Question about 2008 Pontiac G6 Sedan

1 Answer

Pontiac G6 2008 sedan 2.4 L - uninstall/reinstall bumper cover

I need to remove the front bumper cover in order to give it some repairs due to scratch/cracks. How can I remove it and reinstall it.
This is a Pontiac G6 2008, base model, sedan, 4 cylinder, 2.4L

I would also like to know where I can find the serial number in order to buy the proper paint for my repairs.

Posted by on

  • jfgauthier Jun 14, 2009

    Do you have any pictures or manual on this?



    I'm not sure what you mean by push in clips.



    I see 6 clips on the top, headlights screws (2 on each), clips on wheels and then 6 screws I think under it. Will anything else come off with the bumper? (ie other parts). How hard is it to put it back on?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 175 Answers

Hi..there are two push in clips on the top side,under the hood.
There are two small screws on both the left and right side just
to the outside of the headlights.you have to remove the headlights.
Then you have to get underneath and remove the wheel liner from
both sides.Then reach up under the bumper and there are two bolts
that hold the bumper.once you remove all that,it will just slide off.
try this out..
thank u..
kindly rate my response..

Posted on Jun 14, 2009

  • Hariharanath V Jun 14, 2009

    hi..reinstalling it is the reverse process.

    try it out..

    thank u..

    kindly rate my response..

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to Remove and replace the harmonic balancer on my 5.3...everyone talks about lowering the cradle but no instructions on how to do this


Jack the passenger side up on the cradle. Use a jack stand or blocks for safety, behind the cradle. Remove the tire. remove the dust shield. To lower the cradle there are two bolts to release, front and back. You might have to remove the cover under the bumper to get to the front one. remove those bolts and lower down the cradle. You might have to pry down on the cradle and use a block to hold it down to get the balancer out.

May 29, 2016 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Detailed instructions on front bumper removal. NOTE: From all the videos, it appears the CAB is different than the sedan. An example is the grill does NOT come up with the hood.


Remove wheels. Remove fender liners front. Remove three nuts per side from inside fender wells. Remove fog lamp grilles. Remove vertical bolt just inside grilles--pointing up. Remove two screws per side under hood near front of fender. Put milk crate under front bumper. Remove belly pan first. Slide bumper forward onto milk crate, disconnect headlight washer line at quick disconnect if so equipped. Disconnect fog light connectors. Remove bumper.

Oct 16, 2015 | 2003 Audi A4 Cabriolet

1 Answer

Where can I get front bumper cover clips for my 2005 Chrysler Sebring sedan?


Check your local wrecking yards. If you cant find them there then go to a dealer.

Sep 17, 2012 | 2005 Chrysler Sebring Sedan

1 Answer

How to replace front bumper cover



Instructions

Engage the emergency parking brake, to avoid causing the car to roll or move when removing the bumper.

Release the screws holding the wheel well liners in place with a screwdriver. This will expose the screws holding the bumper bolts. Release the bolts holding the bumper in place, using a wrench, and have a friend support it while it remains wired to the car.

Disconnect the wiring running to the bumper to separate the fog lights from the car. Pull out the light fixtures from the bumper cover.

Remove the grill in the bumper cover, taking out the screws holding it into the cover. This will allow you to separate the grill and the bumper cover.

Secure the grill and light fixtures into the new bumper cover, using the hardware you removed from the old cover.

Reconnect the necessary wiring. Support the bumper cover in front of your car or have your friend hold it in place again.

Secure the bumper cover using the retaining bolts you took out earlier. Tighten the bolts to hold the bumper cover securely against the car.

Replace the wheel well liners with the screws you took out.


Jul 07, 2012 | 2006 Chrysler Pacifica

1 Answer

How to r & r front bumper on a 2001 mercedes ml320


you have a painted numer cover over the bumper that must be removed, before you can access the bumper and remove it, remove all attaching hardware that attaches the bumper>reinstall and align front bumper install bumper cover and align, and paint as neccessary, I wouldtake it to a body shop and have it repaired if you have not done this repair before as you may find misalignment and seized hardware.

Mar 22, 2012 | Cars & Trucks

2 Answers

How do you remove the front bumper cover on a 98 honda accord sedan EX


Apply the parking brake and raise the vehicle and support it securely on jackstands.

Disconnect the negative battery cable, then the positive battery cable and wait two minutes before proceeding further (make sure you have the code if you have an anti-theft radio because you will need it after disconnecting the battery).

Working under the vehicle, detach the screws securing the lower edges of the bumper cover (use a small screwdriver to pop the center button up on the plastic fasteners, but do not try to remove the center buttons. They stay in the ferrules)

Remove the bolts, screws and plastic pins on each side retaining the bumper cover to the splash shields. Remove the bolt on each side where the bumper cover attaches to the fender.

Working at the top, detach the retaining bolts (2) securing the bumper cover to the hood latch support. Remove the cover.

When you put it back, make sure the tabs along the top edge of the bumper cover fit into the corresponding clips on the body before attaching the bolts and screws. An assistant is helpful.

Hope this helps you.

Jan 05, 2010 | 1998 Honda Accord

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

I need to remove the front bumper cover in order to give it some repairs due to scratch/cracks. How can I remove it and reinstall it.


taking off the bumper is pretty easy ... i've done it plenty of times at work ... the good thing is that it comes off pretty simple without having to take off the headlamps or anything ... ok ... i'm gonna try ... open the hood ... take out the clips that are holding it on the top ... there's 5 of them i think ... then it's connected to the fender too ... remove the clips that connect the bumper to the fender liner on the side ... you're gonna need something like a clip remover for that cuz those sit pretty deep and are pretty hard to get out ... pull out the fender liner as far as you can and you'll see a screw that connects the bumper to the fender on the very tip of it ... i'm pretty sure it's a 7mm screw ... unscrew that and it should lossen up ... do that on teh other side too ... ok ... now ... bottom ... there are 7mm palstic screws on the bottom that hold the dirt blocker thing ... there's like 10 of them ... take out the cips and unscrew them ... the bumper should come off ... you might have to see what else is holding it ... but it's pretty easy ... top, sides, bottom ... doesn't matter which order you go in ... i usually start from the bottom ... then sided then top ... so yeah ... i hope this helps ...

Jun 14, 2009 | 2008 Pontiac G6 Sedan

1 Answer

Can't get the front bumper cover to release from fenders


they should be push in pins they should come out with a little effort. don't worry if one breaks they are cheap and locally able to get.

Apr 13, 2009 | Pontiac Montana SV6 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...