Question about 2000 Ford Focus

1 Answer

I have a 2003 BMw 760 LI it has a code P021 for crank position sensor, I replaced the sensor and cleared the light but it is still giving the same code

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,066 Answers

Code P012 is not a valid code. Please recheck. You need one more number in the code.

Posted on Mar 17, 2014

  • Harry Downs
    Harry Downs Mar 18, 2014

    sorry codes are P0021 and P0024 I replace the cam position sensor and cleared the light but it's still coding

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

06 bmw 525i codes p0174, p0171, p1338, p0340, p0365, and p1315


codes p 0171 and 174 refer ti system too lean
codes p 0338,340,365 refers to crank. and can shaft position sensors
code p1338 again is camshaft position sensor
code p1315 again is camshaft position sensor
too lean can be from fuel pump pressure too low
and position sensors can be wiring , connections sensors.
Involved in all these , one of the possible causes is the ECM
IF it is possible get a serviceable replacement ECM unit and substitute it first as there is no point in replacing all the rest if the ECM is faulty
could be water in the connections , corrosion etc
it is always suspect when so many different codes suddenly appear at the same time

Aug 22, 2016 | BMW Cars & Trucks

1 Answer

CAR WAS NOT STARTING ALL THE TIME-CODE PO337. REPLACED CPS, CLEARED CODES, CAR DOES NOT START AT ALL. HELP


code p 0337 refers to crankshaft position(CKP) sensor ---low input====causes ---wiring short to ground--CKP sensor ---ECM
did you replace the correct sensor as it is the crank shaft sensor and not the cam shaft position sensor which would be a code p 0340 on wards

Dec 01, 2015 | 2003 Saab 9-3 Linear

2 Answers

If both cam/crank position sensors have ONLY been unbolted and replaced with new sensors, do they require synchronization?


Sensors do not need to be recalibrated , the ecm should have the codes cleared . Then turn the ignition system on with data reader hooked up to see if sensors repaired the fault code.

Oct 11, 2015 | 2003 Ford Mustang

1 Answer

Subaru ecu


try the crank speed/position sensor as this controls the engine revs as well as other things

May 01, 2014 | 2003 Subaru Baja

1 Answer

2003 BMW 760 LI P021 code


cool do send photos of the Jeep BMW frankencar.. love them...

Mar 17, 2014 | 2006 Jeep Liberty

1 Answer

2003 bmw 760 li has P021 code I replaced the Cam position sensor but code still remain


Check for voltage and ground at the sensor plug. If you have it, then you have an internal problem.

Mar 17, 2014 | 2000 Ford Focus

1 Answer

P0340 signal camshaft sensor


The P0340 DTC just might be telling you to replace the camshaft position sensor.

Aug 12, 2017 | BMW 318i Cars & Trucks

1 Answer

How do get rid of the EML light


You can get it read for free by Autozone or Pepboys, depending on what code it gives you can decide if it is worth it to take it to a dealership and have the sensor replaced (which is the usual cause). Or they can clear the code and get rid of the annoying light for free.

Andrew

Aug 24, 2011 | 2003 BMW 325

2 Answers

Crankshaft Position Sensor Error P0335 recurred after r&r


In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Jul 25, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
2000 Ford Focus Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...