2005 Nissan Quest automatic sliding door does not close

Fuse 12 for the brake switch, but it covers a lot of other things as well that would be very noticeable.

Automatic Speed Control Device (ASCD) Brake Switch, Data Link Connector, Combination Meter, Heated Seat Relay, Park Neutral Position Switch, Display Unit, Steering Angle Sensor, Display Control Unit, Navi Control Unit, Back Door Control Unit, Sliding Door Control Unit RH/LH, Sonar Control Unit, Daytime Running Lights, Hands Free Telephone

Nissan Quest (V42; 2004-2009) fuses and relays

Fuse Box Diagrams https://fuse-box.info > nissan > nissan-quest-v42-2004...

Here you will find fuse box diagrams of Nissan Quest 2004, 2005, 2006, 2007, 2008 and 2009, get information about the location of the fuse panels inside the car ...

Missing: 1994 ‎' Show results with: 1994

heres the schematic I hope it helps you

On the 05 Odyssey there's a problem with the rear latch assembly(about $140each) located in the rear of each sliding door. The problem is that the latch assembly was not seal proplery and water can get into the latch cause the sliding door to act funny. Maybe replace the latch assembly will help you.

I'm not sure about the noise, but the jerking motion might be because your the center roller (located in the rear middle of the sliding door) has worn out and need to be replace. This is a will known problem.

Your problem is very hard to answer because 05-10 odyssey has so many problem with sliding door.

rear latch:
-door not to latch close
-door not to work

front latch:
-door not to open

lock actuator:
-door not to open
-door will pop when opening

window motor:
-window not to work
-door will only open half way

center roller:
-jerking motion when opening
-door kick back close while opening
-door kick back open while closing

Door motor:
-door not to work
-cause door to jam

good luck

Try this... it fixed my problem whereby the 2005 Toyota Sienna passenger sliding door would sometimes open and sometimes not, yet I could hear the motor trying to open/close it. It cost me 20 minutes and 10 drops of oil, not $1200.

First, get the door open. It took me two weeks of constant trying, but it finally opened.

Next, remove the plastic covering of the inside door handle this way: locate the two screws on the forward edge of the sliding door near the child-safety switch: (the switch is a small lever near the door latch, on the forward edge of the door) loosen and remove the two phillips screws, one above the child-safety latch, and one below.

Remove the plastic cover to expose the gears for the door open/close mechanism.

There's a bunch of intricate plastic and metal parts in there, all coated with white grease. I used some 3-n-1 oil to lubricate everything in there thoroughly, In my case, there was one part that was a little void of grease, hence it "stuck" occasionally.

Test the system. If it's Okay, replace the plastic cover, and re-install the screws.

Now my Toyota Sienna 2005 door never fails to open or close.

hi dan. on the sliding door,if you look at the art of the door frame where it latches,you will see 3 or 4 screws that hold the latch in place. with wear these will either become loose,or even though feel tight,will allow te latch to shift positions. loosen the screws,adjust the latch forward or back until it latches. then remove the screws and apply loc-tite to the threads to keep this from happening again.

The lift gate motor needs to be replaced. Preferably at the dealer ship. Its a pain to replace and most shops will do shoddy work and destroy your interior when doing it.

More than likely the lift gate motor has failed.

first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.

Trim Panel —Sliding Door Removal

1. Remove the sliding door trim panel finish panel.

2. Remove the sliding door trim panel Latch Remote Control —Sliding Door Removal

1. Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .

1. Position the watershield aside.

1. If equipped, disconnect the sliding door power door lock actuator electrical connector.

1. NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
2. Disconnect the sliding door rear latch cable.
3. Remove the bolt.
4. Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
5. Disconnect the sliding door rear latch cable from the latch remote control.

1. Remove the 4 sliding door front latch bolts.

NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.

1. Remove the bolts.

1. Remove the sliding door latch remote control.

Handle —Exterior, Sliding Door Removal

1. Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .

1. Remove the sliding door exterior handle.
   1. Remove the nuts.
   1. Remove the sliding door exterior handle.

U will need to buy a can of spray white grease and clean and then lubricate all the tracks the door channels on as well as all the latches for the door, this will cure the issue in most cases, did allot of these while working at a Ford dealer.