Question about 2000 Oldsmobile Intrigue

1 Answer

BCM LOCATION 2000 OLDS INTRIGUE

NEED TO LOCATE THE BODY CONTROL MODULE ON 2000 OLDS INTRIGUE-CAN YOU HELP?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 12,147 Answers

It is located under the dash left side above the parking brake ! There are four wiring connectors to it !

Posted on Mar 13, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 119 Answers

SOURCE: ECM location 1998 Oldsmobile Silhouette

On the 98 Silhouette, the PCM should be located in the air filter housing.

Posted on May 21, 2008

  • 50 Answers

SOURCE: crank position sensor location

you will need to remove the starter to gain acess to the ckp sensor. once you remove the starter look on the engine block and you will see the sensor. The only problem with doing this repair yourself is that you will not be able to preform the crankshaft position variation learn procedure with out a factory scan tool. The vehicle may crank an run, but the timing advance curves will be wrong so the vehicle will probably cut off every time you remove your foot from the gas pedal. Hope this info helps!

Posted on Aug 18, 2008

  • 8 Answers

SOURCE: I am seeking location of

Disconnect Car Battery
I replaced the ignition switch in my wifes 2000 intrigue. (ignition mounted in front dash). I had to take off the knee bump trim and the trim around the instrument housing and remove the instrument cluster. Leave it connected and just lay it on the dash. You also need to remove the radio to get to one of the screws that hold the ignition switch module. Once you get that loose you can pull it out so you can disconnect the wires going to it.
If you need to replace the ignition module insert the key and turn to accessories, there is a small metal button to push in, then your key and the lock part will fall out to install into your knew ignition module. At that time you can also remove the cruise control cable.
I am not a mechanic and the whole process only took me an hour or so.
I replaced my ignition module to fix the heater and AC operation. It also fixed the cruise control that hadn't worked for a year.

Posted on Jan 30, 2009

emissionwiz
  • 76630 Answers

SOURCE: where is the air bag

under the right front seat covered by carpet flaps

Posted on Apr 19, 2009

  • 1 Answer

SOURCE: Can anyone tell me where the fusebox is for the 2000 Oldsmobile Intrigue.

fastboyz is correct. There are two fuse panels. One in the engine area near the battery as he describes. The other one is on the passenger side at the end of the dash board. You have to open the passenger door. If you look at the dash board you will see a panel box cover built-in to the dash. The cover fits the contour shape of the dash. Pull on the cover and that will expose the fuses.

Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BCM in 2005 Saturn Vue


Remove the radio bezel. Refer to Radio Replacement .
Disconnect the body control module (BCM) electrical harnesses.
Remove the BCM from the instrument panel (I/P) retainer:
3.1. Pry the BCM tabs from the locking tabs on the underside of the restraint.
3.2. Slide the BCM out of the retainer

The BCM needs to be programmed if replaced !
The body control module (BCM) must be programmed with the proper RPO configurations. The BCM stores the information regarding the vehicle options and if the BCM is not properly configured with the correct RPO codes, the BCM will not control all of the features properly. Ensure that the following conditions exist in order to prepare for BCM programming:
• The battery is fully charged.
• The ignition switch is in the ON position.
• The data link connector (DLC) is accessible.
• All disconnected modules and devices are reconnected before programming.
The following procedures need to be performed to properly configure a BCM:
BCM Programming
Passlock Learn
Program Key Fobs

Body Control Module (BCM)
In the center of the I/P, behind the HVAC control module

Dec 06, 2016 | Saturn Cars & Trucks

2 Answers

What tools are needed to replace BCM?


Important: Perform new BCM setup when you replace Body Control Module (BCM). Refer to Body Control Module (BCM) Programming/RPO Configuration .
Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
Remove the left instrument panel insulator. Refer to Instrument Panel Insulator Replacement in Instrument Panel, Gauges and Console.
Disconnect the BCM electrical connectors.
Push the BCM up and move the bottom of the BCM away from and out of the mounting bracket slot in order to remove the BCM.
During Body Control Module (BCM) related service, the procedures below are designated to set-up the BCM correctly. Before you start, read these procedures carefully and completely.

Setup New Body Control Module (BCM)
Tools Required
Scan Tool (Tech 2) GM factory scan tool !
Important:
• Read this procedure carefully and completely.
• The BCM will not function properly if the Setup New BCM procedure is not performed.
• Perform the Theft Deterrent Re-learn procedure after successfully finishing the Setup New BCM procedure. If the Theft Deterrent Re-learn procedure is not performed after a BCM replacement, the following conditions may occur:
- The vehicle will not be protected against theft by the PASSLOCK system.
- The engine will not crank nor start. Your best bet is to take your vehicle to a dealer or a ASE certified repair shop who has proper tools .

Feb 16, 2016 | 2000 Oldsmobile Intrigue

1 Answer

Is the ac compressor controlled by the computer on a 87 olds toronado?


An '87 Olds Toronado has three computers: the ECM (engine control module), the BCM (body control module), and the IPC ( instrument panel cluster). The A/C compressor is controlled by the body control module.

May 02, 2014 | 1991 Oldsmobile Toronado

1 Answer

Interior Lights, Radio, and Gear Indicator Light on Cluster will not turn off when power is connected


The door actuator ,door ajar switch has nothing to do with the Gear Indicator Light on Cluster . Did you have the BCM programmed ? Can't just replace this without programming . Having the BCM check for DTC'S - diagnostic trouble codes should have been the first step in the diagnostic's for this problem an testing power an grounds . Is the door ajar light lit on the insturment cluster ? If not ,it's not a door actuator or door ajar switch .

Important: Perform new BCM setup when you replace Body Control Module (BCM). Refer to Body Control Module (BCM) Programming/RPO Configuration .
Fuse Block
Right side of the IP, in the right front door opening
RAP relay ,contacts stuck closed . Right I/P fuse box ! Open the passenger door ,at the end of insturment panel pull plastic cover !

Jul 20, 2017 | 2000 Oldsmobile Intrigue

1 Answer

Bcm location for 1998 s series blazer


I'm not positive a 1998 model has a BCM, the 2000 model is behind the dash near the ECM.

Sep 05, 2012 | 1998 Chevrolet Blazer

1 Answer

Bcm????going out???hesitation n stalling


The BCM is the body control module, which controls the various items for the body of the car, such as the dash and so on. The ECM is for the engine. May have a fuel delivery problem, check the fuel pressure. Also check the idle air control valve, and map sensor.

Mar 10, 2010 | 1999 Oldsmobile Intrigue

1 Answer

Security Start- 2000 Intrigue


it can be either the tumbler assembly for the key or the body control module. sometimes it times out and you can start it, sometimes not. happened to us with our impala. ended up being the BCM

Aug 01, 2009 | 2000 Oldsmobile Intrigue

1 Answer

1998 Intrigue: Security problem or ???


I'd say the BCM(body control module)

Jul 19, 2009 | 2000 Oldsmobile Intrigue

2 Answers

Dash Lights on


sounds like body control module

Jun 13, 2008 | 2000 Oldsmobile Intrigue

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...