Question about Ford Cars & Trucks

1 Answer

Squealing noise when releasing clutch

Squealing noise when changing gear and releasing clutch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 485 Answers

You might have to change your release bearing. When you change this, you have to change the pressure plate, Clutch disk, the pilot bearing as well to assure you of a longer time without problems.

Posted on Mar 17, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75117 Answers

SOURCE: Gear Box

You need to check the adjustment on the shifter, I think that may be the problem, do that before assuming the gearbox is defective.

Posted on Sep 18, 2008

emissionwiz
  • 75117 Answers

SOURCE: 2001 BMW 330i clutch vibration

u have a worn out clutch pressure plate release bearing, that is what u feel and hear..

Posted on Dec 22, 2008

  • 114 Answers

SOURCE: Squealing noise

Hi there, you are right... the squeeling from what you explained is the throw out bearing or release bearing .

Posted on Dec 31, 2008

  • 4793 Answers

SOURCE: My clutch making a creaking noise...

it is the pedal box that is creaking NOT the clutch,quiet a common "fault",spray silicon around the pedals should cure it...

Posted on Jun 14, 2010

johnjnail
  • 1702 Answers

SOURCE: I changed my clutch and releasing bearing but the

a release bearing will make noise when you push on the clutch, the input shaft bearing will make noise when you release the clutch, the transmission will have to be removed and torn down to replace the bearing.

Posted on Apr 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch started squealing on my f350 then hard to engage in gear


The transmission will need to be removed. Probably will need a new clutch disc, pressure plate, release bearing and pilot bearing. The flywheel should be removed and taking to a machine shop to have them resurface it.

Sep 08, 2014 | Ford F-350 Cars & Trucks

1 Answer

Loud snapping noise heard when changing gears


From the way you've described it your gear stick linkages maybe on there way out. When changing gear does the car resist getting into gear?

If it's more of a crunching sound then I would try double de clutching, to do this you need to:
change gear as usual but instead of holding down the clutch throughout the gear change hold it down to take the vehicle into neutral then release the clutch then push the clutch down again and change into desired gear.
To change down it's basically the same principal but you push down the clutch to put the vehicle into neutral then push the throttle down just to pitch revs then release the throttle and push the clutch down to change into your desired gear, if it won't go in to gear easily then rather the throttle until it does.

You can go onto youtube and search for double de clutching and I'm sure some results will come up

hope this helps!

Apr 30, 2014 | 2004 Nissan Altima

3 Answers

The clutch was having a hard time going into gear.All of a sudden there was a high pitched squeal/scream coming from the transmission area.


that sounds like a throw out bearing failure-is there any adjustment at the slave cylinder-it may be holding the bearing against the clutch and causing the noise-this thread may help-http://www.jeepforum.com/forum/f9/how-change-bleed-clutch-slave-cylinder-511531/- cheers Denny

Dec 22, 2013 | 2000 Jeep Wrangler

1 Answer

Whinning noise from engine when changing gear went to pull off in 1st gear car stalled and now cannot engae gears is this just the clutch cable or something else


Hi, I think the noise you were getting while changing gear is most likely to be the clutch release
bearing ( as you press the clutch down the release bearing contacts the clutch pressure plate
fingers ).
The whinning noise is the bearing seizing up,
Unfortunately it looks like yours has damaged the fingers of the pressure plate so the clutch is not disengaging to allow you to select a gear.
A clutch kit will need to be fitted this contains clutch plate, pressure plate, release beaing
I hope this dos`nt turn out to be to expensive for you
John ( South Wales UK )

Jun 17, 2011 | Hyundai Genesis Coupe Cars & Trucks

1 Answer

I changed my clutch and releasing bearing but the noise is still there. When ever i release the clutch the noise starts like the release bearing problem and when i take off in first and second gear there...


a release bearing will make noise when you push on the clutch, the input shaft bearing will make noise when you release the clutch, the transmission will have to be removed and torn down to replace the bearing.

Apr 15, 2011 | 2004 Honda Civic

1 Answer

When clutch pushed in it makes high pitched squeel


Im a mechanic, i think you will find it will be the clutch release bearing on the clutch fork, when you push the clutch in it will push the fork which will push the clutch release bearing onto the clutch plate which rotating with the engine revs

Mar 23, 2009 | 2000 Jeep Wrangler

4 Answers

Transmission shifting proublem M5R1 1997 FORD RANGER


internal slave cylinders are known to leak , unfortunate it is behind clutch assembly , i would change both , clutch master and slave cylinder

Feb 27, 2009 | 1997 Ford Ranger SuperCab

1 Answer

2001 BMW 330i clutch vibration


u have a worn out clutch pressure plate release bearing, that is what u feel and hear..

Dec 22, 2008 | 2003 BMW 330

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...