Question about Cars & Trucks

1 Answer

Oil coming out of sleev were the glow plugs go into its a plastic sleeve any idea what this is called and how would I fix it Nissan hardbody 3 16vvtd

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,197 Answers

You need to replace the valve cover gasket.

Posted on Mar 17, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: nissan hardbody turbo leaking oil

Where is it leaking oil ? If the oil is coming form the input sheft. The seal is bad. You need to rebuilb it or buy a new trubo.

Posted on Mar 12, 2009

  • 54 Answers

SOURCE: spark plug boot

hi im wes
the sleeve is a heat shield it keeps the manifold from baking the boot if you leave it off it will still work for a while it will however fail much earlier than if you put it back on hope this helps
thanks wes ps please rate me

Posted on Mar 26, 2009

  • 6982 Answers

SOURCE: plastic sleeve on shift linkage cable is broken

You cannot take the sleeve off. It comes with a new cable. Shift cable is enough for any parts man to know what you need. Generally this item is a dealer part.

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: Need to replace boot sleeve on manual trans shifter

The frame that holds the "leather" in place just pops right out (come at it from one side; it'll sort of pivot around the other side -- I can't recall which is which, but trial and error works). Alternately, if you remove the six screws holding the entire center console in place, it can slide forward and rotate such that it'll clear the e-brake. Alternately alternately, if you curl your fingers underneath the boot frame on the side facing the rear of the car, you can pop the darker gray smooth plastic part of the center console entirely off while leaving the whole center console screwed in.

Posted on Jun 24, 2009

roniecon
  • 6826 Answers

SOURCE: how do i remove the spark plug wires from the

Twist and pull,the metal sleave will come off the plug boot.

Posted on Nov 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crankshaft seal keeps leaking how do I align da seal, any pics


There are thin sleeves to put on the crankshaft to enlarge the shaft to cover the worn out area on the crankshaft ,so the seal will keep the oil in , These are available at a good auto parts store I believe we called them speedy sleeves. Older fords had problems with axels leaking differential oil on to brake shoes. Very common problem with small block chev V8's to leak oil at front cover of the motor. Just slide the sleeve on, and install the seal

Apr 15, 2017 | Cars & Trucks

2 Answers

2004 Chevy blazer, 4.3L ; Fuel leak: Where the two aluminum fuel lines go into the intake, the little black plastic sleeves are missing. What are those sleeves called and where can I buy them? Please help.


There are no sleeves..On these there are 2 connectors. In the connectors there are O rings/seals. what hold the connectors to the fuel rail are clips. To date, I can replace the O rings(just match them up) The connectors and the clips, good luck... I had to replace the fuel lines, from the manufacturer to fix them. Some times from the auto store, but not much. Usually wrong parts.

Dec 13, 2014 | Cars & Trucks

1 Answer

Why the diesel pump nissan hardbody is not getting the power


DIESELS DO NOT START FOR ONLY 3 REASONS.. 1. not getting fuel. 2. Glow plugs not working.. 3 major engine damage
1. air in system.. like you ran out of fuel, Fuel filter clogged, lift pump not working, no fuel in tank, Bad fuel. .. 2. glow plugs..check the wire at the glow plug to see if it has power. If it does not check the relay and fuse. glow plugs usually do not all go bad at one time. 3. major engine damage.. you would normally notice this by the noise the engine makes or it would not turn over..

May 25, 2014 | 2000 Nissan Maxima

1 Answer

Cambelt timing marks 4jx1


sounds like the injector sleeve O rings have failed this was common.
if you put a clear plastic piece of hose on supply line for diesel fuel filter to head fitting at front and fuel is not black but normal diesel colour thats good.
then put clear hose on return line fitting at rear of cylinder head and fuel is now darker, engine oil is by passing injector sleeve top O rings and entering into fuel gallery in head.
rocker cover, injector rail, injectors need removing and injector sleeves need replacing as well as O rings and seats.
a special tool is needed to remove the injector sleeves out of the head. you will also need to drain the cooling system before removing the injector sleeves, so coolant is also needed.
dealers have special tool for injector sleeves

Mar 28, 2014 | 1998 Isuzu Trooper

2 Answers

I have a 2002 nissan xterra and heater hose broke off at firewall,the insert thats inside the hose going into the firewall broke off inside the firewall.Is it possible to repair without geting behind the...


Remove the firewall rubber grommet to the broken pipe in the firewall. Clean the remaining end of the broken pipe real good, apply a drop of oil on it, then push the heater hose back in and tighten the hose clamp back on. You will need a 12 point box end wrench and it will be slow due to limited access. It should work.

Mar 06, 2012 | Nissan Xterra Cars & Trucks

1 Answer

Where are spark plugs located for the vauxhall signum


You will have to remove the plastic head cover, you will have to remove the oil fill cap and screws/nuts holding the cover to the engine. Once you have that removed you will see wires going to coil packs that will have to be removed in order to get to the plugs. Disconnect the + and - battery terminals before starting. Also, when removing the coil packs be gentle as not to damage the sleeve or spring inside the sleeve which connects the coil to the plug.

Nov 12, 2011 | Cars & Trucks

1 Answer

Plastic sleeve on shift linkage cable is broken


You cannot take the sleeve off. It comes with a new cable. Shift cable is enough for any parts man to know what you need. Generally this item is a dealer part.

Mar 26, 2009 | 1996 Chevrolet C1500

2 Answers

How do you change glow plugs in 06 f350 powerstroke? where is /are speed sensors on 06 f350 superduty powerstroke


remove the inner wheel wells or cut it back to get some access its tight that way though i would just remove the two of them its 10& 11 mm on the top sidde just let everthing hang , it is either 5.5 mm or a 7 mm . the speed sensor is in the transfer case for the 4x4 or on theh rear on the trans for 2wd

Feb 18, 2009 | 1995 Ford F350

1 Answer

2004 Nissan Murano, back door can't open


I had a similar problem with a sienna and sometimes the cable ( inside the door) between the handle and the latch gets stuck in the sleeve. Kind of like the brake cable on a bike.
take the panel off by removing all the screws you can see on the panel and pull the panel off. There will be plastic pins holding it. Some of them may pop off and some will break off.
Drip oil down the sleeve so the cable slides freely. I used bike chain oil. Do not use WD40. This is **** and will not work for very long. Try the handles a few times before you put the panel back.

Oct 06, 2008 | 2003 Nissan Murano

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...