I lose the harnesses license lights in the bumper of my rabbit 2009..

To remove the bumper cover on a 2002 Cadillac Escalade to access the license plate assembly, you'll need some basic tools and follow these steps:
**Note:** Be sure to take necessary safety precautions, and if you're uncomfortable doing this yourself, consider consulting a professional mechanic.
1. **Gather Tools and Materials:**
- Screwdrivers
- Socket set
- Pliers
- Trim removal tool (or flathead screwdriver)
2. **Raise the Vehicle:**
- For easier access, you can raise the front end of your vehicle using a jack and support it with jack stands.
3. **Remove the Wheel Well Liners (Optional):**
- Depending on your vehicle and access, you may need to remove the wheel well liners to reach the bumper attachment points. These are typically held in place with plastic clips or screws.
4. **Remove Retaining Clips and Screws:**
- Locate and remove the screws, clips, or fasteners holding the bumper cover in place. These are typically found along the top and sides of the bumper.
- Use a trim removal tool or a flathead screwdriver to carefully pry out the clips.
5. **Disconnect Fog Lights (if applicable):**
- If your vehicle has fog lights integrated into the bumper cover, disconnect the wiring harnesses.
6. **Detach the Bumper Cover:**
- Carefully start detaching the bumper cover from the vehicle by gently pulling it away. Work your way around the bumper to release the clips or fasteners.
7. **Remove the License Plate Assembly:**
- Once the bumper cover is loosened, you should have access to the license plate assembly.
- Remove the screws or fasteners securing the license plate assembly, and detach it from the bumper cover.
8. **Install the New License Plate Assembly:**
- Attach the new license plate assembly to the bumper cover, using the same screw holes or fasteners.
9. **Reattach the Bumper Cover:**
- Align the bumper cover properly, and carefully push it back into place, making sure it clips securely.
10. **Reattach Retaining Clips and Screws:**
- Put back the screws and retaining clips in their respective locations along the top and sides of the bumper cover.
11. **Reconnect Fog Lights (if applicable):**
- Reconnect the wiring harnesses for the fog lights.
12. **Reinstall Wheel Well Liners (if removed):**
- If you removed the wheel well liners, reinstall them and secure them with the clips or screws.
13. **Lower the Vehicle:**
- Carefully lower your vehicle from the jack stands if you raised it.
Remember to take your time, work carefully, and document the disassembly process if necessary. If you're unsure about any step, it's always a good idea to consult your vehicle's repair manual or seek professional assistance.

There should be a pigtail connector for trucks with or without rear bumpers. Did you look in the harness for a brown wire ?
Same as the marker lights.

Look under the bumper, you should find the light bulbs in a harness. To release them, twist the bulbs until the are unlocked from the harness. Pull the bulb out and replace it.

Look behind the bumper for where the bulbs are located. Unlock the bulbs by twisting them loose. Pull the bulb out of the harness and unscrew the bulb. Replace it and lock the bulb back into the harness.

1. Remove the screws that secure the license plate lamp assembly to the rear bumper fascia
2. Pull the license plate lamp assembly down and out through the mounting hole in the rear bumper fascia far enough to access and disconnect the wire harness connector.
3. Remove the license plate lamp assembly from the rear bumper fascia.

just screw it into the bumper it wont hurt anything

one of your lights must be out.. check the sidemarkers on the bumper, or the tail lights. or maybe the small parking lights in the headlight.

Just reach behind the bumper and grab the light/electrical harness and twist is either way and then it should pull out put in a new 194 bulb and you are set.

Try link below, may point you in right direction, but you'll have to scroll down & find what you need. Otherwise I'd start from bumper with test light & work my way back toward front harness, after all fuses, plugs etc been checked.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800610de

The fuel pump sending unit may be bad or disconnected.Its located on the fuel pumps.