Question about 1999 Subaru Legacy

1 Answer

At oil light flashes shifts jerky style loses power

Blew a coolant hose it was small and located near the throttle body under where the position sensor plugs in. could coolant have contaminated my at fluid?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

More than likely your sensor got contaminated instead. Spray it with carburetor cleaner and blow it out with air, and put it back. It should cure your light problem.

Posted on Mar 18, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

L300 Saturn 2003 trying to replace my throtter sensor. Can't figure out where to start from. Have no idea where's it located.


Your vehicle has electronic throttle control an the Throttle position sensor's are internal to the throttle body assembly ! Your vehicle has two throttle position sensors .
Throttle Body Assembly
The throttle assembly contains the following components:
?€¢ The throttle blade ?€¢ The throttle actuator motor ?€¢ The throttle position (TP) sensor 1 and 2 You have to replace the Throttle Body Assembly !
Disconnect the negative battery cable. Remove the inlet hose assembly from the throttle body. Disconnect the throttle body electrical connection. Disconnect the hose clamps from the plenum-to-runner connector using theJ 43914 .
Remove the intake plenum bolts. Remove the EGR passage bolt. Rotate the plenum up and remove the throttle body coolant hoses, EVAP hose, and vacuum line from the throttle body.
Remove the throttle body nuts. Remove the throttle body.

Aug 05, 2015 | Saturn Cars & Trucks

2 Answers

99 cavalier, thick milky coolant in overflow, oil is fine, losing "coolant" but level is not going down


Automatic transmission ? If yes, I'd suspect transmission oil mixing with coolant in radiator.

Nov 21, 2013 | Dodge Cars & Trucks

1 Answer

Where is the throttle body on 2007 jeep patriot 2.4


In the 2007 jeep patriot the throttle body is located on the bottom right hand corner of the engine near the cooling fan, under the coolant hose coming from the radiator. If you follow the air intake hose from the air filter, which sits right above the battery, it ends at the throttle body. Once you take the battery out, undo the air intake hose from the filter, remove the filter casing, and undo the coolant hose from the engine you will have much easier access to the throttle body. The hardest part is loosening the clamp on the air intake hose connecting it to the throttle body (tight space). Once that hose is off, the throttle body has 4 bolts to the block and 1 mounting bracket bolt and than it comes out easy.

Jan 07, 2012 | 2007 Jeep Liberty Sport

1 Answer

How do you remove the thermostat on 2004 chevy venture?


FIRST YOU HAVE TO DRAIN COOLANT LEVEL BELOW THERMOSTAT THEN.TO REMOVE THERMOSTAT YOU HAVE TO REMOVE AIR FILTER DUCT AND MAF SENSOR TOGETHER.HAVE TO DISCONNECT ACCELERATOR CABLE AND TRANSMISSION SHIFT CABLE FROM THROTTLE BODY BRACKET. YOU HAVE TO REMOVE THROTTLE BODY UNIT REMOVE THE SMALL COOLANT HOSES FROM THROTTLE BODY,YOU NEED TO GO TO DEALERSHIP TO BUY THE SMALL COOLANT HOSES ATTACHED TO THE THROTTLE BODY.WHEN YOU REMOVE THE THROTLLE BODY UNIT.THEN YOU CAN REMOVE THERMOSTAT HOUSING TO REPLACE THERMOSTAT.YOU NEED TO BUY NEW THROTTLE BODY GASKET DONT REUSE OLD ONE.IF DO YOU WILL GET A VACUUM LEAK AND HAVE HIGH IDLE PROBLEM.

Aug 04, 2011 | 2004 Chevrolet Venture Passanger

2 Answers

Where is throttle positioning sensor on a suzuki forenza


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the Intake Air Temperature (IAT) sensor connector.
  3. Disconnect the breather hose from the valve cover.
  4. Remove the air intake tube.
  5. Disconnect the throttle cables by opening the throttle and moving the cable through the release slot.
  6. Disconnect the vacuum hoses from the throttle body.
  7. Disconnect the Throttle Position (TP) sensor and the idle air control valve connectors.
  8. Disconnect the coolant hoses from the throttle body.
  9. Remove the throttle body and discard the gasket.
  10. Remove the TP sensor.
  11. Remove the Idle Air Control (IAC) valve.
  12. Remove the throttle body retaining nuts.
  13. Remove the throttle body.

To install:

  1. Install the throttle body.
  2. Connect the TP sensor connector and the IAC valve connector.
  3. Connect the coolant hoses to the throttle body.
  4. Connect the vacuum hoses to the throttle body.
  5. Connect the throttle cable.
  6. Install the air intake tube.
  7. Connect the breather hose to the valve cover.
  8. Connect the IAT sensor connector.
  9. Connect the negative battery cable.
  10. Fill the cooling system
  11. shinehutt_33.gif
  12. i hope this helps tps is attatched to hrottle body on other side than throttle cable
  13. plz dont forget to vote rep[ly if you need more help

Jan 17, 2011 | 2006 Suzuki Forenza

1 Answer

Cant find a engine coolant bleeder on 04 lincoln ls


On a 3.9 V8 it is on the end of the hose under the
power brake booster,next to the degas bottle (coolant container)
below master cyl

On the 3.0 V6 it is on top off a coolant hose near
the throttle body

Nov 27, 2010 | 2000 Lincoln LS

1 Answer

No oil pressure, camshaft position sensor error,


Yes, the sensor is in small housing the goes in the hole where the distributor used to go. That also drives the oil pump so don't drive it you'll ruin the engine. It's located down under the throttle body, near transmission end of the engine.

Jan 04, 2010 | 1997 Mercury Sable

2 Answers

HOW DO I CHANGE THE THERMOSTAT ON A 1998 CHEVROLET LUMINA 3.1


FIRST OF ALL YOU HAVE TO DRAIN SOME COOLANT.JUST ENOUGH SO COOLANT WONT FLOW ALL OVER ENGINE.AND COOLANT TO EXPENSIVE ON THE GROUND.TO GET TO THERMOSTAT.YOU HAVE TO DISCONNECT CONNECTORS TO MAF EGR IDLE SPEED CONTROL AND IAT SENSOR.. REMOVE THROTTLE AND SHIFT CABLES FROM BRACKET.REMOVE AIR FILTER ASSEMBLY WITH MASS AIR FLOW SENSOR.REMOVE BOTTOM PORTION OF AIR FILTER HOUSING.REMOVE COOLANT HOSES FROM THROTTLE BODY.THEN REMOVE THROTTLE BODY ASSEMBLY.YOU HAVE TO DISCONNECT SMALL COOLANT HOSE TOP WATER PUMP.REMOVE SMALL BOLT THAT HOLDS METAL COOLANT LINE TO WATER PUMP.THIS LINE HAS TO BE MOVE JUST ENOUGH SO YOU CAN REMOVE THROTTLE BODY.ONCE THROTTLE BODY OUT THE WAY YOU CAN REMOVE THERMOSTAT.BESURE WHEN YOU PUT EVERYTHING BACK TOGETHER.REPLACE THROTTLE GASKET AND THE COOLANT HOSES COME OFF THROTTLE BODY BESURE TO USE OLD COOLANT HOSES MEASUREMENTS FOR NEW HOSES MEASUREMENTS MAKE SURE YOU BUY THE CURVE HOSE FOR THROTTLE BODY. DONT TRY TO USE STRAIGHT HOSE IT WILL KINK AND CAUSE NO COOLANT FLOW.WHEN YOU ARE DONE.FILL COOLANT BACK TO CORRECT LEVEL AND BLEED COOLANT SYSTEM.

Oct 25, 2009 | 1998 Chevrolet Lumina

2 Answers

I cannot locate the throttle position sensor on my 2000 catera


THERE IS NO CONVENTIONAL TPS, THROTTLE POSITION IS PART OF THE DRIVE BY WIRE SYSTEM IN THE THROTTLE BODY ASSEMBLY

Aug 26, 2009 | Cadillac Catera Cars & Trucks

1 Answer

Repeat bad o2 sensors, oil burning, engine cuts in clutch


You may have a blown heads. Try by replacing the oil pressure sensor located in the rear of the engine. Second clean the throttle body by taking off the hoses. Get the cleaner from the auto parts store. Clean throttle body, air intakes, air filter, new oil filter, and have your feul injectors services. Did you check under the car for oil leaks? Try placing a white sheet under the car to see if you have a bad oil spill. Make sure all harness wires are not shorting out. Alot of wires are placed close to heat sources and could melt them. Yoyu just have to replace the melted section and reroute the wiring........runjoe

Jan 23, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
1999 Subaru Legacy Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...