Question about 2009 Dodge Nitro 3.7

Open Question

2009 dodge nitro lugs down and shakes with engine light flashing when going up incline what is problem

Lugs down and engine light starts blinking going up incline

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 439 Answers

SOURCE: 2006 Dodge Caravan Engine Light Blinks 10 Times & wont start

It sounds like your starter needs cleaned or replaced. The poping noise could be the actuator not engaging right. As for the engine light, it could be just a coincidence.

Posted on Jun 23, 2009

  • 105 Answers

SOURCE: 2005 Dodge Caravan will not start and engine light flashing 10x

most likely it is the electronic control module which is the brain computer that runs the car and all of the functions and it is not allowing the electrical system to operate or come online. your power supply is not reaching the ignition due to some sort of either an electrical short or blockage.

Posted on Jul 26, 2009

  • 31 Answers

SOURCE: check engine light on diagnostics say rpm's too

That would be your rev limiter or your map sensor.

Posted on Sep 04, 2009

  • 125 Answers

SOURCE: I have a 2009 Dodge Nitro 4X4. How do I remove the oil filter

First, I have to say that being retired profesionnally of the mecanic I have not change it by myself. However, it seems that the 4.0 L is relatively easy to replace but the 3.7 L one is located near/between front axle/differential, the harmonic balancer and masked by a bunch of hoses.
Several users reported that the factory one is hard to remove being too much tighted in place.
These things being said, depending on your mecanic experience I'm sure it 'feasible' taking maybe 45 minutes rather then 2 minutes.
My only warning will be to resist to the idea to 'break it ' with a scewdriver with the idea to pry it if it's tight in place. It's really amateur and you could really be in trouble if it doesn't work. A strap wrench is very ofter the most appropriate tool.
Assuming positively you will reach this point, make sure the previous oil filet gasket didn't stay in place and second, put some oil onto the new filter rubber gasket to make the next removal easyer. Tight strongly by hands.
Hope it will help
Sorry for my english
Dan

Posted on Dec 27, 2009

  • 1 Answer

SOURCE: 2008 dodge nitro change oil light how to turn off ...

Directions are in the book, but you would put the key in and turn it all the way, just don't start engine. Pump gas pedal all the way to the floor 3 times slowly, but it has to be with 10 seconds. Turn key off and when you start again, oil changed chime and warning should not be on. If it is, try again.

Posted on Jul 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where the thermostat is located on 2009 Dodge Nitro 4.0 lt


If you follow the top hose from the radiator to the top of the engine block there should be a housing at the end of it. The thermostat should be under theat housing. By housing I mean a hard plastic or metal part that bolts the hose to the block

Jun 14, 2015 | 2009 Dodge Nitro

1 Answer

Check engine light on 2011 dodge nitro


Hey guys I have a 2011 Dodge Nitro 3.7 and today my engine light came on and it was running like I was on rumble strips. I floored it and it sputtered and ran terrible then the light started flashing then I cut it off tried to reset still the light came on. I put the scanner on it and it turned out to be the coil plug on the #3 cylinder. COIL PLUG. Hope this helps out GOD BLESS!

Sep 04, 2013 | 2011 Dodge Nitro

2 Answers

My 2000 Dodge Neon had the Check Engine light go on last night. And it was still on this morning. When I started driving it, it would shake when I came to a stop. I also noticed that the longer I drove it...


CODE PO202 FUEL INJECTOR 2 CONTROL CIRCUIT MALFUNCTION CONDITIONS.POSSIBLE CAUSES INJECTOR 2 CONTROL CIRCUIT IS OPEN OR GROUNDED BETWEEN THE INJECTOR AND THE PCM.OR INJECTOR 2 HAS FAILED ALSO PCM HAVE FAILED.ONLY WAY TO TELL IF PCM FIRING INJECTOR 2 IS DISCONNECT 2 INJECTOR ELECTRICAL CONNECTOR HOOK NOID LIGHT TO INJECTOR 2 CONNECTOR CRANK ENGINE.THE NOID LIGHT SHOULD BE BLINKING.IF NOID LIGHT STEADY YOU HAVE FAULTY PCM.IF NOID LIGHT NOT WORKING YOU HAVE BAD GROUND OR OPEN WIRE ON INJECTOR 2 ELECTRICAL CONNECTOR.

Feb 11, 2011 | 2000 Dodge Neon

3 Answers

My 2009 dodge nitro engine light came on - this is the first problem ive had with this vehicle- should i be worried and take it into the dealer?


this could be because a sensor is loose or the gas cap is not tight enough. it is a new feature on some cars. you have to turn 3 times after it starts tio click.

Jan 05, 2011 | 2009 Dodge Nitro

2 Answers

Is thr a switch that lets the nito know that u had changed the oil


If you have the R/T with the onboard computer, you can reset the light through that. If not, there is a very simple reset sequence. 

Begin with the vehicle off. 
Turn the key to the ON position, but do not start the engine.
Press the accelerator pedal to the floor and release it three times.
Turn the key to the OFF position. 

Now if you turn the key on or start the engine, you should see that the light has reset itself, and will only come back on after 3000 miles, or if the ECU senses an oil problem. 

Aug 22, 2010 | 2009 Dodge Nitro

1 Answer

2008 dodge nitro change oil light how to turn off had oil changed did not go out


Directions are in the book, but you would put the key in and turn it all the way, just don't start engine. Pump gas pedal all the way to the floor 3 times slowly, but it has to be with 10 seconds. Turn key off and when you start again, oil changed chime and warning should not be on. If it is, try again.

May 21, 2010 | 2008 Dodge Nitro

1 Answer

Keeps going on. What could be the problem?


It could be one of literally thousands of codes. Many auto part stores will scan your code for free. Be sure to write it down.

Mar 05, 2010 | 2008 Dodge Nitro

1 Answer

I'm going to install lighted running boards on my dodge nitro 2009,I need to know if there is any problum tying them into the interior lighting.


I would recommend splicing into the running light circuit. If you cant find the wire bundle in the chassis, I would run a wire back to the brake light box and tie into the running light system.

Nov 22, 2009 | 2009 Dodge Nitro

Not finding what you are looking for?
2009 Dodge Nitro 3.7 Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...