Question about 1987 Chevrolet S-10 Pickup

1 Answer

I am traing to replece the ignition cylinder but i am having problems to taked out

Posted by on

  • camarenaalbe Jun 15, 2009

    I replece the ignition cylinder but i steel kant starer

  • camarenaalbe Jun 15, 2009

    I am steel having problems to star

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 95 Answers

The ignition switch is on the lower part of your steering column. Not very easy to get to but you can lower the steering column to get a better look at it. there should be 2 switches down there that have bars running to them. one is the headlight brights switch, you should be able to click the brights and see what switch you need to replace. there are 2 screws that hold the brights switch in place. you need to remove that switch first, then there are 2 more for the ignition switch. After that you just turn the switch on the bar to get it to remove. hope this helps, its not a hard job to do just hard to get to. Good luck :)

Posted on Jun 14, 2009

  • tomas sidlauskas
    tomas sidlauskas Jun 15, 2009

    need detail description whats going on,then maybe i can help you

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tra-for air leak age


http://www.engine-light-help.com/kia-check-engine-light.html
P1123 Long Term Fuel Trim Adaptive Air System Low - Read Our Article On Oxygen Sensor Codes For Help With This Kia Check Engine Light Code

Mar 27, 2013 | 2000 Kia Sportage

1 Answer

92 CHEVY 6 CYLINDER P/U X-TRA CAB


DO NOT KNOW WHAT THE PROBLEM IS WITH YOUR 1992 CHEVY PICK-UP, I UNDERSTAND IT IS AN EXTENDED CAB, AND HAS A SIX CYLINDER, PROB. A 4.3 V-6 ENGINE, NOW I JUST NEED TO KNOW WHAT KIND OF PROBLEM YOU HAVE WITH THE TRUCK AND I WILL TRY TO HELP.

Nov 20, 2011 | Cars & Trucks

2 Answers

Ignition key won't release to the lock position


The ignition barrel is faulty and needs to be repleced.

Sep 15, 2011 | 2001 Buick Regal

1 Answer

I have no power stering or brakes i have replaced the booster ,master cylinder ,brake pads and caliper what is the deal


does it have filter looking thing between hose going to brake booster if does replece it . do you vacuum at booster .

Nov 01, 2010 | 1996 Chevrolet C/K 3500

1 Answer

2000chevy malibu keyless entry problem need help


1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 22, 2009 | 2000 Chevrolet Malibu

1 Answer

Don't know where the spark plugs are located


The spark plugs are located in the cylinder heads in around the exhaust manifolds.

Mar 25, 2009 | 2003 GMC Envoy

2 Answers

Car ill not start


you need the electrical part of the ignition switch this is a common problem on this model.

Mar 21, 2009 | 1994 Acura Legend

1 Answer

Ignition key cylinder


You have to have the ignition lock exposed, take the covers off above and below the lock body that holds the cylinder.
Insert the key fully into the keyway, and turn it to ACC. On the ignition lock body, press on the "stop pin", that pokes out of the lack body, above where the cylinder is housed. Press on the "stop-pin", and extract the cylinder. If the key can not be turn ed to ACC, the cylinder will not come out.
Thanks for choosing FixYa. Please let me know if this solves your problem.

Dec 16, 2008 | 1993 Toyota Tercel

2 Answers

Ignition problem


Here is a relevant answer for you from this site, hope it will helps:
http://www.fixya.com/support/t596370-ford_f_150_ignition_problem

Jun 22, 2008 | 1989 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...