Question about Mitsubishi Montero Sport

1 Answer

Battery light and brake light are on at idle when i rev the engine to 3000 the lights go off i just changed the altinater

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Mitsubishi Master
  • 803 Answers

Check for loose belt, slipping balancer, or wrong size alternator pulley(too big diameter)

Posted on Mar 18, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Holden rodeo 2003, wont rev over 3000rpm


run a scanner on the system to determine codes to diagnos problem

Apr 13, 2014 | 2003 Isuzu Rodeo

1 Answer

2004 chevy malibu high rpms and revving all by itself


Have the engine checked for vacuum leaks, that will cause a high idle speed. As a 35 year veteran of auto repair I can tell you that engine flushs are a 100% waste of your hard earned money.

Jan 27, 2014 | Cars & Trucks

1 Answer

Hi guys...my yaris is running rich, has poor gas mileage (360km on a full tank). and very slow and choppy idle (idles like a really old car) these are the things i have done so far : change air and fu


Do the following:
1. Clean the throttle body from inside.
2. Adjust the spark plugs gap to 1.00 mm.
3. Check fuel pump pressure. (44 Psi - 49 psi)
4. Remove the negative battery terminal for 5 minutes.
5. Connect the battery terminal.
6. Check the engine oil level and coolant level.
NOTE: Before starting the engine shut off all lights and loads for example room light, blower, radio, parking light etc.
7. Start the engine and hold the throttle at 3000 rpm till radiator fan comes on.
8. After the fan comes on release the throttle pedal and let it idle for 10 minutes.

May 08, 2012 | 2005 Toyota Yaris 1.3

1 Answer

Service Engine light is on, gas milage is poor getting est. 9mpg city (average 1990 dakota est. 20 mpg city) I put in a new airfilter in car, did a oil flush, changed oil and oil is still clean after 50...


if you have'nt replaced those spark plugs and wires lately, you need to.and also, lucas fuel treatment, in my personal opinion,is the very best for unclogging fuel lined and injectors.it being below a 1999 model and your check engine light is on, you can have it coderead for free if you're near anautozone or advance automotive parts store. they will code read it and tell you why that check engine lights coming on.hope this helps and thank you for choosing fixya.com

Nov 23, 2010 | 1990 Dodge Dakota

1 Answer

When brake is pushed engine idles irratic. take out the stop light fuse and its ok. Have you ever ran into this before?


more than likely you have a vacuum leak
get some carb cleaner
start car and let idle
spray carb cleaner around intake gaskets throttle body vacuum lines etc
if you notice a change in idle (revs up or stumbles) repair that part

Nov 22, 2010 | 1991 Toyota Pickup

1 Answer

How do i set the timming on 94 mercury villager van


you only set base timing to 15 degrees BTDC (before top dead center).

Ignition Timing
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Parking brake control should be applied.
    Depress the parking brake pedal, and warm the engine to the normal operating temperature.
  1. Turn off all electrical loads.
  1. Rev the engine to 2000-3000 rpm two or three times and allow the engine to return to the idle.
  1. Turn off the engine and disconnect the throttle position sensor electrical connector. (not really necessary)
  1. Start the engine and rev it to 2000-3000 rpm two or three times and allow the engine to return to the idle.
  1. Check the idle speed. The idle speed should be between 700-800 rpm in PARK (P) or NEUTRAL (N) position.
  1. NOTE: Make sure that the timing pointer is pointing to the 15° Before Top Dead Center (BTDC) mark on the crankshaft pulley. Each notch on the crankshaft pulley represents 5 degrees.
    Check the ignition timing with a timing light.
632206b.gif go here for villager help

http://autos.groups.yahoo.com/group/villagerquest/

Jun 09, 2009 | 2001 Mercury Villager

1 Answer

Engine light on wont go over 3000rpm or under 2000rpm


Try the IAC valve this regulates the idle.

May 22, 2009 | 1998 Mitsubishi Galant

1 Answer

Engine revs up even when parked - Honda Odessey 2002


replace the idle air control valve.(on the bottom of the throttle body) may be easier to remove the throttle body and turn in upside down to remove the idle air control valve and hoses. be sure not to pinch the gasket. after u do that be sure to replace any coolant that may have came out. then, start the car, rev the car to 3000 rpms till the radiator fan comes on , then let the vehicle idle for 20 - 30 mins . the computer should relearn the idle. local honda dealer should have the valve in stock,

Apr 04, 2009 | 2002 Honda Odyssey

1 Answer

Set timing after replacing distributor


Ignition Timing
  1. sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Parking brake control should be applied.
    Depress the parking brake pedal, and warm the engine to the normal operating temperature.
  2. Turn off all electrical loads.
  3. Start the engine and rev it to 2000-3000 rpm two or three times and allow the engine to return to the idle.
  4. Check the idle speed. The idle speed should be between 700-800 rpm in PARK (P) or NEUTRAL (N) position.
  5. NOTE: Make sure that the timing pointer is pointing to the 15° Before Top Dead Center (BTDC) mark on the crankshaft pulley. Each notch on the crankshaft pulley represents 5 degrees.
    Check the ignition timing with a timing light.
  6. If the marks are not aligned, loosen the distributor bolt and turn the distributor to make the adjustment. The ignition timing should be between 13°-17° BTDC.

Feb 22, 2009 | 1999 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...