Question about 2009 Mitsubishi Outlander

Open Question

Side marker assembly

How to replace

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why would only one out of 4 marker lights work?


you are right all marker lights come off of one fuse, inside instrument panel, number 29, a 10 amp fuse my manual does not give a lamp number, it has a chart, head lamps (high) lamp 9005 60 w type a, headlamp (low) 9006 51 w type b, front marker lamps 5w type d, for the rear it says to use a lamp 7443 21.5 w type d, I do not use these, I have special lights on mine, hope that it helps

Mar 28, 2015 | 2007 Scion tC

1 Answer

Side marker bulb on 97 miata


The process is straightforward; remove the 2 mounting screws and pull the marker assembly out. The lamp itself is socketed in a turn-and-lock assembly. Twist counterclockwise to remove. Replacement lamp for the 93-97's is a 1157LL in the rear and a BP194 in the front.

Jan 09, 2012 | Mazda MX-5 Miata Cars & Trucks

1 Answer

Replacing a turn signal bulb....Baffled...Thanks


Hello,

Please do not be baffled. To replace the turn signal bulb on Your car is quite simple, all You need to do is to get a screwdriver and follow the steps below:
  1. Open the hood and locate the mounting screws for the outboard marker-light assembly just above the light. Remove the screws with a Phillips screwdriver, then remove the assembly, setting it aside for now.
  2. Locate the two mounting screws on top of the turn-signal light assembly under the side-marker lens. Remove the two screws with a Phillips screwdriver, then set the screws aside. Slide the turn signal out and locate the socket on the back of the assembly.
  3. Rotate the bulb socket counterclockwise and pull the socket out of the assembly. Pull the bulb straight out of the socket and discard it. Install a new bulb into the socket, pushing it in until is seats. Position the socket back into the rear of the light assembly, turn it clockwise to lock it in place, then slide the assembly back into the front of the Jeep.
  4. Install the mounting bolts that secure the turn-signal light assembly, tightening the screws with a Phillips-head screwdriver. Position the side marker-light assembly to the side of the Jeep and install the retaining bolts.
  5. Tighten the retaining bolts for the side-marker lights with a Phillips screwdriver, then close the hood. Test the repair by turning the lights on and visually verify that the light is working..
Hope this helped. Thank You for using FixYa!!!

Jan 28, 2011 | 1998 Jeep Grand Cherokee

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

1 Answer

Need help changing out the low beam on drivers side of 2006 buick rainier


Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.


  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
    counterclockwise.

To Install:


  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket
    clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)
gm-06-00-1591.gif




  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp
    assembly.
  6. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp
    assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)
gm-06-00-1590.gif




  1. Release the headlamp assembly retaining tabs.
  2. Disconnect the headlamp connector.
  3. Remove the park/turn bulb socket from the headlamp assembly.
  4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
    socket from the headlamp assembly.
  5. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
    socket into the headlamp assembly.
  3. Install the park/turn bulb socket into the headlamp assembly.
  4. Connect the headlamp connector.
  5. Lock the headlamp assembly retaining tabs.


prev.gif next.gif

Oct 28, 2010 | 2006 Buick Rainier

2 Answers

How to change the little front lights beside the main front light


Side Marker Lights
  1. If visible, remove the attaching screws and partially remove the front side marker light lens.
Fig. 7: To change a side marker bulb with no attaching screw, protect the body with a rag and gently pry the lens assembly outward . . .





Fig. 8: . . . until the entire assembly is free of the body and access to the bulb socket is achieved


2d8805f.jpgde76af4.jpg

Aug 30, 2009 | 1994 Mazda 323

1 Answer

Side Marker Bulbs


you need to remove entire assembly to access bulbs.it is secured by small hex head screws & a ''sliding tab'',an L shaped piece you pry up w/a flat screwdriver.

Jul 30, 2009 | 2005 Mercury Mariner

1 Answer

Scion XB 2006,cant find replacement for side marker light assembl


Last resort, the dealer if any can order one for you.

May 25, 2009 | 2007 Scion xB

1 Answer

How to replace front turn light bulb on Caddy SRX 2004?


  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
    1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
    2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
    3. Pull the headlamp assembly out and away from the vehicle
    4. Disconnect the headlamp electrical connector.
    5. Remove the headlamp assembly from the vehicle.
    6. Remove the headlamp bulb cover from the headlamp assembly.
    7. Remove the headlamp bulb socket from the headlamp assembly.
    8. Remove the headlamp bulb.
    9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
    10. Remove the side marker bulb.

Feb 12, 2009 | 2006 Cadillac SRX

1 Answer

Headlight bulb replacement & side marker light bulb replacement


i think there are two flat guide pins that hold the headlight assembly in .. just pull them straight up ..and the assembly should come out ..hencse replace the bulbs.

Nov 15, 2008 | 1999 Pontiac Bonneville

Not finding what you are looking for?
2009 Mitsubishi Outlander Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...