Question about 1989 Ford Bronco II

Open Question

What should fuel pump look like before installing

Fuel pump not working

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 300 Answers

SOURCE: fuel pump works when it wants to. installed new

I had the same problem, and resulted in a bad computer. In yours, some oxidized contacts has to be cleaned up.

Posted on Oct 14, 2010

Ad
alicantecoli
  • 22265 Answers

SOURCE: Fuel pump quit working. Installed a new fuel pump

did you check for a feed to the pump?? first

Posted on Jan 03, 2011

Ironfist109
  • 3018 Answers

SOURCE: installed new fuel pump in a 1993 tempo, fuel

Check the connector to insure it is functioning properly and check the relay (small black box) that feeds the power to the fuel pump. The relay panel will be under the hood.

Posted on Mar 08, 2011

scottomatic9
  • 11 Answers

SOURCE: ford 2006 f150 fuel guage does not work

have you checked the cable in the dash or seen if a bad wire there also

Posted on Apr 17, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New fuel pump won't prime. No fuel from gas tank to engie. Lines are clear.


The pump works without priming anything. If the tank is vented, and you have fuel in the tank, and the pump is installed correctly, it should pump fuel out.
Are you sure the pump is getting power and ground ?

Jun 24, 2013 | Mazda Protege Cars & Trucks

1 Answer

How do you replace fuel pump in lincoln navigator 2001


Fuel Pump Module Removal & Installation To Remove:
WARNING
Highly flammable mixtures are always present in any fuel related component. Smoking or carrying lighted tobacco or an open flame of any type may ignite the flammable mixtures.
WARNING
Even when the engine is not running, fuel in the fuel system remains under high pressure. Fuel system pressure must be relieved before working on or disconnecting any of the fuel lines, fuel tubes, or fuel system components. Failure to do so may result in accidental spraying of fuel, personal injury, or a fire hazard.
  1. Remove Fuel Tank. Fuel Pump ford-05-00-3947.gif

  2. Remove fuel pump lock ring.
  3. Remove fuel pump.
  4. Remove and discard fuel pump O-ring.
To Install:
  1. Install new fuel pump O-ring.
  2. Install fuel pump.
  3. Install fuel pump lock ring. Tighten to 66 ft-lb (89 Nm).
  4. Install Fuel Tank.
prev.gif next.gif

Oct 29, 2010 | 2001 Lincoln Navigator

1 Answer

Where is the fuel pump located on a 92 Lexus SC300?


Fuel Pump REMOVAL AND INSTALLATION ES300 CAUTION
Fuel injection systems remain under pressure even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. With the ignition switch in the LOCK position, disconnect the negative battery terminal. If equipped with an air bag system, wait at least 90 seconds or longer before performing any other work.
  3. Remove the rear seat cushion.
  4. Disconnect the fuel pump connector. CAUTION
    The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the fuel pump. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  5. Remove the floor service hole cover. NOTE: Do not lift the fuel pump assembly up using the wire harness.
  6. Remove the fuel filler cap. Disconnect the fuel outlet pipe and the return hose from the pump bracket.
  7. Remove the 8 screws and lift out the pump/bracket assembly with gasket.
  8. Remove the fuel pump lead wire.
  9. Pull the lower end of the pump off of the bracket.
  10. Disconnect the fuel hose from the pump and remove the pump.
  11. Remove the rubber cushion from the pump. To install:
  12. Install the filter and rubber cushion on the new pump and install the pump on the bracket.
  13. Connect the fuel hose and the wire connector on the pump.
  14. Using a new gasket, install the pump and tighten the eight screws to 35 inch lbs. (4 Nm).
  15. Connect the fuel pipe and return hose to the pump and tighten the bolts to 22 ft. lbs. (29 Nm).
  16. Connect the wire, install the service cover and replace the rear seat.
  17. Connect the negative battery cable.
  18. Start the engine and check for leaks. Fig. 1: Fuel pump assembly - ES300 294126.gif
GS300, LS400, SC300 and SC400
  1. Disconnect the negative battery cable. Wait at least 90 seconds before performing any other work.
  2. Remove the trunk floor mat.
  3. Remove the trunk trim cover.
  4. Disconnect the fuel pump electrical connector.
  5. Remove the rear seat bottom and seat back.
  6. Remove the partition cover.
  7. Remove the mounting bolts and remove the fuel pump set plate.
  8. Remove the three nuts and disconnect the fuel pump bracket from the tank.
  9. Disconnect the fuel hose from the bracket. Remove the pump, bracket and set plate as an assembly. To install:
  10. Install a new gasket on the set plate. Connect the fuel hose to the pump and bracket,
  11. Install the pump and bracket assembly with the three nuts; tighten the nuts to 48 inch lbs. (5 Nm). Install the set plate and tighten the bolts to 26 inch lbs. (3 Nm).
  12. Install the panel partition
  13. Install the rear seat cushion and back.
  14. Connect the fuel pump electrical connector.
  15. Install the trim panel.
  16. Install the spare tire and the trunk floor mat.
  17. Connect the negative battery cable.
  18. Start the engine; check the fuel system for leaks
  19. Road test the vehicle for proper operation.

Oct 13, 2010 | 1992 Lexus Sc 300

1 Answer

Does my 2000 ford expidition have a little compartment to replace my fuel pump.


Fuel Pump Module-in tank, no compartment to replace fuel pump Removal & Installation To Remove:
WARNING
Highly flammable mixtures are always present in any fuel related component. Smoking or carrying lighted tobacco or an open flame of any type may ignite the flammable mixtures.
WARNING
Even when the engine is not running, fuel in the fuel system remains under high pressure. Fuel system pressure must be relieved before working on or disconnecting any of the fuel lines, fuel tubes, or fuel system components. Failure to do so may result in accidental spraying of fuel, personal injury, or a fire hazard.
  1. Remove Fuel Tank. Fuel Pump ford-05-00-3947.gif

  2. Remove fuel pump lock ring.
  3. Remove fuel pump.
  4. Remove and discard fuel pump O-ring.
To Install:
  1. Install new fuel pump O-ring.
  2. Install fuel pump.
  3. Install fuel pump lock ring. Tighten to 66 ft-lb (89 Nm).
  4. Install Fuel Tank.
prev.gif next.gif

Oct 12, 2010 | 2000 Ford Expedition

3 Answers

Needs fuel pump


Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Sep 18, 2010 | 1997 Chevrolet Blazer

1 Answer

How can i replace the fuel pump for 1995 lumina


prev.gif next.gif REMOVAL & INSTALLATION Fig. 1: Exploded view of the fuel sender, including the fuel pump 88005g58.gif
  1. Properly relieve the fuel system pressure, as outlined earlier. CAUTION
    Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  2. If not already done, disconnect the negative battery cable.
  3. Raise and safely support the vehicle with jackstands.
  4. Safely drain and remove the fuel tank assembly as outlined later in this section.
  5. Detach the quick-connects from the fuel sender assembly and remove the fuel lines.
  6. Using tool J 35731, or an equivalent spanner wrench, remove the fuel sender lockring.
  7. Lift the sender assembly carefully out of the fuel tank.
  8. Remove the sender O-ring from the top of the sender and discard. WARNING
    Do NOT run the fuel pump unless it is submerged in fuel. Running the pump dry will cause serious damage to the fuel pump and may cause the pump to explode due to the oxygen in the air.
  9. Note the position of the fuel pump strainer on the fuel pump and, while supporting the pump assembly in one hand, twist the strainer off the pump and discard the strainer.
  10. Detach the fuel pump electrical connector.
  11. Remove the clamp from the fuel line at the top of the pump.
  12. Hold the fuel sender upside down on a work bench and pull the fuel pump out of the lower mounting bracket. Once the pump is clear of the lower mounting bracket, tilt the pump outward and disconnect the pump from the sender assembly. To install:
  13. Replace any attaching hoses or rubber sound insulators that show signs of deterioration.
  14. Install the rubber bumper and insulator on the fuel pump.
  15. Hold the fuel sender upside down and install the fuel pump between the fuel pulse dampener and mounting bracket.
  16. Attach the fuel pump electrical connector.
  17. Install the retaining clamp on the fuel line.
  18. Install a new fuel pump strainer on the outer edge of the ferrule until fully seated. The strainer must be facing the same direction as it was before removal.
  19. Position a new O-ring on the top of the fuel tank and install the sender assembly.
  20. Install the lockring using J-35731, or an equivalent spanner wrench.
  21. Install the fuel tank as outlined later in this section.
  22. Refill the gas tank.
  23. Connect the negative battery cable.
  24. Turn the ignition switch to the ON position to pressurize the fuel system and check for leaks.

Sep 18, 2010 | 1995 Chevrolet Lumina

2 Answers

How do i change a 2004 Lincoln LS fuel pump?


Hi. here's how to change the fuel pump. The actual electric fuel pump is in the tank on the right side. The tank is directly below the rear seat. If you remove the seat bottom you will find a 6 inch or so cover. Under the cover there is a plastic, threaded collar that locks the fuel pump into the tank. The driver's side also has a pump, but it works only my venturi effect from the electric pump on the other side. This pump is used to equalize the fuel level from left to right. The drive shaft tunnel prevents all but the very top of the tank from communicating left to right.

Aug 12, 2010 | 2004 Lincoln LS

2 Answers

How do i replace fuel pump on 1998 escort se 2.0


Removal & Installation WARNING Extreme caution should be taken when removing the fuel tank from the vehicle! Ensure that all removal procedures are conducted in a well ventilated area! Have a sufficient amount of absorbent material in the vicinity of the work area to quickly contain any fuel spillage. NEVER store waste fuel in an open container, as it presents a serious fire hazard!

This procedure will require a new fuel pump gasket for pump installation, so be sure to have one before starting.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat cushion and unplug the electrical connectors from the fuel pump.
  4. Unfasten the four pump access cover screws and remove the cover.
  5. If equipped, unplug the pump electrical connector located under the cover.
  6. Unfasten the fuel line clip(s) and disconnect the line(s) from the pump.
  7. Use a fuel pump locking ring removal tool or a brass drift and a hammer to unfasten the pump locking retaining ring.
  8. Remove the fuel pump and the gasket from the tank.


ac8ef02.gif

To install:
  1. Install a new gasket and place the pump into position in the tank.
  2. Install the pump locking retaining ring.
  3. Connect the fuel line(s) to the pump and install the line retaining clip(s).
  4. If equipped, attach the fuel pump electrical connection(s).
  5. Install access cover, then tighten the retainers.
  6. Attach the pump electrical connector(s).
  7. Install the rear seat cushion.
  8. Connect the negative battery cable.
  9. Start the car and check for proper operation.

May 13, 2010 | 1998 Ford Escort

1 Answer

How do I replace a 93" oldsmobile cutlass fuel pump dose anyone know where i could get a free guide with pics is pos.


Removal & Installation

57b1976.gif
Exploded view of the fuel sender, including the fuel pump


Click to Enlarge
  1. Properly relieve the fuel system pressure

  1. If not already done, disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Safely drain and remove the fuel tank assembly as outlined later in this section.
  4. Detach the quick-connects from the fuel sender assembly and remove the fuel lines.
  5. Using tool J 35731, or an equivalent spanner wrench, remove the fuel sender lockring.
  6. Lift the sender assembly carefully out of the fuel tank.
  7. Remove the sender O-ring from the top of the sender and discard.

WARNING Do NOT run the fuel pump unless it is submerged in fuel. Running the pump dry will cause serious damage to the fuel pump and may cause the pump to explode due to the oxygen in the air.


  1. Note the position of the fuel pump strainer on the fuel pump and, while supporting the pump assembly in one hand, twist the strainer off the pump and discard the strainer.
  2. Detach the fuel pump electrical connector.
  3. Remove the clamp from the fuel line at the top of the pump.
  4. Hold the fuel sender upside down on a work bench and pull the fuel pump out of the lower mounting bracket. Once the pump is clear of the lower mounting bracket, tilt the pump outward and disconnect the pump from the sender assembly.
To install:
  1. Replace any attaching hoses or rubber sound insulators that show signs of deterioration.
  2. Install the rubber bumper and insulator on the fuel pump.
  3. Hold the fuel sender upside down and install the fuel pump between the fuel pulse dampener and mounting bracket.
  4. Attach the fuel pump electrical connector.
  5. Install the retaining clamp on the fuel line.
  6. Install a new fuel pump strainer on the outer edge of the ferrule until fully seated. The strainer must be facing the same direction as it was before removal.
  7. Position a new O-ring on the top of the fuel tank and install the sender assembly.
  8. Install the lockring using J-35731, or an equivalent spanner wrench.
  9. Install the fuel tank as outlined later in this section.
  10. Refill the gas tank.
  11. Connect the negative battery cable.
  12. Turn the ignition switch to the ON position to pressurize the fuel system and check for leaks.

Oct 11, 2009 | 1992 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...