Question about 1992 Toyota Pickup

1 Answer

92 toyota pick up what is the procedure to replace

92 toyota pick up with fuel injection what is the procedure to replace the rocker arm gasket

Posted by on

  • Kelly C Bundy II May 11, 2010

    please specify the engine.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 365 Answers

It's called CHILTON's...check AutoZone or NAPA for books.
Good Luck
P.S. it's a VALVE cover gasket

Posted on Jun 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok so ik I'm posting allot haha but does anyone know where or how to adjust lifters just found out mine r just now needed adjustment in near mount Vernon WA or a price at least haha


In engines with rocker arm valve systems, the procedure I'm familiar with is to remove a rocker arm cover, and (one at a time!) while the engine is running, slowly back off the rocker arm retainer nut or bolt just until you hear the lifter tapping, then tighten it a quarter turn. If you can identify a lifter that is already tapping, tighten its rocker arm slowly until it stops tapping, then adjust it. Do not over-tighten! This can damage the engine.

Listen carefully to how the engine sounds; if it starts to stumble when you tighten a loose rocker arm, you've gone too far. If you cannot get the engine to run well without tapping, you may have too much wear in the valve train and may be due for a head overhaul, or you don't have adequate oil pressure in the lifters in question.
Repeat until all rocker arms are done. Replace the rocker arm cover using a new gasket, then (in a V-engine), repeat the procedure on the other side of the engine.

Wearing safety goggles, or better yet, a transparent face shield, is strongly recommended. Sometimes oil will squirt out a considerable distance from the lifter side of the rocker arm during adjustment, and the direction is not readily predictable.

Apr 03, 2015 | Cars & Trucks

3 Answers

Do I have to take the timming belt off to do a head gasket on a 1999 chevy malibu v6 3.1L


The 3.1 engine does not have a belt,it is a chain motor.You do not need to remove timing chain to remove head.

Apr 12, 2011 | 1999 Chevrolet Malibu

1 Answer

I need a print out of how i can change out a head gasket on a 1995 mercury cougar


Removal
  1. Drain engine cooling system.
  1. Disconnect battery ground cable (14301) .
  1. Remove engine air cleaner (ACL) (9600) including air cleaner outlet tube (9B659) .
  1. Loosen drive belt tensioner (6B209). Remove drive belts (8620) .
  1. If LH cylinder head (6049) is being removed, perform the following:
    1. Remove oil filler cap (6766) .
    1. Remove power steering pump front mounting bracket retaining bolts.
    1. Remove generator (GEN) (10346) and belt idler pulley (8678).
    1. Remove power steering pump/generator bracket retaining bolts. Leave hoses connected, place pump/bracket assembly aside in a position to prevent fluid from leaking out.
  1. If RH cylinder head is being removed, perform the following:
    1. Remove drive belts .
    1. If equipped with A/C, remove mounting bracket retaining bolts. Leave hoses connected and position A/C compressor (19703) aside.
    1. Remove positive crankcase ventilation valve (PCV valve) (6A666) .
  1. Remove upper intake manifold (9424) .
  1. Remove valve cover retaining bolts.
  1. Remove fuel injection supply manifold (9F792).
  1. Remove lower intake manifold as outlined.
  1. Remove exhaust manifolds (9430) as outlined.
  1. Loosen rocker arm seat retaining bolts enough to allow rocker arm (6564) to be lifted off the push rod (6565) and rotate to one side.
  1. Remove push rods . Identify position of each push rod . Push rods should be installed in their original position during assembly.
  1. Remove cylinder head retaining bolts and discard.
  1. Remove cylinder heads .
  1. Remove and discard old head gaskets (6051) .
Installation
  1. NOTE: Lightly oil all bolts and stud bolt threads before installation except those specifying special sealant.
    Clean cylinder head, intake manifold , valve cover (6582) and head gasket surfaces. If cylinder head was removed for head gasket replacement, check flatness and sealing areas for scratches of cylinder head and cylinder block gasket surfaces. Refer to Section 03-00 for procedure.
  2. Position new head gaskets onto cylinder block (6010) using cylinder head to block dowels (6A008) for alignment.

    Head Gasket


    a11431c.gif

  3. Position cylinder heads onto cylinder block .
  4. ani_caut.gif CAUTION: Always use new cylinder head bolts to ensure a leak-tight assembly. Torque retention with used bolts can vary, which may result in coolant or compression leakage at the cylinder head mating surface area.
    -ft).
  5. For 3.8L non-SC engine, tighten cylinder head retaining bolts in numerical sequence in three steps as follows:
    1. 20 Nm (15 Lb-Ft)
    1. 40 Nm (29 Lb-Ft)
    1. 50 Nm (37 Lb-Ft)
  6. ani_caut.gif CAUTION: Do not loosen all of the bolts at the same time, only work on one bolt at a time or possible damage to engine or leakage may occur.
    In sequence, loosen retaining bolts two to three revolutions and retighten bolts one at a time in the following manner:
    1. Long bolts:
      • 15-25 Nm (11-18 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.
    1. Short bolts:
      • 10-20 Nm (7-15 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.


      a11399c.gif


      Item Part Number Description 1 6010 Cylinder Block 2 - Locating Pin (2 Req'd) 3 N802515-S Cylinder Head Bolt (4 Req'd Each Side) 4 6049 Cylinder Head 5 N802516-S Cylinder Head Bolt (4 Req'd Each Side) 6 6A008 Cylinder Head to Block Dowel
  7. NOTE: If original valve train components are being installed, a valve clearance check is not required. If a component has been replaced, perform a valve clearance check as outlined.
    Dip each push rod end in Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A and install push rods in their original position.
  8. For each valve, rotate crankshaft (6303) until valve tappet (6500) rests on the heel (base circle) of the camshaft lobe, before tightening rocker arm seat retaining bolts to 7-15 Nm (5-11 lb-ft) maximum.
  9. Lubricate all rocker arms with Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A. Final-tighten the rocker arm seat bolts to 30-40 Nm (22-30 lb-ft). For final tightening, camshaft (6250) may be in any position.
  10. Install exhaust manifolds as outlined.
  11. Install lower intake manifold as outlined.
  12. Install fuel injection supply manifold .
  13. Position valve cover and new valve cover gasket (6584) on cylinder head and install retaining bolts. Note location of ignition wire routing clip stud bolts. Tighten retaining bolts to 9-12 Nm (7-9 lb-ft).
  14. Install upper intake manifold .Install spark plugs (12405) , if removed.
  15. Connect ignition wires to the spark plugs .
  16. If LH cylinder head is being installed, perform the following:
    1. Install oil filler cap.
    1. Install generator/power steering pump mounting bracket.
    1. Install generator .
    1. Install main accessory drive belt tensioner .
    1. Install power steering pump (3A674) .
    1. Install power steering pump support bracket.If RH cylinder head is being installed, perform the following:
    1. Install positive crankcase ventilation valve .
    1. If equipped with A/C, install A/C compressor mounting brackets (2882) and A/C compressor .
  17. Install drive belt and tighten to specification.
  18. Connect battery ground cable .
  19. Install air cleaner outlet tube.
2010&c18=modelyear&c35=wsm%2ccylinder%20heads%2cssd%2c03-01a%2cin-vehicle%20service&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 06, 2011 | Mercury Cougar Cars & Trucks

1 Answer

Where is the fuel pump located for a toyota pick up 1987


It's located at the front of the engine usually gold and on the left hand side of the rocker arm cover almost directly across from your distributor cap. Can't miss it.

Mar 01, 2011 | 1987 Toyota Pickup

1 Answer

Need head bolt torqe for 3100 and should bolts be dry


The bolts should have thread lock on them when installing, and the torque is done in 2 steps. 33 ft lbs. and then 90 deg. after that on the second pass. 3.1L Engine CAUTION
Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well ventilated area. Do not allow fuel spray or vapors to come in contact with a spark or open flame. Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion. LEFT SIDE (FRONT)
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system into a suitable container.
  4. Disconnect the top half of the air cleaner assembly, then remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Disconnect the spark plug wires from spark plugs and looms then route the wires out of the way.
  7. Remove the rocker arm (valve) covers.
  8. Remove upper intake plenum and lower intake manifold.
  9. Remove the left side exhaust manifold.
  10. Remove oil level indicator tube. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  11. Remove rocker arms nut, rocker arms, balls and pushrods.
  12. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To install:
  13. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  14. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP are showing.
  15. Coat the bolt threads lightly with sealer, then install finger-tight.
  16. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  17. Install the pushrods, rocker arms, balls and rocker arm nuts in their proper locations. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  18. Install the lower intake manifold and upper intake plenum.
  19. Install the rocker arm (valve) covers.
  20. Install the oil level indicator tube. Insert the dipstick.
  21. Connect the spark plug wires to spark plugs and looms.
  22. Install the left side exhaust manifold.
  23. Install the exhaust crossover pipe and heat shield.
  24. Refill the cooling system.
  25. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  26. Connect negative battery cable.
  27. Start vehicle and verify that there are no leaks. Fig. 20: Cylinder head mounting and bolt tightening sequence - 3.1L engine 86883134.gif
RIGHT CYLINDER HEAD (REAR) CAUTION
Fuel Injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove the top half of the air cleaner assembly and remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Raise and safely support the vehicle.
  7. Detach the Oxygen (O2) sensor connector.
  8. Disconnect the exhaust pipe from the exhaust manifold.
  9. Remove the right side exhaust manifold.
  10. Carefully lower the vehicle.
  11. Disconnect the spark plug wires from spark plugs and wire looms and route the wires out of the way.
  12. Remove the rocker arm (valve) covers.
  13. Remove upper intake plenum and lower intake manifold. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  14. Remove rocker arms nut, rocker arms, balls and pushrods.
  15. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To Install:
  16. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  17. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP showing.
  18. Coat the bolt threads lightly with sealer, then install finger-tight.
  19. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  20. Install the pushrods loosely retained with the rocker arm assemblies. Make sure all pushrods are in the correct locations. Coat the ends of the pushrods with prelube. The intake rods are marked yellow and are 5 3?4 inch long. The exhaust pushrods are marked green and 6 inches long. balls and rocker arm nuts. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  21. Install the lower intake manifold and upper intake plenum.
  22. Install the rocker arm (valve) covers.
  23. Connect the spark plug wires to spark plugs and wire looms.
  24. Raise and safely support the vehicle.
  25. Install the exhaust manifold.
  26. Connect the exhaust pipe to the exhaust manifold.
  27. Carefully lower the vehicle.
  28. Connect the Oxygen (O2) sensor wiring.
  29. Install the exhaust crossover pipe and heat shield.
  30. Refill the cooling system.
  31. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  32. Connect negative battery cable.
  33. Start vehicle and verify that there are no leaks.
prev.gif next.gif

Feb 04, 2011 | 1997 Oldsmobile Achieva

1 Answer

I need to replace the fuel pump in my 1985 Chevy S10 pickup, need all help. What is the procedures?


EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL
  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Mar 22, 2009 | 1985 Chevrolet S-10

2 Answers

1993 TOYOTA TERCEL 1500cc Valve Seals Replaced now smokes much worse


You either have had the wrong valve seals installed, they are physically missing, or the valves are incorrect (too loose in the guides/stem too thin). The rocker arm seals will not contribute to your issue. If it did not have the oil smoke before you took the head off, the issue is with whatever the machine shop did. Valve seals have to fit TIGHT, or oil will go down the valve stem into the intake.
Take the head back to the machine shop & tell them to fix it. For free.

Aug 23, 2008 | 1993 Toyota Tercel

1 Answer

1.5 liter standard '92 Tercel


Remove the valve cover and check to see if you have a rocker stud or cam bearing cap that has either broken or worked itself loose.

Aug 07, 2008 | 1992 Toyota Tercel

Not finding what you are looking for?
1992 Toyota Pickup Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...