Question about 1999 Daewoo Nubira

Open Question

How do you program a key for a 2001 daewoo nubira?

I need to program a new key.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: replacing timing belt on daewoo nubira 2000 model

Instructions Difficulty: Moderate Things You’ll Need:

  • Set of ¼-inch drive sockets ¼-inch drive ratchet Set of ½-inch drive sockets ½-inch drive ratchet Set of 3/8-inch drive sockets 3/8-inch drive ratchet Set of metric wrenches Floor jack Jack stands
Step1 Raise and support the vehicle on jack stands. Remove the intake air temperature wiring, the breather hose and intake air hose. Take off the air cleaner assembly. Step2 Remove the right wheel. Remove the accessory belts. Remove the crankshaft bolt and the crankshaft pulley. Remove the power steering bolts and the timing belt covers. Temporarily install the crankshaft bolt and turn the engine clockwise until the mark on the crankshaft pulley, which is a triangle stamped into the crank sprocket, is aligned with the corresponding triangular mark on the block. Step3 Make sure that the timing marks are aligned on the camshaft sprockets. These are a line on each sprocket that runs through a tooth on each sprocket. These lines should line up in the middle between each sprocket and point toward each other. If they do not line up, turn the crankshaft one more time and they will line up. It takes two turns of the crank to one complete revolution of the cam. Step4 Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water pump clockwise away from the belt and loosely tighten the bolts to keep it there. Remove the timing beltmag-glass_10x10.gif. Make sure the timing marks are aligned and install the new belt starting on the right side from the crank sprocket and working counterclockwise. Keep all the belt tension on the right side away from the tensioner. Step5 Loosen the bolts in the water pump and rotate the water pump counterclockwise to apply tension to the belt. Watch the tensioner, which is above the water pump, and apply tension with the water pump until the pointer on the tensioner lines up with the notch above it. Lightly tighten the water-pump bolts. Step6 Turn the engine two more times and align the timing marks perfectly. Loosen the water-pump bolts and, using the ratchet, apply tension to the belt until the tensioner pointers are aligned. Tighten the water-pump bolts. Step7 Install the timing-belt covers and the bolts in the power-steering pump and tighten. Remove the crankshaft bolt and install the crank pulley and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds of torque. Install all components in reverse order of removal.

Posted on Mar 08, 2009

stevenhurc
  • 450 Answers

SOURCE: my car daewoo nubira 1998 stopd at idle speed and the center luck

these vehicles had a zylux immobiliser fitted at point of entry to Australia others had after market system fitted they didnt actuall build them with these features.you need to go to a dealer to repair or program new remote, have you got a second key remote? this one might still work

Posted on May 28, 2009

stevenhurc
  • 450 Answers

SOURCE: program remote door lock 2000 Daewoo Nubira

the keyless entry remote needs programming by dealer who has daewoo scan 100 tool or GM dealer with Tech2 need code from owners book if not code is on compliance plate last 5 digits in 6 digit DSN number bottom right corner.

Posted on Jun 21, 2009

alicantecoli
  • 22095 Answers

SOURCE: 2000 Daewoo Nubira camshaft position sensor

on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Posted on Sep 11, 2009

  • 1986 Answers

SOURCE: How to scan the 2001 daewoo nubira fault codes.

Your port should be located under the dash on the driver's side near your knee area. The port should be pointing straight down from the dash. The scanner will be plug and play and you shouldn't have to jump and pins for the OBD-II port. As for the codes, there are so many thousands of codes that you can't even guess what codes will be generated from your scan

Posted on Sep 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do you have to have two programmed ignition keys in order to program a new chip key. ?


probably need to keys so that a key could be clone from a good key
if you lost a key and want a spare , there is no way around it except to buy a new fob key and have it programmed to the immobilizer system

May 20, 2016 | 2006 Ford Taurus

1 Answer

My key won't turn in my 2001 daewoo nubira why?


Try a spare key if you have one... Try a little lubricating oil. If that is your original key and it does not turn after lubricating it might be best to seek the services of a GOOD mechanic to replace the cylinder, you do not want it to suddenly lock up again

Jun 10, 2015 | 2001 Daewoo Nubira

1 Answer

Theft light flashes car wont stay running


You need to bring it to the DEALER...

1997 Does not allow Self Programming over the 4 Hour Period. Since you do not have an Original Key that will work (you swapped out an Operating System). The DEALER must go into the Computer and RELEARN the KEY.

Make sure you bring ALL YOUR NEW KEYS and do them ALL at once...

Apr 08, 2013 | Cars & Trucks

1 Answer

Got new key fob for my 2006 chevy malibu ss how do I program it to work


How to Program a Key FOB for the Chevy ' eHow.com

www.ehow.com/how_7508133_program-key-fob-chevy.html

How to Program a Key FOB for the Chevy ... your Chevy, if you obtain new or replacement keys they will need programming to work with ... How Do I Program MyKey Fob? ...

Mar 14, 2013 | Cars & Trucks

1 Answer

New key programming for lancer 2005


you need to first install one of factory key into ignition.turn ignition switch on position for 5 seconds.switch off the ignition and remove key.wait 7 seconds insert new key into ignition switch.and switch ignition on until alarm system warning lamp will flash twice mean key programmed. switch ignition off if warning light illuminate for 3 seconds to confirm or flash 3 times indicate registration has failed. if you fail on programming new key let dealership reprogram new keys using diagnostic equipment.

Dec 20, 2012 | 2002 Mitsubishi Montero Sport

1 Answer

Had only 1 key and broke it however walmart was able to cut a new one but need to no how to program it


I have a 2007 Lincoln Navigator...
Less than 1 hour ago (4:00pm pacific time) I had a key made AND programed at my local Walmart (over in the auto department). It cost me $54.00 and took all of 15 minutes from beginning to end. The key works perfectly - no problems...
They have a machine that reads the code on your original key - then they insert the new key blank and your original code is programed into the new key - THEN they cut the key and you are out of the door.

Feb 19, 2012 | Cars & Trucks

1 Answer

I have a 2004 Cadilac CTS we bought a replacement chip key which the Chev Olds dealer could not program I took the new key to a Cadilac dealer they told me the key is defective now the Chev dealer has...


Okay, to program a key you will need two keys that are already programmed, insert one key ignition turned on and engine off, remove the key and within 10 sec insert the second key and turn ignition on with engine off, remove that key and within 10 sec insert the key to be programed. you will need to do a 30 min.relearn with only one key,you will turn ignition on with engine off and wait about 10 min until light goes out then remove the key and repeat this step when light goes out repeat step one more time then use key to start car, computer has learned all info. you will now turn off engine, insert programmed key turn key on engine off then remove the key and insert key to be programed within 10 sec.all done good day.

May 27, 2011 | 2004 Cadillac CTS

1 Answer

What are the torque specifications and tightening sequence for cam journal and cylinder head for 2001 daewoo nubira 2.0 :(


  1. The torque settings for the cylinder head bolts on a daewoo ...

    www.answers.com > ... > Categories > Cars & Vehicles > Asian Car i need how much pression (torque) for head daewoo nubira 2001 2.0 ... What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and ...

Apr 15, 2011 | 2001 Daewoo Nubira

1 Answer

I heard that 2001 daewoo nubiras were recalled, who can i contact if i believe i have a defective unit?


ok you can check if you have any of the recall problems here http://www.autorecalls.us/aut-04/recalls/2001/daewoo/nubira/78657.html then contact the nearest daewoo dealer to arange repairs. these should be at no expense to you as they are factory faults. hope that helps. let me know how you go.

Feb 04, 2011 | 2001 Daewoo Nubira

Not finding what you are looking for?
1999 Daewoo Nubira Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...