Question about 2004 Mazda 6

1 Answer

Headlight wont work due to wires

Car was in minor front end collision, has a yellow wire coming from back of headlight and looks like it should slide on a tooth somewhere, headlight doesn't work and im guessing this is why. any ideas as to where it should plug in?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 46,643 Answers

Check on the back of the bulb . There should be 3 wires on 3 pins If there is a spare pin then I would say that is where it is supposed to be.

Posted on Mar 19, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: car runs bad after replacing spark plugs and wires

Make sure the part store gave you the correct plugs and wires. Consult a third source for a firing order.

Posted on Jan 06, 2009

  • 14585 Answers

SOURCE: I have a 1995 mazda

On your year the 02 sensors did more for fuel economy. Of course this was a major part. But it did not affect the performance of the car. they would usually run rich and use more fuel. If the wire is from the 02 sensors the check engine light would be on. If you have the early 95 , OBD1, It is getting harder to find shops that can hook it up to a daignostic computer. Later is the OBD2. Most all shops can hook up. The loss in acceleration is probably the fuel filter. At low end you will get plenty of fuel. but at the higher speeds the filter is clogged and. will not let the fuel flow through like it should. You will have pressure , but not flow.. Other things could be the catalitic converter and air filter.

Posted on Jul 13, 2011

SOURCE: what is the correct matching color code for an aftermarket headlight socket?

Need a two wire socket

The colors you meter out with a volt meter- set to
the buzzer feature- to compare to the one your replacing

Posted on Dec 15, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 dodge ram wont start after a minor front end collision on drivers side headlidht turns over wont start acts like no fuel


Check the ASD (automatic shut down) relay it may have tripped, it is cheap try replacing it. It is located in the under hood junction box.

Jun 07, 2017 | Dodge Cars & Trucks

1 Answer

What should I check and/or reset on a '94 Camaro to get it to start after a minor collision which deployed the airbags?


If fuel pump issue, check the fuel pump relay. I wasn't sure of engine size, may not make a difference. Check the relay wiring circuits. The pink wire is voltage to load side of relay, fuse protected, goes hot with the key on. You can use a test lite to check for voltage. The control side of relay, left side, needs voltage and ground, that bottom wire is a chassis ground. That top wire is voltage, should be hot with engine cranking, comes from pcm. Hopefully that relay is located behind driver side kick panel, to the left of foot-well. If it isn't located in that area, then, I don't know?
camaro fuel pump-c1a1d50n0xvjplieoywey0oi-1-0.jpg

Mar 07, 2017 | Cars & Trucks

1 Answer

2004 Chevy venture horn not working after front end bumper to bumper collision (minor... sliding in snow..). Fuses or is it most likely the relay? And I been trying to locate the horns, no luck.


My info says to remove headlamp assembly to get at horn, either side. At horn connector, black wire is ground, the green wire is voltage.

Apr 15, 2016 | Cars & Trucks

2 Answers

Minor front end collision repaired,now taillights don't work,bulbs replaced


the parking lights in the back are not working? i would check for a pinched wire or bare wire on the front lights, did they replace the bulbs when they did the repairs? the front and rear parking lights are on the same fuse.

Sep 30, 2012 | 2005 Jeep Grand Cherokee

1 Answer

My husband replaced the turn signals & headlight & now car wont start


Hello! I sent a test procedure to you Wednesday evening but It appears you did not receive it ..This is the path for Battery and Ground to pull the crank relay which applies +12 volts to the starter solenoid..Either there is a fault in this path or the starter itself was damaged in the collision...Leaving the ignition switch when in start ...+12 volts on the Yellow wire goes to the Crank fuse (10A)...Other side of fuse is Purple wire to PCM C-2 Pin # 23...+ 12 volts at this point...PCM sends a ground on C-2 pin #76...Yellow/Black wire to crank relay....+ 12 volts from the PCM ABS fuse (10A)...via Park/Neutral switch to crank relay...Relay pulls and applies +12 volts on the Purple wire that goes to the starter...That +12 volts, if there,indicates a starter damaged in the collision...If not there chase it back until you lose it...Would you be so kind as to not rate my solution until the test procedure is accomplished...Send a comment..saailer

Sep 21, 2011 | 2000 Pontiac Montana

1 Answer

We have a 2004 60R withch has been great until a minor frontend, parking lot, collision a year ago.. the fron bumper was replace4d and the headlights have never worked well since. They point so rar down...


NEED TO LET A BODY SHOP CHECK OUT FRONT UNIBODY STRUCTURE FOR DAMAGE WHEN YOU HAD A FRONT END COLLISION. IF FRONT STRUCTURE BEND OR DAMAGED. THE FRONT BUMPER AND HEADLIGHTS FRONT WHEEL ALIGNMENT GOING TO BE OFF.SOUND LIKE FRONT END COLLISION IMPACT DAMAGED THE FRONT UNIBODY STRUCTURE.

Jul 10, 2011 | 2004 Volvo S60

2 Answers

How do you replace a headlight on a 2006 lincoln town car (low beam - left side)


Open the hood. Remove the black plastic grill assssembly ( Laying horizontal between the radiator and front bumper). There will be a couple of plastic screws (or some other fastening system) for this part remove and set aside. There is another black plastic grill assembly standing vertical. Remove similar fastening devices and set aside. IF DURING THIS ENTIRE PROCESS there is ANY part that does not come off freely after removing a fastening device (plastic screw, metal screws, hex bolts, bolts) LOOK FOR A PLASTIC CLIP - unclip that as a final step in each of these processes. To continue, Each headlight is attached by three hex or phillips screws.- Remove them and set asside. There is a major clip attaching the headlight at the top. Unattach this and gently remove the entire light housing. The housing will be the unit containing all parts high beam, low beams, side lights, and blinkers. It is a nice tidy unit. To continue, look for a black plastic removable panel on the back allowing access to the back of the bulbs. Remove the 5 screws and set asside. You now have access to the bulbs. The bulbs are attached by a solid plastic clip. Grab the back of the plastic bulb housing and turn about a half of an inch to remove the bulb. Unattach the clip from the wirering harness and you will have the bulb removed. CAREFULLY remove the new bulb making sure not to touch the glass portion of the bulb with hands directly. Skin oils or other debris is not recommended to get on the bulb. Deliberately refasten the bulb wiring harness and replace to the back of the reflection housing. Reassemble all devices. Rinse wash repeat for the other side :)

This seems complex for the task at hand and it is. But from the perspective of repairing a front end after a minor collision is is wonderful. Enjoy...

Jul 23, 2010 | 2006 Lincoln Town Car

2 Answers

Running lights don't turn on. indicator lamp flashes then goes out and headlights don't turn on


two things to consider here-has this car been in a front end collision and have you checked to see if the bulb in one light is burned out.wires for the light run across the front of the car and are easily damaged in a front end collision. also if a bulb is out you get this type of problem. It can be difficult to get top the bulbs. you need to remove screws just above the grille going into the core support and pull out on the grill/bumper cover to expose screws for the headlight then with the headlight loose pull it out a little and release the bulb. check the filament to see if it is broken

Apr 25, 2010 | 2005 Chevrolet Equinox

1 Answer

Transmission is locked after a minor front end collision.


Have you tried using your ignition key in the slot next to the gear selection handle?

Jun 17, 2009 | 1992 Honda Accord

Not finding what you are looking for?
2004 Mazda 6 Logo

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...