Question about 2011 Saab 9-5

Open Question

2011 saab 9-5 cam actuator bank 1 - 2011 Saab 9-5

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a csmshsft sensor on a 2008 cadillac srx


Before you replace a part you may or may not need . Why ? What code ? Does the vehicle run ? There has been a lot of confusion on these vehicles with variable valve timing , mixing up cam sensors with camshaft actuators
DTC P0008: Engine Position System Performance Bank 1

DTC P0009: Engine Position System Performance Bank 2
The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).


?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.



DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2

DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .

Jul 24, 2016 | 2008 Cadillac Srx

1 Answer

P0014 on bmw 525i


Code P0014 "B" Camshaft Position - Timing Over-Advanced ...

www.obd-codes.com/p0014
Detailed information on troubleshooting and repairing a p0014 dtc diagnostic trouble code which refers to a camshaft position actuator circuit.Missing: 525i

Error Code P0014 - Bimmerfest - BMW Forums

www.bimmerfest.com > ... > 5 Series > E39 (1997 - 2003)

Jan 9, 2011 - 9 posts - ‎5 authors
Error Code P0014 E39 (1997 - 2003) ... Join Date: Nov 2010. Posts: 3. Mein Auto: X5,525i ... As an aside, I used BMW OEM parts. Thanks for ... 530i Error P0014
1 post
Sep 12, 2011
Code P0014 nightmare
18 posts
Jan 7, 2011
2001 bmw 525i p0014
3 posts
May 29, 2010
P0015, P0014 Codes: Intake cam sensor? Vanos ...
25 posts
Jan 20, 2010
More results from www.bimmerfest.com

Dec 29, 2015 | BMW Cars & Trucks

1 Answer

Where is the fuel relesase door button in a 2011 saab 9-5


should be on the drivers door have attached a picture
saab-9-5-hirsch-carbon-leather.jpg

May 22, 2014 | 2011 Saab 9-5

2 Answers

Code p0014 exhaust and code p0015 exhaust


The code P0014 is for Camshaft Positon Sensor Actuator Bank 1. The possible causes are incorrect camshaft timing, wiring problems (harness/wiring) in intake timing control valve solenoid system; continuous oil flows to VCT piston chamber or failed timing valve control solenoid(stuck open).
The code P0015 is for Camshaft Position -Timing Over-******** (Bank 1). Your problem will probably be that the timing will be slightly out, due to wear (stretch) of the timing chain; this will all be linked to the overall cold start issue and the timing position. Get that timing checked, or push for the full fix for the cold start timing issue.

Jul 25, 2013 | 2007 Mini Cooper

1 Answer

Check engine light code p0014 exhaust and p0015 exhaust


P0015: Camshaft Position, Act B - bank 1, timing over

P0014: Camshaft Position, Act B - bank 1, timing over advanced
Check oil level and quality.
Remove n clean exhaust camshaft vanost actuator.
Do not refit to exhaust cam, but swap with inlet actuator.
clear codes...if eml on again see if fault moved to inlet cam. If so replace the actuator.

Jul 25, 2013 | 2007 Mini Cooper

1 Answer

IDLE CONTROL SYSTEM!! HELP


Poss clogged injector, vacuum leak Throttle body gasket Good luck

Mar 29, 2017 | 2003 Saab 9-3

1 Answer

What does the code A13 mean on my Acura 2005 TL


Camshaft position actuator B- bank 1 curcuit malfunction.. 3 things will cause this, Bad cam actuator, loose or broken wire to the actuator, bad ECM. As for the yearof your car, my guess would be the cam actuator, but I would rule out the wiring first.

Feb 07, 2011 | 2005 Acura TL

2 Answers

Ml350 replaced a/b cam position sensor reset computer & and erra codes p0016/p0016 check engine ligth is reset car drives with light off when engine is turn off and started the light goes out if you...


P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

Nov 02, 2010 | Mercedes-Benz ML350 Cars & Trucks

1 Answer

Code po113 on 2003 ford zx2 how to get it off and how to fix


Number P0013 Description "B" Camshaft Position - Actuator Circuit/Open
Type: Powertrain - Fuel and Air Metering - ISO/SAE Controlled

Location Bank 1
Notes The "B" camshaft shall be either the "exhaust," "right," or "rear" camshaft. Left/Right and Front/Rear are determined as if viewed from the driver's seating position. Bank 1 contains cylinder number one, Bank 2 is the opposite bank.

The cam actuator is the one that makes possible the retarding and advancing of the Cams..
You must have a cam actuator harness problem or an electric failure in the internal actuator, check if the actuator harness and wires are not broken, check if they are receiving good voltage, If they are good, you almost have a failure in the actuator and you will have to replace it.....

Feb 15, 2010 | Ford Escort Cars & Trucks

Not finding what you are looking for?
2011 Saab 9-5 Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...