Question about Smart Cars & Trucks

Open Question

How to change the interion bulb place in the bar of a soft top smart passion

Smart pasion

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 passion dash lights fuse blew 7.5amp number 6 replaced fuse with 10amp,all i had at time, now smell of burning and dash lights except clock are out again.


Hello
When a fuse blows up , means you have an electrical problem in that circuit, you need to check the wires that are connected to that fuse for short circuit

Jan 12, 2017 | Smart Cars & Trucks

1 Answer

Need to repair a stuck soft top on my 08 Smart passion


please explain exactly how does it get stuck?

Dec 02, 2016 | Smart Cars & Trucks

1 Answer

Car wont go into gear automatic


I had the same problem with my 2009 Smart fortwo passion. Ended up being dirt in the switch that senses when you put the shifter in manual. Unstuck the switch and all is shiney again. The Smart forums give instructions on getting to the switch.

Mar 30, 2014 | Smart Cars & Trucks

1 Answer

How does one change a headlight bulb on a 2005 1500hd silverado?


will try to help. open hood go to side blown bulb is at. look above the headlight, see a silver bar on top of headlight assembly? slide it out, carefully,lift the headlight assembly upwards,after the assembly comes up, disconnect the bulb by twisting the bulb assembly to your left,bulb should come out squeeze the bulb at the base,you should see the silver clips that hold bulb in. after old bulb out, push the new bulb in twist the holer back to your right[backwards] right.replace the headlight assembly back into place[mindful of plastic rings that the silver pin slides through to retain it] slide the silver pin back through the plastic holes that holds the light into place. thank you for choosing fixya.com and as always.,if you need further assistance,please repost your question and we'll ba happy to help

Nov 28, 2010 | 2005 Chevrolet Silverado 1500HD

3 Answers

How do you change headlight bulb on 03 Eclipse


First, make sure that the headlights and engine are off. Hot engine and hot bulb make changing it challenging. Reach behind the headlamp assembly and remove the electrical connector by pulling it straight out, towards that back of the car. Next, remove the large rubber seal that is on the back of the headlight assembly by pulling it off like the electrical connector. The electrical connector was in the center of the seal. There is a metal bar spring that goes across the back of the bulb assembly. It opens like a safety pin. Gently push down on the end of the metal spring. Once it is pushed down it will be out of its clasp and it will open automatically due to spring tension. The bar spring can be opened completely and then the bulb will come straight out the back of the headlamp assembly. To replace the bulb, first, make sure you don't touch the glass on the bulb since it may cause a hot spot and reduce the life of the bulb. There are 3 metal tabs that are on the bulb for the electrical connector. Position the bulb so that the "missing tab" is on the bottom. Put the bulb into position by aligning the 3 metal fingers on the outside of the bulb assembly into the openings on the back of the headlamp. They should seat fully. Once the bulb is in place you can close the bar spring by gently pushing down on the open end of the spring so that it engages the clasp. The spring will hold the bulb in place and you can verify seating by gently trying to move the bulb or by gently pushing and pulling the bulb. If it is seated then you can put the large rubber seal back on the back of the headlamp. Lastly you can pusht the electrical connector back onto the 3 prongs of the bulb. Don't push too hard and you might want to consider using some bulb grease to make it go on easier and to protect from corrosion. I changed both headlamps in about 3 - 5 minutes.

Jan 16, 2010 | 2003 Mitsubishi Eclipse Coupe

1 Answer

Ref: Smart Car fortwo Passion 2004 698cc semi auto model I cannot find any catches or levers to open the front panel so I can top up the windscreen washer. How do I do it please.


You can not open the panel it self. to top the windscreen washer , face the car and you will see 2 small grills under the windscreen , remove the one to the left , you can see a small plastic bolt in the middle of it , just turn it half a turn and remove the small grill , look inside you will see the windscreen water canister , remove cap and fill with water , close cap , put the grill back , lock with the bolt , and you are done. good luck

Jan 01, 2010 | 2008 Smart fortwo

2 Answers

Smart Passion won't start


Check the battery in the remote as you should here a bleep in the car when the imoboliser is turned off we have the smart diagnostic computer svs 07923 479640

Jun 13, 2009 | 2008 Smart fortwo

1 Answer

I need to change stop light bulbs in my 1998 lincoln town car


open the trunk, and pull the linning away from the body. It should easly move. you have access to the lighting fixture. determine which is the stop light and turn the base counterclockwise to open. remove the blown bulb. To install the new, do not touch with your bare hands, use a soft cloth or paper towel to seat the bulb into its socket. reinstall by truning the bulb clockwise to seat in place. Press your linner back into place.

Dec 10, 2008 | 1998 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smart Experts

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Are you a Smart Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...