Question about 1952 MG TD

Open Question

Need 1250cc head torque chart

Rebuilding engine

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the Torque for the head bolts on a Mitsubishi Lanser 2005 model 2 L motor


Here is a link to a pdf head bolt torque chart, it doesn't give pounds but degrees of rotation, you will need new head bolts as they are what is called torque to yield, they stretch. Yoour engine is on page 40 of the pdf. file. http://olybrake.com/pdf/fel_pro_torque_specs_guide.pdf

May 21, 2016 | Mitsubishi Cars & Trucks

1 Answer

2005 corolla head bolt torque


A Chiltons/Haynes repair manual from your local auto parts store that covers your year/make/model has all of your answers under the "engine rebuild" heading.

Sep 23, 2014 | 2005 Toyota Corolla

1 Answer

What are engine torque specs


witch engine go to autozone or similar parts house and ask for them to print the torque spects for that engine

Aug 22, 2014 | Cars & Trucks

1 Answer

TOYOTA HILUX 2006 engine head torque specs


it depends on the size of the screws. i recommend to set torque as 100lbs for new bolts, 90 for old bolts

Feb 29, 2012 | 2006 Toyota Hilux 3.0

1 Answer

Torque specs for 3.9l engine cylinder head and crankshaft bolts.


Page 3-26 of Chilton's reads:
14. Using no sealer whatsoever, install the new head gasket(s) to the block. Clean, dry and lightly oil all head bolts threads. Install the heads and install the head bolts.

Tighten head bolts in sequence to 50 ft. lbs. (68Nm). Repeat the sequence retightening the bolts to a final torque of 105 ft. lbs. (143 Nm) and repeat the second step to ensure that all bolts are accurately torqued.

torgue chart from chilton (page 3-11) for your engine and year show:
main bearing bolts 85 ft lbs
rod bearing bolts 45 ft lbs
crankshaft damper bolts 135 ft lbs
flywheel bolts 55 lbs

Mar 27, 2011 | 1992 Dodge Dakota

1 Answer

Need to know how much torque to tighten head bolts and connectingrods


If you are repairing the engine to this level, a bottom or top rebuild, you should already have a chiltons. If not, what are you doing?! These specifications along with many necessary others should be in your repair manual unless you are just gathering this information for fun. Sorry about the lecture, but if you don't have torque specs for this, what else do you not have. Not only do you need the torque specs but each head bold needs to be torqued in a certain sequence as well. Head bolts are torqued in specific order gradually bringing the cast iron head to specification over three torque sessions.

Jan 22, 2011 | 1988 Jeep Cherokee

2 Answers

NEED FORD 2.2l head gaskets torque chart


Tighten the head bolts 29 to 32 ft lbs , then tighten again to 59 to 64 ft lbs

Apr 17, 2010 | 1989 Ford Probe

1 Answer

Torque specs for mighty max


Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

Oct 12, 2009 | 1991 Mitsubishi Mighty Max

1 Answer

Ford Fiesta Firefly 1250cc 2004\r\Head gasket blown?


it sounds like the head gasket is blown, unfortunately head could also be warped. and yes a garage is going to cost quite a bit

Aug 31, 2009 | 2005 Ford Focus

1 Answer

Auto box issue


I have an applicator chart that says 1992-1996 Diamante only had 3.0 ltr engine available,and the chart also says that the 3.5ltr was only available from 1997-2004.So either my chart is wrong,or you have a LATE 1996 that is actually a 1997.Either way,my chart says the 3.0 ltr engines used an F4A33-1 auto trans and the 3.5ltr's used an F4A51 trans.You ust recheck your vehicle to verify all the specifications.I would rebuild the trans that's in there,but i am a transmission rebuilder.Getting a used trans is kind of iffy,as you may be getting junk or a high mileage trans.As far as interchange,contacting a junkyard is the best way to go as they have interchange manuals.I would try and stay with the same year model and same vehicle.My chart says that the F4A51 also came in 96-05 Eclipse's...will it work in your Diamante?I don't know.I do know that an 05 trans won't work in your 96 model. Best way to go is rebuild your trans,or get one from a remanufacturer like Jasper Engines and Transmissions.

Jul 19, 2008 | 1997 Mitsubishi Diamante

Not finding what you are looking for?
1952 MG TD Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top MG Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

littlechum55

Level 1 Expert

19 Answers

Vernon Taylor

Level 3 Expert

2910 Answers

Are you a MG Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...