Question about Dodge Pickup

Open Question

Have code p0382 1999 turbo cummins 3500 diesel 5.9L

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 29 Answers

SOURCE: Charging problem on 1996 Dodge Ram 3500 Cummins Turbo Diesel

I had the same problem on a 94 dodge with the cummins. It seems the crank sensor that reads from a notch on the harmonic balancer was the problem Without this sensor reading that the engine is running the alternator wont charge. Possibly the same problem with yours

Posted on May 03, 2009

Ad
blueextc3221
  • 15935 Answers

SOURCE: have ram 3500 laramie mega cab 4x4 with 6.7-liter

Technical Description:
EVAP Control System Canister Vent Solenoid Circuit Malfunction
The EVAP system monitors the canister vent (CV) solenoid circuit for an electrical failure.
The test fails when the signal moves outside the minimum or maximum allowable calibrated parameters for a specified canister vent duty cycle by PCM command.
Symptoms: You will likely not notice any drivability problems.
Causes: A code P1451 may mean that one or more of the following has happened:
*VPWR circuit open
*Damaged canister vent solenoid
*Canister vent solenoid circuit open or shorted to ground, power, etc.
*Damaged Powertrain Control Module (PCM)
*Possible SolutionsVerify canister vent solenoid - To verify normal functioning, monitor the EVAP canister vent solenoid signal PID EVAPCV and the signal voltage
(PCM control side).With the valve open, EVAPCV indicates 0% duty cycle and a voltage approximately equal to battery voltage.
When the valve is commanded fully closed, EVAPCV indicates 100% duty cycle, and a minimum voltage drop of 4 volts is normal.
Output test mode may be used to switch output on/off to verify function.
*Replace canister vent solenoid

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question$$$$

Posted on Sep 29, 2010

  • 1 Answer

SOURCE: 2001 dodge ram 3500 cummins 24v turbo diesel dtc

injector pump bad change it

Posted on Jan 27, 2011

  • 878 Answers

SOURCE: I cant find the fuel

its inside your gas tank

Posted on Apr 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 GMC 4500 Diesel Truck - code P0039..At random intervals the engine will drop to idle and CEL illuminates. The throttle will not operate. what sensors I should replace and it what order? Thanks


Dodge Cummins Error Codes List - Diesel Bombers



www.dieselbombers.com > Dodge Cummins > Dodge Diesel Tech Articles

Apr 6, 2009 - It appears to have every CEL code known to man... or at least known to Dodge. ... Chevy/GMC Truck and Duramax Turbo Diesel Forum · Chevy/GMC Duramax... General · 2011 · 2013+ · 2007.5 - 2012 LMM · 2006 - 2007 LBZ .... P0039 Turbo/Super Charger Bypass Valve Control Circuit Range/Performance

Aug 23, 2015 | GMC Cars & Trucks

1 Answer

2006 Dodge ram 3500 Turbo Cummins diesel, air conditioning is cold but there is very little air pressure even when turned on high, fan sounds like it is blowing like crazy but very little air movement...


flap broke. common problem. drop motor at bottom of dash, uses 3 bolts, reach up, grab flab twist and pull down. put motor back on. takes 5 min or less

Jul 07, 2010 | 2006 Dodge Ram 3500 Truck

1 Answer

I have the following fault codes reading


P0216 - injector timing control circuit

P0234 - turbo / supercharger over boost condition

P0523 - engine oil pressure sensor / switch circuit high inout.

Jan 22, 2010 | 1998 Dodge Ram 3500 2WD

1 Answer

Number one injector bank on 2006 dodge cummins


you'll notice on your valve cover gasket there is two connectors.. the one up front is your 1-3 the one in the rear is your 4-6... you can remove your valve cover and check the connections from the injector connectors to the
connectors on the valve cover.. check for an open.. however you could also have a fault internally in 1 of your injectors in that bank as well.. hope this info helped..

Dec 08, 2009 | 2006 Dodge Ram 3500 Truck

1 Answer

Engine replacement


any of the non computerized aka 12 valve cummins will interchange going from the p7100 pump on the 94 to the ve injection pump on the 92 may mean rerouting some of the fuel lines to hook it up. make sure you use all the sensors from the 94 engine though so all your gauges read correctly other than the fuel system the engines are identical though so should have no issues doing this

Apr 27, 2009 | 1994 Dodge Ram 3500

3 Answers

Charging problem on 1996 Dodge Ram 3500 Cummins Turbo Diesel


I had the same problem on a 94 dodge with the cummins. It seems the crank sensor that reads from a notch on the harmonic balancer was the problem Without this sensor reading that the engine is running the alternator wont charge. Possibly the same problem with yours

Mar 25, 2009 | 1996 Dodge Ram 3500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...