Question about Cars & Trucks

1 Answer

My miele novotronic 230c tumbledryer will not start the finish light remains on

The finish light stays on when I turn it off and back on it still wont start .I have tried turning it off at the mains but still no joy

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,822 Answers

You are in the wrong section.

Posted on Mar 17, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 133 Answers

SOURCE: grand cherokee jeep wont start

Is your leads of good quality?My advise is to charge your battery.

Posted on Mar 03, 2010

SOURCE: when the light switch is

Under he center of the dash is a square black box called the lighting control module. The timer circuit inside it has failed and needs replaced. Easy job try the junk yard if they will sell you one, some will not.

Posted on Nov 19, 2010

  • 977 Answers

SOURCE: turn signal wont flash, hazzard lights and turn

it may be the flasher unit is faulty & needs to be replaced, you should find it under the dash on the drivers side it could be a square or round unit with a connector plug on it, when you remove the connector plug the unit has three pins on it........hope this helps.......cheers.

Posted on Sep 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine light on during ignition


Any car produce after 1996 can be scan with an OBDII reader.

Check the date code on the battery to rule out old battery.
All battery has a service life of 48 or more month.

Also check the belt tension. When the 2 arrow / dot meet the it is worn.

A worn tensioner will not create enough frication to the alternator pulley.

Jan 15, 2014 | 2010 Chevrolet Equinox 1LT

1 Answer

Gear shift stays in park and abs esp and asr lights on


1) try to use the self diagnose.
2) place ignition swtuch in the start position, the lights coming on
3) engine starts, the brake light sould turn off inmediately. the ABS ligth will illuminate for aprox 6 seconds.
4) test drive the vehicle at speed above 20mph for a few minutes. during the test the both test lights should remain off, if any one of the warninign light utron, take note of the condition.
5) stop the vechicle using the braking pressure.both light should remain offf during the stopping procedure.
60 place the gear selector in to PARK, and observe the warning lights, they should both be off.
God bless you

Jul 09, 2012 | Cars & Trucks

1 Answer

When the light switch is shut off , the parking lights stay on. when the battery cable is disconnected, something clicks and they go off. cable hooked back up and they remain off. when they are turned back...


Under he center of the dash is a square black box called the lighting control module. The timer circuit inside it has failed and needs replaced. Easy job try the junk yard if they will sell you one, some will not.

Nov 19, 2010 | 1984 Ford F 350

1 Answer

Have to delite the abs lamp after chengce abs sensor? accent 97mod


If the ABS wheel speed sensor was defective and you replaced it, the ABS light will automatically turn off once the vehicle is driven. If the ABS light stays on, you still have another problem in the system.
If the light remains on, have the codes read and reply back with the codes and we can start diagnosing.
Regards,

Aug 14, 2009 | 1997 Hyundai Accent

1 Answer

My radio and shift selector light stays on when I remove the key,


The ignition cylinder has a taper at the back that move the switch in whatever position. The key has to be turned back to off. It happened to me when I pulled the key out it was still half way on but then i just move it back in place. Its a sloppy cylinder from age.

Mar 13, 2009 | 2000 Chevrolet Malibu

1 Answer

Reset master cylinder with ABS system


Disconnect the battery negative with the ignition key on and the engine not ON, only instruments on dash and radio on, connect it back on after two or four minutes, do not panic if You see sparks coming when you connect Battery back is normal, *** it well turn key OFF and start the car back an see, if problem remains, with key on press accelerator pedal 10 times fast and check if problem remains, contact dealer

Jan 22, 2009 | 1994 Pontiac Grand Am

1 Answer

A B S brake light on


Disconnect negative terminal on the Battery, with Key on ignition ON engine not running and radio ON, after two minutes or more connect it back, do not panic if sparks come wile connecting it back, make sure is clean and ***, go to Your ignition key and turn it of, then start the car and see if problem remains, you have a bad sensor or a an ABS problem

Jan 22, 2009 | 2003 Chevrolet Express

4 Answers

With the ignition off, the rear tail lights won't turn off


hiya if the rear lights are remaining on ? with no ignition it will be the brake lights staying on this is easily remendied/ checked by trypulling the brake pedal up by hand and see if lights go off ? if so then you will need to adjust the b/light switch which is positioned adjacent to pedal and can be screwed inwards towards the pedal untill the plunger on switch is pushed into the switch which puts lights off ensure pedal is fully up then adjust switch reconnect the wire/plug and press pedal slightly to ensure b/lights operate ok and then go off with pedal released ? on hyundai the brakelights do not req ignition on to operate hence more likely problem is as above good luck

Oct 10, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...