Need to see were throttle body sensor is on the car

inside the throttle body , an it has two .
Throttle Body Assembly
The throttle assembly contains the following components:
• The throttle blade
• The throttle actuator motor
• The throttle position (TP) sensor 1 and 2
• The throttle actuator control (TAC) module
The throttle body functions similar to a conventional throttle body with the following exceptions:
• There is no longer an idle air control (IAC) motor and associated air passages.
• An electric motor opens and closes the throttle valve.
• The TAC module is located within the throttle body assembly.
• The throttle blade is spring loaded in both directions and the default position is slightly open.
• There are 2 individual TP sensors within the throttle body assembly.
The TP sensors are used to determine the throttle plate angle. The TP sensors provide the powertrain control module (PCM) with a signal voltage proportional to throttle plate movement. Both TP sensor signal voltages are low at closed throttle and increase as the throttle opens.


Your best bet , take it to a qualified repair shop .

I looked into your year and it does not look like a replacement throttle body actuator is available. In case you want to know. The "Throttle Body Sensor" and "Throttle Position Sensor" are all inside the throttle actuator. They can not be separated and replaced. For your year, the throttle body and actuator are sold as an assembly.

At the throttle pedal.

It is located in the throttle body assembly . Your vehicle has electronic throttle control .
Throttle Body Assembly
The throttle body assembly contains the following components:
?€¢
The throttle blade

?€¢
The throttle actuator motor

?€¢
The throttle position (TP) sensor 1 and 2

The throttle body functions are similar to a conventional throttle body with the following exceptions:
?€¢
An electric motor opens and closes the throttle valve.

?€¢
The throttle blade is spring loaded in both directions and the default position is slightly open.

?€¢
There are 2 individual TP sensors within the throttle body assembly.

Oh yea it has two TPS - throttle position sensors ! An you have to replace the whole assembly !

Your vehicle has electronic throttle control an the Throttle position sensor's are internal to the throttle body assembly ! Your vehicle has two throttle position sensors .
Throttle Body Assembly
The throttle assembly contains the following components:
?€¢ The throttle blade ?€¢ The throttle actuator motor ?€¢ The throttle position (TP) sensor 1 and 2 You have to replace the Throttle Body Assembly !
Disconnect the negative battery cable. Remove the inlet hose assembly from the throttle body. Disconnect the throttle body electrical connection. Disconnect the hose clamps from the plenum-to-runner connector using theJ 43914 .
Remove the intake plenum bolts. Remove the EGR passage bolt. Rotate the plenum up and remove the throttle body coolant hoses, EVAP hose, and vacuum line from the throttle body.
Remove the throttle body nuts. Remove the throttle body.

Buy a new-gasket, unbolt throttle-body,
spray carb cleaner inside of throttle body
let soak respray take a long Handel like
tooth brush an clean it once done spray rag
an push threw throttle body several times till
clean an reinstall. Don't get sensors wet at all
an unplugging sensors on some cars can
need car computer reprogramming so
do at your own risk

The throttle body needs cleaned its gumed up.Take throttle body off and spray and wipe the inside of the throttle body with a can of throttle body cleaner this should free it up.If that didn't help then you need a throttle position sensor.Reset the computer after any sensor is changed.

on the hyundai the tps rarely fails. so check the pedal sensor on pedal of car. there are 2 sensors on this car, one on side of carburator, and one at accelerater pedal check this one first. the throttle body does not need to be changed to fix the tps. but usually it is located on the throttle body. at the throttle plate.

Removal & Installation

1. Disconnect the negative battery cable.
   
2. Disconnect the Intake Air Temperature (IAT) sensor connector.
   
3. Disconnect the breather hose from the valve cover.
   
4. Remove the air intake tube.
   
5. Disconnect the throttle cables by opening the throttle and moving the cable through the release slot.
   
6. Disconnect the vacuum hoses from the throttle body.
   
7. Disconnect the Throttle Position (TP) sensor and the idle air control valve connectors.
   
8. Disconnect the coolant hoses from the throttle body.
   
9. Remove the throttle body and discard the gasket.
   
10. Remove the TP sensor.
    
11. Remove the Idle Air Control (IAC) valve.
    
12. Remove the throttle body retaining nuts.
    
13. Remove the throttle body.
    

To install:

1. Install the throttle body.
   
2. Connect the TP sensor connector and the IAC valve connector.
   
3. Connect the coolant hoses to the throttle body.
   
4. Connect the vacuum hoses to the throttle body.
   
5. Connect the throttle cable.
   
6. Install the air intake tube.
   
7. Connect the breather hose to the valve cover.
   
8. Connect the IAT sensor connector.
   
9. Connect the negative battery cable.
   
10. Fill the cooling system
    
11. 
12. i hope this helps tps is attatched to hrottle body on other side than throttle cable
    
13. plz dont forget to vote rep[ly if you need more help
    

map sensor located on firewall right side of vehicle..3 wire connector..small black sensor..with a vacuum hose leading to it..throttle position sensor on right side of throttle body unit..3 wire sensor..iac located on front of throttle body..4 wire sensor