Question about 1999 Ford Escort

1 Answer

Air bag have a beeping sound indicating the air bag

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,991 Answers

Common fault on FORD

Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.


Just push it together properly and it should clear the AirBag fault


Posted on Sep 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 lincoln town car air bag light is on 5 beeps 5 times


The five beeps - five times would indicate a code 55 , but factory service info only goes to code 53 .

  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.

Did your air bag light flash at all ? Apparently this will do flash the air bag light codes as well .
Symptom Chart Condition Possible Sources Action
  • Air bag warning indicator is illuminated continuously
  • Fuse
  • Damaged wiring, terminals or connectors
  • A faulty diagnostic connector
  • A faulted RCM
  • A faulty instrument cluster
  • Go To Pinpoint Test A .
  • Air bag indicator flashing
  • Air bag/pretensioner supplemental restraint system (SRS) fault
  • REFER to DTC Priority Table.
  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.
  • No communication with the restraints control module (RCM)
  • Fuse
  • Diagnostic tool
  • Data link connector (DLC)
  • A faulted RCM
  • Circuitry
  • Go To Pinpoint Test V .
LFC - light flash codes .
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Table
DTC a LFC b Description Action To Take - Continuous The Air Bag Indicator is Illuminated Continuously, RCM Disconnected or Inoperative, Loss of Battery Feed, or Loss of Signal Ground Go To Pinpoint Test A . B1231 13 Crash Data Memory Full Install a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment . B1317 Continuous Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to Section 414-01 . B1318 Continuous Battery Voltage Low CHECK battery voltage; to be above 9.0 volts. REFER to Section 414-01 . B1342 12 RCM Is Faulted Install a new RCM. B1869 NONE
Continuous lamp
Secondary air bag warning sounds if another fault is present Lamp Air Bag Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test B . B1870 NONE
Secondary air bag warning sounds if another fault is present Air Bag Warning Indicator Circuit Short to Battery Go To Pinpoint Test C . B1891 53 Air Bag Tone Warning Indicator Circuit Short to Battery Go To Pinpoint Test D . B1892 53 Air Bag Tone Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test E . B1921 14 Air Bag Diagnostic Monitor Ground Circuit Open Go To Pinpoint Test F . B2292 33 Restraint System - Safety Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test G . B2292 34 Restraint System - Safety Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test G . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2294 24 Restraint System - Curtain Fault (Driver Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2294 25 Restraint System - Curtain Fault (Passenger Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2295 22 Restraint System - Side Air Bag Fault (Driver Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2295 23 Restraint System - Side Air Bag Fault (Passenger Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault (Front Impact Severity Sensor Circuit Fault) Go To Pinpoint Test K . B2296 43 Restraint System - Impact Sensor Fault (Driver Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 45 Restraint System - Impact Sensor Fault (Driver Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 44 Restraint System - Impact Sensor Fault (Passenger Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 46 Restraint System - Impact Sensor Fault (Passenger Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2434 51 Driver Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test L . B2435 51 Driver Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test M . B2438 52 Passenger Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test N . B2439 52 Passenger Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test O . B2477 Continuous Module Configuration Error INSTALL a new RCM. B2691 51 Driver Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test P . B2692 52 Passenger Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test Q . C1414 15 Incorrect Module Design Level Go To Pinpoint Test R . C1947 49 Driver Seat Track Position Sensor Circuit Short to Ground Go To Pinpoint Test S . C1948 49 Driver Seat Track Position Sensor Circuit Resistance Out Of Range Go To Pinpoint Test T . C1981 49 Driver Seat Track Position Sensor Circuit Fault Go To Pinpoint Test U . - - No Communication with the Restraints Control Module Go To Pinpoint Test V . Your best bet have codes checked with a scan tool .

Jan 23, 2017 | Lincoln Cars & Trucks

1 Answer

Truck beeps 5 beeps 5 times in a row every time i start it


Check to see if your Air Bag warning light comes on to prove out when you turn the key to the "on" position. If it does not the beeping you are hearing is an audible air bag warning indictator indicating a fault in the system.

Sep 25, 2014 | 1999 Ford Ranger SuperCab

1 Answer

Why the air bags make a warning sound beep


Need to get it to a reputable repair shop. Have them check for fault code in restraint system. You're getting a code 15 that's telling you there's a concern with the drivers side air bag, module, wiring, or component failure. Possibly a clockspring but that's only a guess. If you were to get in an accident the bags would not deploy, when module sees a fault it shuts down the system to prevent false air bag depl

Jun 29, 2014 | 2000 Ford Expedition

1 Answer

Where is the switch to disable the passenger airbag on a 2003 ford taurus


Supplemental Restraint System (SRS) Depowering and Repowering

Depowering Procedure

WARNING: Always wear safety glasses when repairing an air bag supplemental

restraint system (SF3) vehicle and when handling an air bag module. This will reduce

the risk of injury in the event of an accidental deployment.

WARNING: Never probe the connectors on the airbag module. Doing so can result in

air bag deployment, which can result in personal injury.

WARNING: To reduce the risk of personal injury, do not use any memory saver

devices.

NOTE: Ifa seat equipped with a seat mounted side airbag and or a safety belt

pretensioner (if equipped) system is being serviced, the supplemental restraint system

(SES) must be depowered.

NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the

ignition switch is ON. This is normal operation and does not indicate a supplemental

restraint system (SRS) fault.

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle

to the customer

1. Turn all vehicle accessories OFF.

2. Turn the ignition switch to OFF.

3. At the central junction box (Cm), located below the LH side of the instrument panel,

remove the cover and the restraints control module (RCM) fuse F223 (lOA) from

the CTh. For additional information, refer to the Wiring Diagram Manual.

4. Turn the ignition ON and visually monitor the air bag indicator for at least 30

seconds. The air bag indicator will remain lit continuously (no flashing) if the correct

ROsI fuse has been removed, If the air bag indicator does not remain lit

continuously, remove the correct RCM fuse before proceeding

5. Turn the ignition switch to OFF.

6. WARNING: To avoid accidental deployment and possible personal injury, the

backup power supply must be depleted before repairing or replacing any front or

side air bag supplemental restraint system (SRS) components and before set-ricing,

replacing, adjusting or striking components near the front or side air bag sensors,

such as doors, instrument panel, console, door latches, strikers, seats and hood

latches.

To deplete the backup power supply energy, disconnect the battery ground cable

and wait at least one minute. Be sure to disconnect auxiliary batteries and power

supplies (if equipped).

Disconnect the battery ground cable and wait at least one minute.

Repoweri.ng Procedure

1. WARNING: The restraint system diagnostic tool is for restraint system service

only. Remove from vehicle prior to road use. Failure to remove could result in

injury and possible violation of vehicle safety standards.

Make sure all restraint system diagnostic tool(s) that may have been installed during

the repair have been removed from the vehicle and all SRS components are

connected.

2. Turn the ignition switch from OFF to ON.

3. Install the ROsI fuse F2.23 (lOA) to the DB and install the cover.

4. WARNING: Be sure that nobody is in the vehicle and that there is nothing

blocking or set in front of any air bag module when the battery ground cable is

connected.

Connect the battery ground cable.

5. Prove out the supplemental restraint system (SRS) as follows:

Turn the ignition key from ON to OFF. Wait 10 seconds, then turn the key back to

ON and visually monitor the air bag indicator with the air bag modules installed. The

air bag indicator will light continuously for approximately six seconds and then turn

off. If an air bag supplemental restraint system (SF3) fault is present, the air bag

indicator will:

- failto light.

- remain lit continuously.

- flash.

The flashing might not occur until approximately 30 seconds after the ignition switch

has been turned from the OFF to the ON position. This is the time required for the

restraints control module (RCM) to complete the testing of the SRS. if the air bag

indicator is inoperative and a SRS fault exists, a chime will sound in a pattern of 5

sets of 5 beeps. If this occurs, the air bag indicator and any SRS fault discovered

must be diagnosed and repaired.

Jan 12, 2011 | 2003 Ford Taurus

1 Answer

Hello I saw the break alert light lit on my


Usually when th fluid level low light comes on, it is because the fluid is ging to the front calipers to fill the pistons that push the brake pads against the rotors. This is because the pads are worn down and probably need replacing.

As for the 3 beeps, it is not related to the brakes.

if it is 5 beeps, it is the air bag or pretensioner.

When the ignition is cycled (turned off and then on), the air bag indicator will remain lit for six seconds and then go out. If an SRS fault exists, the air bag indicator will then flash the two-digit LFC. The air bag indicator will flash the LFC five times, then it will remain illuminated for the rest of the key cycle. The RCM will also communicate the current and historical DTCs through the data link connector (DLC), using the scan tool. If the air bag indicator does not function, and the system detects a fault condition, the RCM will signal the GEM to activate an audible chime. The chime is a series of five sets of five tone bursts. If the chime is heard, the SRS and the air bag indicator require repair.

Mar 02, 2010 | 2002 Ford Ranger Regular Cab

2 Answers

Dash lights went out, so i had some fuses removed to see which one was bad. next thing i know the airbag light was on.


You just need to turn it off again. You created a false trigger of the light. You may have to have dealer do it with scan tool.


Prove Out Procedure
Turn the ignition switch from the OFF to the RUN position and visually monitor the air bag indicator with the air bag modules or restraint system diagnostic tools installed. The air bag indicator will light continuously for approximately six seconds and then turn off. If an air bag supplemental restraint system (SRS) fault is present, the air bag indicator will either:
  • fail to light.
  • remain lit continuously.
  • flash.
The flashing might not occur until approximately 30 seconds after the ignition switch has been turned from the OFF to the RUN position. This is the time required for the restraints control module (RCM) to complete the testing of the SRS. If the air bag indicator is inoperative and an SRS fault exists, a chime will sound in a pattern of five sets of five beeps. If this occurs, the air bag indicator will need to be repaired before diagnosis can continue.
----------------------------------------------------------- Restraints Control Module (RCM)
The restraints control module (RCM) performs the following functions:
  • signals the inflators to deploy the air bags in the event of a deployable crash.
  • monitors the air bag supplemental restraint system (SRS) for faults.
  • illuminates the air bag indicator if a fault is detected.
  • flashes the air bag indicator to indicate the lamp fault code (LFC) detected.
  • communicates through the data link connector (DLC) the current or historical diagnostic trouble codes (DTCs).
  • signals the generic electronic module (GEM) to activate a chime if the air bag indicator is not available and another SRS fault exists.
NOTE: The safing sensor is internal to the RCM and is not repaired separately.
The RCM monitors the SRS for possible faults. If a fault is detected while the ignition switch is in the RUN position, the RCM will illuminate the air bag indicator located in the instrument cluster.
When the ignition is cycled (turned off and then on), the air bag indicator will begin its prove out sequence. During prove out the air bag indicator will illuminate for six seconds, go off for two seconds and then, if a system fault exists, flash the two-digit LFC. The air bag indicator will flash the LFC five times, then it will remain illuminated for the rest of the key cycle. The RCM will also communicate the current and historical DTCs through the DLC, using a scan tool. If the air bag indicator does not function, and the system detects a fault condition, the RCM will signal the GEM to activate an audible chime. The chime is a series of five sets of five tone bursts. If the chime is heard, the SRS and the air bag indicator require repair.
LFCs are prioritized. If two or more faults occur at the same time, the fault having the highest priority will be displayed. After that fault has been corrected, the next highest priority fault will be displayed.
The RCM includes a backup power supply. This feature provides sufficient backup power to deploy the air bags in the event that the ignition circuit is damaged in a collision before the safing and air bag sensors determine that deployment is required. The backup power supply will deplete its stored energy approximately one minute after the battery ground cable is disconnected.
Electrical System
The electrical system that supports the air bag supplemental restraint system (SRS):
  • is powered from the battery through the ignition circuit.
  • provides the electrical path from the restraints control module (RCM) to the air bag modules.
  • provides the electrical path from the RCM to the air bag indicator.
  • provides the electrical path from the RCM to the data link connector (DLC).
  • provides the electrical path from the RCM to the generic electronic module (GEM).
----------------------------------------------------------
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Priority Table DTC a LFC b LFC Priority Description Action To Take — — 1 The Air Bag Indicator is Illuminated Continuously — RCM Disconnected, Inoperative, or Lost/Low Ignition Feed Go To Pinpoint Test A . B1342 24 2 RCM Is Faulted INSTALL a new RCM. B1231 19 3 RCM Crash Data Memory Full INSTALL a new RCM. B1921 21 4 RCM Bracket Ground Resistance High Go To Pinpoint Test B . C1414 29 5 Incorrect Vehicle Identification Code Go To Pinpoint Test C . B1887 15 6 Driver Air Bag Circuit Shorted to Ground B1916 15 7 Driver Air Bag Circuit Shorted to Battery or Ignition B1888 16 8 Passenger Air Bag Circuit Shorted to Ground B1925 16 9 Passenger Air Bag Circuit Shorted to Battery or Ignition B1932 32 10 Driver Air Bag Circuit Resistance High B1933 33 11 Passenger Air Bag Circuit Resistance High B1934 34 12 Driver Air Bag Circuit Resistance Low B1935 35 13 Passenger Air Bag Circuit Resistance Low B1892 — 17 Air Bag Tone Warning Indicator Circuit Shorted to Ground or Open B1891 — 18 Air Bag Tone Warning Indicator Circuit Shorted to Battery or Ignition B1869 Tone c 19 Air Bag Indicator Inoperative B1870 Tone c 20 Air Bag Indicator Shorted to Battery — — — No Communication with the Restraints Control Module

Feb 24, 2010 | 2004 Ford Mustang

1 Answer

5 series' of 5 beeps in a row on start up


Check the Air Bag Indicator Light. When you turn the car on it should stay on for 6 seconds and then turn itself off. If a fault is detected in the system operation check, the indicator light will either fail to light, stay on continuously or flash. The flashing may not start until up to 30 seconds after the initial systems check.

If there is a fault in the system AND the air bag indicator light fails to light then an audible tone will alert you- it will be a set of 5 chimes (bells/beeps) five times in a row.

Have the Air Bag serviced and the indicator light bulb changed. Since the dash will be off in order to change the bulb, I would have all of the other dash lights changed at the same time. If one goes out, others will surely follow.

Good luck!

Corri R. / Service Writer

Jan 26, 2009 | 2002 Mazda Tribute

1 Answer

1999 f150 airbag light stays on after blinking upon start up!


Passenger Air Bag Deactivation (PAD) Switch
The passenger air bag deactivation (PAD) switch:
  • is located on the instrument panel to the right of the climate controls.
  • contains a light emitting diode (LED) that indicates when the PAD switch is activated (passenger air bag disabled).
  • allows the passenger air bag deployment circuit to be disabled using the ignition key.
  • should be used whenever a child safety seat is being used in the front passenger seating position.
------------------------------------------------------------------------------------------
Prove Out the System
Prove out the system means to turn the ignition switch from the OFF to the RUN position and visually monitor the air bag indicator with the air bag modules installed. The air bag indicator will light continuously for approximately six seconds and then turn off. If an air bag supplemental restraint system (SRS) fault is present, the air bag indicator will either:
  • fail to light.
  • remain lit continuously.
  • flash.
The flashing might not occur until approximately 30 seconds after the ignition switch has been turned from the OFF to the RUN position. This is the time required for the restraints control module (RCM) to complete the testing of the SRS. If the air bag indicator is inoperative and an SRS fault exists, a chime will sound in a pattern of five sets of five tone bursts. If this occurs, the air bag indicator will need to be repaired before diagnosis can continue.
----------------------------------------------------------------------------------------
Active Commands
This command allows the technician to verify operation of the air bag indicator, passenger air bag deactivation (PAD) lamp and chime. When the air bag output command is executed, the indicator, the PAD lamp, chime and the chime are activated simultaneously for approximately four seconds. All devices are deactivated automatically.

Jan 15, 2009 | 1999 Ford F150 Regular Cab

1 Answer

I changed the steering coloumn and my airbag light flashes


clockspring is behind steering wheel.

info

96 escort

If the computer in the air bag diagnostic monitor detects an open in the air bag indicator circuit and if another system fault exists, then the air bag diagnostic monitor will turn on its internal tone generator (beeper). The beep pattern is five sets of five beeps. The pattern is repeated every 30 minutes while the ignition switch is in the ON position. The five beeps do not indicate a code five or any other code. The air bag indicator circuitry must be repaired before the diagnostic trouble code can be read.

Jan 07, 2009 | 1995 Ford Escort

1 Answer

Strange beeping noise


I read on another site that if the indicator on the dash is malfunctioning and there's a fault code in the system, the beeping is a secondary indication that there's a need for service. I've had my air bag light blinking for some time now. Yesterday my gauges went out, Oil Pressure, Gas Level, Temp Level, and the Battery Charging Meter, all went dead. After starting the vehicle, it beeps 5 sets of 5 beeps. Since the dash obviously has problems, (Including the Air Bag blinking thing not working), the beeps I now hear are what you are experiencing. However, if you still see the air bag light blinking, maybe your situation is a bit different than mine.

Jul 22, 2008 | 1994 Ford Aerostar Extended

Not finding what you are looking for?
1999 Ford Escort Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4382 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...