Question about 1987 Ford F 250

1 Answer

On a 1987 f250 is there a sleeve behind the harmonic bal this is a california truck

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

on a 1987 f250 is there a sleeve behind the - 1.image hope that helps

Posted on Oct 27, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where are the timing marks on a 1987 dodge dakotakota

They are located on the harmonic balancer the other marks are located top side right behind the harmonic balancer on a plate that sticks of from the front of the block.

Apr 03, 2018 | Dodge Cars & Trucks

1 Answer

Flywheel problems

yes, I have a 1987 2.8 internal engine. The engine came out of a 1987 camor,witch had auto trany. We put the engine in a 1989 s10 behind a 5 speed trany. I'm getting a bad vibration at idle speed and different engine speeds? I was told that 1987 2.8 counter weight on the flywheel, that bal the cranck. Not sure what to do to solve this problem?Could someone help me figure this 1 OUT? thanks, PUZZLED!!!!

Jan 04, 2014 | Dodge Cars & Trucks

1 Answer


The crankshaft harmonic damper may be coming apart, have this checked first.

Apr 06, 2012 | 1987 Chevrolet Camaro

1 Answer

1995 grand am 3100v6 replaced modual,cam sensor behind harmonic bal,and plugs still no spark whatnext

your module that the coil pack bolt too was your problem in the begining

Jan 14, 2010 | 1997 Buick Skylark

1 Answer

What is tightening torque of harmonic bal. bolt 1990 Honda Accord

1990 Honda accord
L4 2156cc 2.2ltr engine
crankshaft pulley bolt
apply engine oil to threads (a few drops)
tighten to 159 ft lbs
please rate my answer as I am new

Aug 29, 2009 | 1990 Honda Accord

2 Answers

Where is the timing cover on my 1990 f250

it is behind the water pump it is about 18"long and 8'wide. and it stops at the top of the oil pan

Aug 07, 2009 | 1990 Ford F250

1 Answer

Cant find the ignition timing on the 1987 chevy suburban...where is it located?

Maybe I should explain a little more. The timing chain cover is behind the water pump. the harmonic balancer is behind the lower set of pulleys in the center of the engine. If you look on the balancer there will be a mark running across it. You may have to rotate it to find it. The tab on the timing chain cover will have a few marks on it. Like 0,2,4 you should be able to see the tab looking down from the drivers side or looking down behind the water pump.

Mar 25, 2009 | 1987 Chevrolet Suburban

1 Answer

1987 F250 warning bell

look inside the glovebox there should be a wire harness inside at the top of the glove box or behind the glovebox. i had the same problem. there will be a little black or gray box on the end of the wires

Feb 12, 2009 | 1987 Ford F 250

1 Answer

1998 dodge ram 1500 pick up (not 4wd)

easier on lift if not ramps on ground chalk wheel use stands once all belts are off remove center bolt on bottom crank pulley install crank pulley remover you may have to remove outer part of split pulley thread three puller bolts into bal there should be holes for this snug all three tight install adapter into center where main bolt came out thread tool against adapter as you tighten in the bal pulls out once out replace timing case seal at bottom of cover lightly apply grease or lithium on inside of seal put new bal alighn on keyway install reinstall tool slowly with air ratchet or impact gun reinstall slowly the grease on seal will stop seal from dry start up once bal all the way in install center bolt outer pulley if taken off belts etc

Aug 24, 2008 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides