expedition my fuel pump isnt working checked fuses is there a fusuble fink with key on the fuel shutt off switch behind right kick panel has no power to any of the wires?


Power comes from a fuseable link to the pump relay, then to the inertia switch on the dark green and yellow wire. Power from the inertia switch to the pump is on the pink blue or pink black wire.

Jan 20, 2014 | 1999 Ford Expedition

1 Answer

1989 f-250 inertia fuel shut-off switch switch location


This should be in the owner's manual. I found the below on autozone.com, their repair help location:
An inertia switch is used as a safety device in the fuel system. The inertia switch is located in the cab, generally under the dashboard on the right side. It is designed to open the fuel pump power circuit in the event of a collision. The switch is reset by pushing each of 2 buttons on the switch simultaneously (some models use switches with only one reset button). The inertia switch should not be reset until the fuel system has been inspected for damage or leaks.
When the ignition switch is ON , it turns the EEC power relay ON . The EEC power relay provides power to the powertrain control module (PCM) and the control side of the fuel pump relay. Power for the fuel pump(s) is supplied through a fuse link or high current fuse attached to the starter solenoid (battery side). From the fuse link or high current fuse, current flows through the fuel pump relay and inertia switch to the fuel pump(s). The fuel pump relay is controlled by the PCM.
When the ignition switch is turned ON , the fuel pump(s) will operate. If the ignition switch is not turned to the START position the PCM will shut the fuel pump(s) OFF after 1 second. The PCM will operate the fuel pump(s) operate the fuel pump(s) when the ignition switch is turn to START position to provide fuel while cranking.
After the engine starts, the PCM will continue to operate the fuel pump(s) unless the engine stops, drops below 120 rpm or the inertia switch is tripped.

Dec 28, 2013 | 1989 Ford F 250

1 Answer

It got wrecked and i fix it but it wont start


Did you check for an inertia switch. Most vehicles have an inertia switch installed in the fuel pump circuit that cuts off the fuel pump when involved in an accident.

Nov 25, 2013 | 2005 Toyota Tundra SR5

1 Answer

I have a 2004 freestar that wont start.changed fuel pump still wont start.pump wont run!


Hello, If you have not checked your Inertia switch it shuts off the fuelpump and may need to be Reset. It should be in the RH side of the jack compartment. You just push and hold a button on the switch and then the fuelpump should work.

The Inertia switch is a safety device and can trigger when a door or hatch is closed hard enough to simulate a crash. You also can have a Relay in the Powerbox which may be labeled. Try the Inertia switch first and if it does not help, then change the Fuelpump Relay.

Feb 26, 2011 | 2004 Ford Freestar

1 Answer

1997 Ford F150 Electric Fuel Pump will npt pump


Did you check the fuel inertia switch in the passenger side kick panel ?

The fuel pump is powered :
the fuse to the fuel pump relay.
The fuel pump relay to the fuel inertia switch
The fuel inertia switch to the fuel pump itself.

At the fuel inertia switch in the kick panel, power from the relay is the Dark Green w/ Yellow stripe wire and the pink w/ black stripe wire is the power. from the fuel inertia switch to the fuel pump.

If you jumper the fuel pump relay, you should hear it run. If not pull the fuel pump relay, and check the pins in the relay socket, pin 30 should be the power from the fuse.

50b0c31.jpg

If you have power at pin #30, jumper the relay socket as shown with the red line above, and check the dark green w/ yellow stripe wire at the fuel inertia switch for power.
Press the button on the top of the fuel inertia switch, and check for power leaving the fuel inertia switch on the pink w/ black stripe wire.

This is tests good, check for power at the fuel pump, same pink w/ black stripe wire.
Fuel inertia switch info is in the owners manual, If you did not get an owners manual with your truck ( purchased used ), you can download one from Ford :
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

Jan 03, 2010 | 1997 Ford F150 Regular Cab

1 Answer

I have a 2003 Ford Ranger and just replaced inertia switch & relay and it still wont start. where is the fuse under the hood to do with the fuel?


Check the wire at the inertia switch with a test light,If there is not voltage check fuse #23 a 20amp fuse in the battery junction box located in the left rear of the engine compartment.If there is power at the inertia switch this is the last step before the fuel pump so suspect a bad pump or broken wire:)

Aug 28, 2009 | Ford Ranger Cars & Trucks

Not finding what you are looking for?
2006 Ford Ranger Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...