Question about 1999 Mitsubishi Mirage

Open Question

1999 mirage high pressure fuel hose connection

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Gas smells on my 1999 ford van windstar


Follow the fuel line to the engine. Look over the fuel rails and fuel connections looking for any cracks or breaks.

Oct 23, 2014 | 1999 Ford Windstar

1 Answer

Oil pressure


no lower then 15psi at idle and maybe about 50 to 80 while running. The high number is flexible, but it should never get lower then say about 15psi ever.

Sep 23, 2013 | Mitsubishi Mirage Cars & Trucks

2 Answers

1999 Mazda 626 V6 Car has an high idle and when running continues to **** off and drive itself if foot is not on the brake. HELP Please!!!!


Sounds like you have a bad fuel pressure regulator.First pull the vacuum hose off of the pressure regulator and look for fuel if any fuel runs out of it replace the regulator.Then if no fuel ran out, hook a fuel gauge to fuel rail and start engine and look at gauge reading and then pull the vacuum hose off and gauge reading should jump up 5-10 psi if it does'nt replace regulator.

May 04, 2011 | 1999 Mazda 626

1 Answer

Can high pressure fuel line be replaced with rubber hose


It is not recomended for the pressure will leak at the ends eventually. It is ok to use for emergency use for a day or two if the clamps are securely tighten well but not super tight

Apr 10, 2010 | 1999 Buick Regal

1 Answer

How to remove fuel filter housing 97 ford f-350


FIRST YOU NEED A SUITABLE CONTAINER.PLACE UNDER FILTER DRAIN HOSE OPEN THE FILTER DRAIN.NOW YOU HAVE TO REMOVE THE TURBOCHARGER ASSEMBLY.REMOVE THE THE BAFFLE AND THE AIR INLET CROSSOVER MANIFOLD.REMOVE THE TWO CAPSCREWS SECURING THE FUEL FILTER BASE TO THE CRANLCASE.DISCONNECT THE WATER DRAIN HOSE FROM FILTER. DISCONNECT THE FUEL OUTLET HOSE LOCATED BETWEEN THE FUEL AND FILTER HOUSING.AND THE FUEL RETURN HOSE FROM THE FUEL PRESSURE REGULATOR VALVE.DISCONNECT THE TWO FUELSUPPLY HOSES THAT CONNECT THE REGULATOR BLOCK TO THE CYLINDER FUEL RAILS.LOOSEN THE CLAMP AT THE FUEL PUMP END OF THE HOSE WHICH CONNECTS THE FUEL FILTER TO THE INLET OF HIGH PRESSURE STAGE AT THE FUEL PUMP.DISENGAGE THE WIRING HARNESS FROM THE RIGHT SIDE OF THE FILTER HOUSING.DISENGAGE THE ELECTRICAL CONNECTIONS FROM THE WATER IN FUEL SENSOR AND THE FUEL HEATER.REMOVE THE FUEL FILTER.USE A PRYBAR TO REMOVE THE FUEL FILTER CAP AND THE FILTER ELEMENT WILL COME OUT WITH THE CAP.DEPRESS THE ELEMENT LOCKING TABS AND REMOVE THE ELEMENT FROM THE CAP.TO INSTALL CLEAN THE MATING SURFACES AND INSTALL THE FILTER ELEMENT ONTO THE CAP MAKING SURE THE TABS ENGAGE.INSTALL THE FILTER CAP AND PRESS DOWN FIRMLY BUT GENTLY TO ENGAGE IT.ENGAGE THE WIRING CONNECTIONS TO THE FUEL HEATER AND WIF SENSOR.ENGAGE THE WIRING HARNESS TO THE FILTER HOUSING.TIGHTEN THE CLAMP AT THE FUEL PUMP END OF HOSE WHICH CONNECTS THE FUEL FILTER TO THE INLET OF HIGH PRESSURE STAGE AT THE FUEL PUMP.ENGAGE THE TWO FUEL SUPPLY HOSES THAT CONNECT THE REGULATOR BLOCK TO THE CYLINDER HEAD FUEL RAILS.CONNECT THE FUEL OUTLET HOSE LOCATED BETWEEN THE FUEL AND FILTER HOUSING AND THE FUEL RETURN HOSE FROM THE FUEL PRESSURE REGULATOR VALVE.CONNECT THE WATER DRAIN HOSE TO THE FILTER.INSTALL THE 2 CAP SCREWS SECURING THE FUEL FILTER BASE TO THE CRANKCASE.INSTALL THE AIR INLET CROSSOVER MANIFOLD AND BAFFLE.INSTALL THE TURBOCHARGER ASSEMBLY.

Apr 03, 2010 | 1997 Ford F350 Crew Cab

1 Answer

CHANGE FUEL PUMP ON 1999 BLAZER


Check your fuel pressure.
Hopefully this tank is not full, as you need to pull the tank to change fuel pump, this is mounted onto the tank through the top. There are several plastic fitting and hose connecitons on the tank as well as the fuel level connector. There may also be a Vapor pressure sensor on the tank. After unbolting the tank lower the tank just far enough to remove the wireing and hoses. Make sure top of tank is clean. If you have to move tank out from under Blazer cover hose aconnectionss and wash off top of tank and flange area. Unlock flange and R and R pump assembly. Reconnect hoses and wires, reinstall tank. Connect hose to fuel test port on engine, purge air from fuel system. Check the fuel pressure. InMrFixIt

Dec 29, 2009 | 1999 Chevrolet Blazer

2 Answers

Fuel pump relay for 2000 mitsubishi mirage


most newer veichles your feul pumps in your gas tank

Aug 22, 2009 | 1993 Mitsubishi Mirage

2 Answers

What is EVAPORATIVE EMISSION...Purge Flow?? Mitsubishi Mirage?


This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. Try changing the gas cap first then check the rubber hoses that are visble on top of the engine. Vote "Yes" for me!

Aug 18, 2009 | 1999 Mitsubishi Mirage

3 Answers

Wheres the fuel filter on my 1987 mitsubishi mighty max


Hi Paulvilla13,

I'm not sure if your '87 is the same as my '88 or not, but mine is located just in front of the tank. I also have to remove the rear driver-side wheel to get at it.

Hope I've helped, don't forget to rate.

Lazaruselite

Feb 24, 2009 | 1987 Mitsubishi Mighty Max

Not finding what you are looking for?
1999 Mitsubishi Mirage Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...