Question about 2005 Kia Picanto 1.1

Open Question

Clutch hard to push down - 2005 Kia Picanto 1.1

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleed clutch hydraulic system John Deer 4300 Tractor - year 1998


two of you needed here ,put a big screwdriver into the operating arm and pull it back so the piston goes in ,slacken bleed nipple then helper pushes clutch down -hold it down then tighten nipple .repeat a few times and you will feel pressure on the clutch arm ,now get helper to push pedal down and hold it down ,pull bar to push piston in as it moves you open nipple then close it after a squirt of air comes out and repeat this a few times and it should have a hard pedal

Dec 06, 2014 | Cars & Trucks

1 Answer

I had a new clutch asembly and new slave cly put in my 1990 nissan truck about year and half ago. My problem is my clutch is hard to push down and if i don't push it all the way to floor it will g


replace the clutch master cylinder. The rubbers on the piston swell over time and/ or break down blocking up the ports in the cylinder.. Wrong fluid is the main culprit for this type of fault.

Mar 29, 2013 | Cars & Trucks

1 Answer

I just bought a 1997 BMW Z3 1.9 engine 5 speed, It is very hard to shift into all gears, if I push it all the way to the floor hard it gets easier but still sort of hard, is there a adjustment for the...


you have a bought a car with a worn out clutch end of story ,so take gearbox out and then take old clutch in hand to auto factor so you get the right clutch first time then fit it and you will have a nice car ,the clutch is hard to push down because the diaphramn spring in the pressure plate is working overtime because the clutch disk is worn to excess .not too difficult on this rear wheel drive car though just dirty work

Feb 26, 2011 | BMW Z3 Cars & Trucks

1 Answer

'05 Frontier w/ 6-speed manual transmission. Push the clutch straight in and truck will not start. Push the clutch in and hard to the left the truck will start just fine. No problems with starter,...


It's called the clutch switch and it's supposed to only allow current to the starter when the clutch pedal is depressed all the way down, releasing the clutch. It's bolted in front of the clutch pedal. Yours must be bad or shifted to the left somehow. Have it checked, then repositioned or replaced.

Nov 04, 2010 | 2005 Nissan Frontier

1 Answer

Clutch is hard to push in and has to be pushed way down to engage in 1999 nissan sentra. Can the clutch be loosened ?


Sorry, but your clutch is self-adjusting. The symptoms you describe indicate that it's time for a replacement.

Bill B

Aug 24, 2010 | 1999 Nissan Sentra

1 Answer

I just got a new used 1995 honda accord and already i'm really unhappy. The gears stick terribly and the breaks... you have to push down really hard and they don't break fast. What can i do about the gears...


the gears are sticking? is the shifter just really tight and hard to move from one gear to the next, or even just wiggle around in neutral? if so, you may need new bushings for it. which are not very expensive. IF the shifter wiggles around easily in neutral, but hangs in a gear when you press the clutch in all the way, you could need a clutch, OR hopefully you can just try bleeding the clutch line. at the master cylinder on the transmission. the breaks.... do you have to push the pedal down really hard, or really soft and far? if you're putting a lot of pressure on the pedal but you don't have to push the brake pedal all the way to the floor, that would indicate to me that your pads and rotors are glazed over. you should replace the rotors, pads and have the calipers checked, and have the brakes bled. if you've got to push the pedal all the way to the floor, there's a good chance all you'll need is to have the brakes bled.

Feb 07, 2010 | 1995 Honda Accord

1 Answer

How to bleed the clutch on a 1990 toyotai just put a clutch in the clutch paddle wornt'get hard to push the to change gears


Fill clutch master cylinder with fresh brake fluid.
Pump a few times and hold down.
Open bleeder at clutch slave cylinder then close.
Repeat this until clutch pedal feels normal and full movement is seen at clutch slave cylinder.


Sep 09, 2009 | 1990 Toyota Corolla

2 Answers

Clutch pedal is very heavy to push down


If the clutch in your car is hydralic there is no way to adjust that type of clutch. That you describe the clutch as being hard to push and that you have to have the clutch "right down on the floor to engage a gear" is an indication that the clutch is worn and needs to be replaced. If the clutch in your car is pushed by a cable, the cable might be adjustable and if that is the case you might get a few more months of use from the car, but the fix is still the same, you will need to get a new clutch put in your car.

Nov 26, 2008 | 2005 Hyundai Tucson

Not finding what you are looking for?
2005 Kia Picanto 1.1 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...