Question about Cars & Trucks

Open Question

JURGENS PALMA BRAKE ADJUSTMENT MANUEL - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need parts for VW Jurgens - Brakes parts 211 615 269A spring x2 and 211 615 261A pins x4 - also Windscreen wiper motor and front grill


so call an auto parts supplier?? this isnt rocket science and we dont sell any parts here. we offer advice only.

Aug 01, 2017 | Cars & Trucks

2 Answers

How do i tighten my emergency brake


Depends on the type of vehicle. Some have adjustments on the cables under the vehicle. Others have an adjustment that is automatically done when you back up and aggressively push the brake pedal.

Feb 27, 2015 | Cars & Trucks

1 Answer

How to tighten handbrake nissan 1991


Look at the Manuel and find out where the adjustment on the break cable is and tighten it acording to what the Manuel says should be pretty straight forward or google it

Jun 24, 2014 | 1991 Nissan Sentra 2 Door

1 Answer

The cables that lift the roof of my Jurgens slipstream van has brokencaravan problems


You might be able to get replacement cables. You can check online, with a service shop, or at the original dealers. I would suggest asking for instructions on how to install them. It shouldn't be too difficult, but it might be a lot of busy work.

Elisa Jed ' http://www.bwattspanelandpaint.com.au

Apr 07, 2014 | Cars & Trucks

1 Answer

Palma campbell


You are listing in the Cars and Trucks category and not under anything with Communications.

Apr 26, 2013 | Ford Cars & Trucks

2 Answers

Need to find owners manuel for ford 2002 ford cru cabb my brake ligth's dont turn on


check brake light switch under dash follow brake pedal up to steering column where they meet is brake light switch check for properly in place than test switch if bad replace

Feb 02, 2010 | Ford F-150 Cars & Trucks

1 Answer

Susuki xl7 2003 stuck in park?


It might be the shiftlock. On newer cars you have to press the brake pedal in order for it to shift out of park. There is a manuel override in the owners manuel. There is a switch on the brake pedal that would need to be replaced.

Jul 09, 2009 | 2003 Suzuki XL-7

1 Answer

Adjusting Padking Brake with 4 wheel disc brakes.


Hope this helps. This is out of the factory manual. Let me know if this works for you.
PARKING BRAKE NOTE: Tensioner adjustment is only necessary when the tensioner, or a cable has been replaced or disconnected for service. When adjustment is necessary, perform adjustment only as described in the following procedure. This is necessary to avoid faulty park brake operation.
  1. Raise vehicle.
  2. Fully back off cable tensioner adjusting nut at equalizer to create slack in cables.
  3. Remove rear wheel/tire assemblies. Remove brake calipers and rotors.
  4. Verify park brakes are in good condition and operating properly.
  5. Verify park brake cables operate freely and are not binding, or seized.
  6. Check park brake shoe adjustment.
  7. Reinstall rotors and make sure rotors turn freely.
  8. Reinstall brake calipers. Tighten guide pin bolts to 41 n·m (30 ft.lbs.)
  9. Reinstall wheel/tire assemblies after brake shoe adjustment is complete.
  10. Lower vehicle enough for access to park brake foot pedal. Fully apply park brakes
NOTE: Leave park brakes applied until adjustment is complete.
  1. Raise vehicle again.
  2. Mark tensioner rod 6.35 mm (1/4 in.) from edge of tensioner bracket Adjustment Mark On Cable Tensioner Rod
  3. Tighten adjusting nut at equalizer until mark on tensioner rod moves into alignment with tensioner bracket
CAUTION: Do not loosen, or tighten the tensioner adjusting nut for any reason after completing adjustment.
  1. Lower vehicle until rear wheels are 15-20 cm (6-8 in.) off shop floor.
  2. Release park brake foot pedal and verify that rear wheels rotate freely without drag. Verify pedal returns to fully released position.
  3. Lower the vehicle

Mar 09, 2009 | 1999 Chrysler 300M

1 Answer

Park Brake Adjustment



Park Brake Adjustment (Disc Brake)

Tools Required

j 21177-A Drum-to-Brake Shoe Clearance Gage

Park Brake Shoe Adjustment

Caution: Refer to Brake Dust Caution.

Important: The park brake shoes must be adjusted before the park brake cable tension is adjusted.Set the J 21177-A so it contacts the inside diameter of the rotor
  1. Position the J 21177-A over the shoe and the lining at the widest point.
  2. Turn the adjuster nut until the lining just contacts the J 21177-A. Park brake shoe to brake rotor clearance: 0.6604 mm (0.026 in)
  3. Repeat steps 1-3 for the opposite side.
Park Brake Cable Tension Adjustment

Important: Before you adjust the park brake cable tension, verify that the park brake shoes are adjusted to provide a clearance of 0.6604 mm (0.026 in) and the rear disc brake rotors are installed.

  1. Verify the self adjuster lock-out pin has been removed.
  2. Fully apply and release the park brake pedal 3 times.

Feb 22, 2009 | 2007 GMC Sierra C/K2500

1 Answer

1995 ford mustang break lights do not work.


get a manuel from an auto parts store. in this manuel it will have etm(electrical troubleshooting manuel) it shows the brake lights and wires colors of wires. trace the wire color from the fuse using the diagram. purchase a test light from wal mart to see if your wire has power. if it does there may be a bad connection or component but hte etm shoud show you what components are on the circuit.any questions email me at jacobtaylor3@yahoo.com

Dec 31, 2008 | 1995 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...