Question about Cars & Trucks

Open Question

Seat inca 1.9 SDI van,where is the tempture gauge sensor located.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: timing belt settings on seat inca van

If your caddy is the 1.9 diesel
The mark you are looking for is on the flywheel. Remove the plastic plug in top of the bell housing to reveal a small arrow. Rotate engine until the flywheel TDC mark lines up with this arrow
John

Posted on Feb 17, 2009

  • 123 Answers

SOURCE: I ask a question 2

The engine temp sensor is near the thermostat toward the front of the engine. Is the car actually running hot? I would measure the actual water temp and be sure before I started just replacing sensors.

Posted on May 07, 2011

TDISLine
  • 1874 Answers

SOURCE: seat inca van 00 sdi

Timing belt set-up for a 2000 Seat Inca 1.9 SDi

1. Align the crankshaft timing marks on the flywheel / gearbox

tdisline_583.jpg
2. Remove the valve cover
3. Lock the camshaft

tdisline_584.jpg
4. Fit the injection pump locking pin

tdisline_585.jpg

5. Loosen the camshaft gearwheel bolt, 180 degrees. Use a wrench to counter-hold
6. Loosen the camshaft gearwheel while holding it in place

tdisline_586.jpg

7. Fit the timing belt in the sequence as shown in the below figure: a - b - c - d - e - f - g

tdisline_587.jpg

8. Fit the timing belt and camshaft gearwheel together
9. Turn the tensioner clockwise to align both marks

tdisline_588.jpg

10. Tighten the large bolt on the tensioner to a torque of 20 Nm
11. Check for correct fit
12. Lock the camshaft. Tighten the camshaft gearwheel bolts: 45 Nm. Use a wrench to counter-hold
13. Remove helping tools
14. Turn the engine two rotations by hand
15. Repeat the procedure if required
16. Fit the vacuum pump
17. Refit the crankshaft pulley. Tighten torque: 20 Nm + 20 degrees
18. Fit the timing belt cover
19. Refit the valve cover
20. Fit the ancillary drive belt
21. Refit the inlet air manifold hoses
22. Check the injection timing

Torque settings:
Camshaft gearwheel: 45 Nm
Tensioner pulley: 20 Nm
Crankshaft pulley: 20 Nm + 20 degrees

Posted on May 26, 2011

  • 1 Answer

SOURCE: 2001 seat inca sdi van with starting problems. It

wene i reverse my seat inca van it makes a noise how do i fix this

Posted on Jun 07, 2011

dttech
  • 4803 Answers

SOURCE: seat inca van will start but wont take reves

Sorry, your question does not contain enough information for anyone to help you with your problem. For anyone to provide the information for you, they will first need to know the YEAR, MAKE, MODEL, and ENGINE SIZE of the vehicle that you want the information for.

Posted on May 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

01 Inca van 1.9 SDI keeps going into limp mode and won't accelerate no lights on dash what could problem be


Git a scan w factorygear at a private shop...not a dealr. Dont let them dujust a codereadr....seek out xperienc

Nov 14, 2015 | Cars & Trucks

1 Answer

Seat inca van will not start fuel problem


Need more info. Sometimes there is more than one fuel filter. Make sure the fuel pump is working. Make sure if it is fuel injected that there is enough fuel pressure.

Dec 31, 2014 | Seat Cars & Trucks

1 Answer

Seat inca van will notstart turning over o.k. Took stop solenoid out to check no fuel in pump


Change the fuel pump after you change out the fuel filter. The clog could have burned out the pump.

Dec 31, 2014 | Seat Cars & Trucks

1 Answer

Seat inca van will not start fuel problem


Things to consider:
1. Fuel pump bad
. a. Have someone turn the key to the on position while you kneal at the side rear and listen for the fuel pump to engage. If you hear the sound of a small motor (pump) running, its good. If not, replace it.
2. Fuel filter may be plugged, fuel injector(s) plugged.
3. If a mechanical fuel pump (older vehicles, mounted on engine block, replace.
Also check all fuses and relays to ensure ALL are in good shape. Replace as necessary.

Dec 31, 2014 | Seat Cars & Trucks

1 Answer

2004 seat inca van keeps losing power, any ideas


need more details, whats been done, how often dos it happens,usually noticed after what???

Aug 16, 2013 | Seat Cars & Trucks

1 Answer

Clutch pedal solid on siat inca 02 sdi van


It is a good thing to have a Solid Pedal or are you saying it is not able to disengage the Clutch?

Clutch Failure / Pressure Plate / Thrust Bearing Failure is the only thing that will not allow Disengagement.

Apr 08, 2013 | Cars & Trucks

1 Answer

Seat inca van 00 sdi 1.9 diesel.. tension polly came loose.. timing belt slipped.. I need to know how to reset it again. Where are the markings on the crank shaft and the cam shaft? Please attach any...


Timing belt set-up for a 2000 Seat Inca 1.9 SDi

1. Align the crankshaft timing marks on the flywheel / gearbox

tdisline_583.jpg
2. Remove the valve cover
3. Lock the camshaft

tdisline_584.jpg
4. Fit the injection pump locking pin

tdisline_585.jpg

5. Loosen the camshaft gearwheel bolt, 180 degrees. Use a wrench to counter-hold
6. Loosen the camshaft gearwheel while holding it in place

tdisline_586.jpg

7. Fit the timing belt in the sequence as shown in the below figure: a - b - c - d - e - f - g

tdisline_587.jpg

8. Fit the timing belt and camshaft gearwheel together
9. Turn the tensioner clockwise to align both marks

tdisline_588.jpg

10. Tighten the large bolt on the tensioner to a torque of 20 Nm
11. Check for correct fit
12. Lock the camshaft. Tighten the camshaft gearwheel bolts: 45 Nm. Use a wrench to counter-hold
13. Remove helping tools
14. Turn the engine two rotations by hand
15. Repeat the procedure if required
16. Fit the vacuum pump
17. Refit the crankshaft pulley. Tighten torque: 20 Nm + 20 degrees
18. Fit the timing belt cover
19. Refit the valve cover
20. Fit the ancillary drive belt
21. Refit the inlet air manifold hoses
22. Check the injection timing

Torque settings:
Camshaft gearwheel: 45 Nm
Tensioner pulley: 20 Nm
Crankshaft pulley: 20 Nm + 20 degrees

May 26, 2011 | Volkswagen Passat Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...