Question about 1995 Ford Mustang

1 Answer

What tools will i need to change the front and back brakes on a 95 mustang V6 would like to get the tools up before i jack up the car and take wheels off then have to put them back on to run to parts store

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

My 1995 mustang uses a 13 mm socket for the front calipers. I used a screwdriver to pry the pads back before removing the calipers, easier than using the C-clamp method.
As for the back brakes if you have the shoe type brakes you will need a brake shoe adjusting tool to loosen the adjusters.
Probably a good sized 2-4 pound hammer.
Slip joint plyers.
A 5/16 -3/8 wrench for the bleeder screws depending on the one you have. I didn't need to bleed mine as I was able to remove the shoes without disturbing the wheel cylinders.
If you need to bleed the brakes a good bleeding kit or 2 people that can work together pumping and bleeding the brakes .
hope this helps.
As always I would refer the a good shop manuals such as Motor, Haynes or Chiltons.

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove starter from 95 mustang


disconnect your negative battery cable first, and make sure you have at least a jack and two jack stands. Jack up the front of the car and crawl underneath the passenger side just aft of the front wheel. The starter is a round cylinder attached to the bottom rear of the engine. It is held on by a few wires and two bolts; just disconnect and remove those and it will drop right out. Be careful, the starter is not light.

Oct 01, 2011 | 1995 Ford Mustang

1 Answer

How do i replace front pads; 2006 mustang v-6


Jack up car and used jack stands, remove both caliper bolt's, you will need a c-clamp to compress caliper piston in, used one of the old brake pads in front of the piston then press piston in with c-clamp, install new pads and do the same at other side, before moving car pump brake peddle till it get's hard and your done,good luck.

May 28, 2010 | 2006 Ford Mustang

1 Answer

What tools are needed for this car


a ratchet set and also jacks and something to depress the caliber is all you need!

Feb 04, 2010 | 1998 Chevrolet Lumina

1 Answer

Mustang rear brakes


nice car i have one myself but the back brakes are a little bit tricky because you can not just push the brake calipers piston back into the bore. but here is how you can do it. you need a large plieres and you have to put the head of the pliers into the calipers piston then spread apart the handels so that the head of the pliers opens up against the inside walls of the piston. then all you have to do is Turn the piston back into its bore. See the rear caliper piston on the mustangs are just like a bolt. they are threaded into the bore and when your pads were they screw them selves out so when you redo your brakes you have to screw them back in just like a bolt. I hope this helps you out on this and if you have any more questions about this procedure just let me know and i would be more than happy to assist you in this.
please rate me if you would
thanks
Aaron

May 29, 2009 | 1995 Ford Mustang

4 Answers

98 ford mustang


If your having problems with the rear piston going in it because you need a special tool that allows you to turn while pushing.

Apr 06, 2009 | 1998 Ford Mustang

2 Answers

Mustang airbags


Very well could But, I would check the Wiring Harness Connection, They could have Changed Between Years. The Air Bag itself will fit Though.

Jan 15, 2009 | Ford Mustang Cars & Trucks

1 Answer

1997 Ford Mustang / V6 - 3.5 liter / automatic


I have a 1997 ford mustang v6. It starts up for like a split second then dies out. Just replaced the fuel filter.

Aug 15, 2008 | 1997 Ford Mustang Cobra

2 Answers

Rear disc brakes on 2000 Mustang


yneed a tool to spin the piston and push back at the same time

Jun 23, 2008 | 2000 Ford Mustang

Not finding what you are looking for?
1995 Ford Mustang Logo

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...