Question about Toyota Tercel

Open Question

Open door on 98 tercel lights blink and car beeps 30 times then stops then repeats until door is closed. Car won't start

Had to take battery out to replace headlight

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

beauman
  • 60 Answers

SOURCE: My car alarm is blinking

you can try switching the key to the "on" position then open the hood and disconnect the negative terminal of the battery and reconnect after 2minutes. this will allow the alarm to be '"reset" and will recognize that you have the key for the vehicle.

Posted on Aug 16, 2008

fknstart
  • 404 Answers

SOURCE: 2005 dodge durango anti-theft system

have you tried starting the car ,if not lock the car, open with key manually and try and start

Posted on Jan 05, 2009

SOURCE: Interior Lights and Door Ajar light stay w/beeping noise.

Try spraying WD-40 into the door latching mechanism (door side). I learned this fix after two battery replacements, but have only had to spray twice in the more than seven years of ownership

Posted on Jan 29, 2009

blueextc3221
  • 15935 Answers

SOURCE: 98 Dodge Durango no electrical power

When the armed Vehicle Theft Security System (VTSS) senses that the battery has been disconnected and reconnected, it enters its power-up mode. In the power-up mode the alarm system remains armed following a battery failure or disconnect. If the VTSS was armed prior to a battery disconnect or failure, the system will have to be actively or passively disarmed after the battery is reconnected. The alarm can be disarmed by locking the vehicle and turning the drivers door lock to the lock (arm) position. Wait a few minutes then unlock (disarm) the drivers door and the vehicle should start.
If the VTSS has been disabled in the high-line Central Timer Module (CTM), the VTSS feature must be re-enabled using the Chrysler DRB scan tool. The clicking you heard was probably from the CTM located behind the glove box.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Apr 28, 2009

  • 5501 Answers

SOURCE: theft light blinking/car won!t start

If you have key numbers on the door, you should enter the code, then immediately start the truck. If this does not work contact the dealer for a sequence to reset the alarm.

Posted on Jun 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jag 2002 x type remote key will not open close doors fitted new battery


try reprogramming it by sitting in with doors closed switch ignition on then off 5 or 6 6 times until a beep then press any button on remote to program you may have to repeat on spare keys

Jul 16, 2017 | Jaguar X-Type Cars & Trucks

1 Answer

Hazard lights flashing and alarm sounding. How do I stop these?


Every car brand and model has its procedure to stop the flashing light and alarm sounding.
But still the common procedure is Make sure boot and bonnet are closed properly.

It can also be a switch, but check your alarm by locking yourself inside the car, and then press the close button on the key 2 times repeatedly until the lock control on the door doesn't make anything. Then open the door by pushing the lever or open the hood . If the horn sounds and the lights blink your alarm is ok , if only the lights blink you should take it to dealer. You can stop the hazard lights and horn sound by pressing the unlock button on the key.

May 12, 2016 | Cars & Trucks

2 Answers

Security light blinks car won't start disconnected the battery used a different key still won't start


need to reprogram the security system. turn the key to start position then to run . let the key stay on until the light stops flashing. repeat these steps 3 times then the car should start if there is not a problem with the pass-lock sensor in the ignition switch or the BCM( body control module).

Aug 07, 2011 | 2004 Pontiac Grand Am

1 Answer

How do i reprogram the ignition after it has been changed on a 2002 grand prix?


  • disconect battery for 30 seconds, reconect.
  • try to start car, leaving key on for 10 minutes or untill security light stops blinking.
  • Turn key off

then try to start car. if this doesnt work repeat procedure.
Hope this helps

Nov 10, 2009 | 2000 Pontiac Grand Prix

2 Answers

98 chevy cavalier cranks but wont start changed fuel pump,computer,crank shaft position sensor and the theft system light is staying on


try to start the car, than the anti theift would shut the car off. you wait ten min with the key on, until you see the anti theift flash or disapear. than turn key to off position and try to start it. this will reprogram the computer.. Good luck.

you can also try disconnecting the battery for 30 minutes

Oct 07, 2009 | 1998 Chevrolet Cavalier

2 Answers

1996 pontiac grand prix won't start-security problem


hold the reset button on the fuse panel and when it blinks let off of it and it will go away

Aug 02, 2009 | 1996 Pontiac Grand Am

1 Answer

Door ajar light stays on after i close the door


I had the same problem in my 98 and 96 Sables. Ford dealer says it is a problem with a sensor, located behind the left rear quarter panel. It doesn't recognize when the doors are closed, therefore it leaves the dome light, etc. on--sometimes briefly, but possibly until the battery goes dead. Worse when the weather is damp. Their solution was to throw it on the diagnostic computer BUT ONLY WHILE THE PROBLEM IS ACTIVELY HAPPENING, then replace the sensor--they quoted me a minimum of $300. I leave the cover off the dome light, and pull the bulb when necessary.

Mar 15, 2009 | 1996 Mercury Sable

2 Answers

My car alarm is blinking but the remote doesn't work. I already replaced the battery to the remote so I know that's not the problem. If I open the car the alarm goes off and doesn't allow me to start the...


you can try switching the key to the "on" position then open the hood and disconnect the negative terminal of the battery and reconnect after 2minutes. this will allow the alarm to be '"reset" and will recognize that you have the key for the vehicle.

Aug 15, 2008 | 2003 Toyota Corolla

1 Answer

Beeping 04 mustang


i have same issue with my 01 does it when you first start the car and about 30 minutes after driving found online it is my airbag light in dash is blown havent changed it yet so im not sure

Jul 12, 2008 | 2004 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...