Question about Cars & Trucks

1 Answer

NISSAN NOTE having a problem on accelerator pedal position sensor . how do i repaire it.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 201 Answers

Throttle position sensor can be bought at parts store and replaced

Posted on Mar 20, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 2010 Chevy impala. Reduced engine power. Service traction control and stability track. and check engine light. Codes are P2138 P2122 P0455


Electronic throttle control !
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

2009 Chevy Silverado P2138 Accelerator Pedal Position


Circuit/System Description
The throttle actuator control (TAC) system uses two accelerator pedal position (APP) sensors to monitor the accelerator pedal position. The APP sensors 1 and 2 are located within the pedal assembly. Each sensor has a 5-volt reference circuit, a low reference circuit, and a signal circuit.
Two processors are also used to monitor the TAC system data. Both processors are located within the engine control module (ECM). Each signal circuit provides both processors with a signal voltage proportional to pedal movement. The processors share and monitor data to verify that the indicated APP calculation is correct.

DTC P0455: Evaporative Emission (EVAP) System Large Leak

The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge solenoid valve OPEN and the EVAP vent solenoid valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. The following table illustrates the relationship between the ON and OFF states, and the OPEN or CLOSED states of the EVAP canister purge and vent solenoid valves.

Nov 03, 2017 | Cars & Trucks

1 Answer

Nissan 350 z p1762 code


P1762 Nissan - Direct Clutch Solenoid Valve Possible causes
- Faulty Direct Clutch Solenoid Valve
- Direct Clutch Solenoid Valve harness is open or shorted
- Direct Clutch Solenoid Valve circuit poor electrical connection
P1762 Nissan Description
Direct clutch solenoid valve is controlled by the Transmission Control Module (TCM) in response to signals sent from the PNP switch, vehicle speed sensor and accelerator pedal position sensor (throttle position sensor). Gears will then be shifted to the optimum position.

Dec 07, 2013 | Cars & Trucks

2 Answers

Reduced engine power, service traction control, service stabilitrak


First of all a scan tool is need for this not a code reader, you need to view scan data after you find what code is stored in the PCM. It could have a problem with the powertrain control module, wiring, or the Accelerator Pedal Position (APP) Sensors. Here are a few codes that could set .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Oct 02, 2012 | 2008 Chevrolet Tahoe LS

3 Answers

Error code p2138


Here is the definition. You may need to have someone check the accelerator pedal position sensor and the circuit.

P2138 NISSAN Description The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the Engine Control Module (ECM).
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
Read more: http://engine-codes.com/p2138_nissan.html#ixzz26J3D2x8s

Sep 12, 2012 | 2010 Nissan Versa 1.8

1 Answer

2005 Mazda 6 4cyl AT Idles high after driving a while.


I would check the pedal position sensor. Do it when it's hot.
Mazda Car 2005-06
  • Accelerator Pedal Position Sensor

    Description & Operation

    A power supply is applied on the Accelerator Pedal Position (APP) Sensor (main) power terminal from the PCM. The ground terminal is grounded with PCM. When the accelerator pedal is moved from the idle position to the fully opened position, the resistance between the accelerator pedal position sensor (main) output terminal and ground terminal will increase according to the depression.
    A power supply is applied on the Accelerator Pedal Position (APP) Sensor (main) power terminal from the PCM. The ground terminal is grounded with PCM. When the accelerator pedal is moved from the idle position to the fully opened position, the resistance between the accelerator pedal position sensor (main) output terminal and ground terminal will increase according to the depression.

Testing

  1. Connect a suitable scan tool to the diagnostic connector. Select APP1 or APP2 percentage.
  2. Turn the ignition switch to the ON position.
  3. Measure the voltage at the PCM terminal and ground with connectors connected:

    APP1-8% load or 0.4 volts with the accelerator pedal releasedAPP1-60% load or 3.0 volts with the accelerator pedal depressedAPP2 -8% load or 0.4 volts with the accelerator pedal releasedAPP2 -60% load or 3.0 volts with the accelerator pedal depressed
  4. If any check above does not meet the specifications, check connectors and wiring between the sensor and PCM. If ok, replace PCM.
  5. If the measured values are outside the standard value range, or if the load % and/or voltage does not change smoothly, replace the sensor.
  1. Connect a suitable scan tool to the diagnostic connector. Select APP1 or APP2 percentage.
  2. Turn the ignition switch to the ON position.
  3. Measure the voltage at the PCM terminal and ground with connectors connected:

    APP1 %-31.0-32.4% with the accelerator pedal releasedAPP1 %-69.8-81.8% with the accelerator pedal depressedAPP2 %-20.2-21.4% with the accelerator pedal releasedAPP2 %-58.8-70.8% with the accelerator pedal depressed
  4. If any check above does not meet the specifications, check connectors and wiring between the sensor and PCM. If ok, replace PCM.
  5. If the measured values are outside the standard value range, or if the load % does not change smoothly, replace the senso

0996b43f80203317-l15fcbeisfileg1jtnhunp3x-3-0.gif

Jul 23, 2017 | 2005 Mazda 6

1 Answer

I have an 2006 lincoln navigator and i had 2 codes p2104 and p2112 i changed #2 spark plug and coil then i got a fail safe mode turned truck off then back on then went away then i got the two codes p2104...


Hi, there is a post here on this issue: http://www.fordf150.net/forums/viewtopic.php?t=50060&highlight=p2104

Since you have already changed the TPS, I assume you also cleaned the throttle body? Is the throttle actuating smoothly? If not, make any repairs needed to make it smooth and easy to rotate the throttle.
If the throttle is good, then test the accelerator position sensor per the procedure below.
Please let me know if you have any questions, and thanks for using FixYa.
OperationThe APP sensor is an input to the powertrain control module (PCM) and is used to determine the torque demand. There are 3 pedal position signals in the sensor. Signal 1, APPS1, has a negative slope (increasing angle, decreasing voltage) and signals 2 and 3, APPS2 and APPS3, both have a positive slope (increasing angle, increasing voltage). During normal operation APPS1 is used as the indication of pedal position by the strategy. The 3 pedal position signals make sure the PCM receives a correct input even if 1 signal has a concern. There are 2 reference voltage circuits and 2 signal return circuits for the sensor.
Removal & Installation
  1. Disconnect the battery ground cable.
  2. Disconnect the accelerator pedal position sensor electrical connector.
  3. Remove the 3 bolts and the accelerator pedal assembly.

To install:
  1. Install the 3 bolts and the accelerator pedal assembly.
  2. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).

Testingjturcotte_1769.gif

Fig. 5.4L APP sensor connector

  1. Checking the VREF voltage to the Accelerator Pedal Sensor

    Turn the ignition switch to the off position. Disconnect the Accelerator Pedal sensor connector. Measure the voltage between pin 6, 7 (ETCREF+) and 1, 3 (ETCRTN-). The voltage should read between 4-6 volts, If not repair circuits in question.
  2. Checking the Functionality of the APP sensor.

    Turn the ignition off. Disconnect the Accelerator Pedal sensor connector. Refer to Resistance Chart:

    jturcotte_1770.gif

    Fig. APP Diagnostic resistance chart

May 27, 2011 | Lincoln Navigator Cars & Trucks

3 Answers

Nissan Maxima 2004 won't accelerate. It runs well up to 2000rpm then will not go any faster. The engine fault light is on. The error seems to be related to the airflow intake. A mechanic who was too busy...


1st, you should get the Engine Controls (EC) section of the service manual. You can download it HERE

Now you need get the diagnostic codes from your vehicle. The procedure is:

HOW TO SWITCH DIAGNOSTIC TEST MODE
NOTE:

- It is better to count the time accurately with a clock.
- It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit
has a malfunction.
- Always ECM returns to Diagnostic Test Mode 1 after ignition switch is turned OFF.
How to Set Diagnostic Test Mode II (Self-diagnostic Results)
(key in the on position, engine off)
1. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
2. Repeat the following procedure quickly five times within 5 seconds.
a. Fully depress the accelerator pedal.
b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the MIL starts blinking.
4. Fully release the accelerator pedal.
----------------
The check engine light will then flash the 4 digits of the code. (refer to (EC) page 68)

Or you can go to an autozone and ask them to scan your vehicle for codes. They will do it for free.

Once you have the diagnostic codes, you can find the code info and diagnostic procedures in the (EC) manual.

Feb 28, 2011 | 2004 Nissan Maxima

2 Answers

Code p2138


P2138 is Throttle Pedal Position Sensor/ Switch D / E Voltage Correlation. Replace the Throttle Pedal Position Sensor/Switch.Remember to have the set code Cleared from the cars computer, this will turn off the check engine light and reset it. Good Luck and have a good XMASS.

Dec 17, 2010 | 2006 Nissan Altima

1 Answer

Intermittent power loss after accelerating hard


hi what is your car have no codes come up if not do a fault reading see if it has stored any as tps [throttle position sensor ] map sensors and airflow sensors will cause this problem as will a few others it can be expensive guessing yates210456

Oct 17, 2008 | 2003 Nissan Se R

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...