Question about Cars & Trucks

Open Question

2010 Ridgeline spark plugs

Undo the two fasteners on the cover, and it appears to still be attached in the center underneath. How do I get that off? Also, it looks like the fan is too close to allow the plug wire packs to come out... do I have to remove the fan? How do I get the fan out? Looks like it will be very difficult to get the bottom two screws out... and the wiring is attached with some kind of zip-tie fastener.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: SPARK PLUG WIRING

i am looking for a diagram for 1996 ford f-150 for the spark plugs.

Posted on Aug 30, 2008

tripletauto
  • 1450 Answers

SOURCE: 02' silverado,removing spark plugs

THE metal cover is just a sleeve on wire. it will come off with it. try turning wire back and forth to loosen it up from plug. helps a lot to have a set of wire puller pliers

Posted on Feb 03, 2009

  • 259 Answers

SOURCE: need to change the spark plugs and cannot figure out how to remov

you just pull them off the plugs hope this helps regards Jim

Posted on Mar 29, 2009

  • 462 Answers

SOURCE: need a diagram of the firing order of spark plug wires from coil packs to spark plugs

FROM LEFT TO RIGHT, 5/2 3/6 4/1. ASSUMING YOU HAVE THE 3.1L ENGINE.

Posted on May 31, 2009

alicantecoli
  • 22095 Answers

SOURCE: Remove spark plug wires from a 2005 silverado 5.3 engine

just check it first and see how its fitted ,its only a shroud

Posted on Jun 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you Remove head unit 1990 holden barina


First drain water . remove cables from plugs and any thing attached to the head. Remove valve cover, remove valve rocker. remove manifold. undo head studs , undo from the center working one stud at a time from left to right of center. lift off head.

Aug 16, 2014 | Cars & Trucks

1 Answer

Changing out spark plugs in 2010 toyota camry 4 cylinder


Down into the center of the valve cover, where the 4 wires are leading into.

Aug 10, 2014 | 2010 Toyota Camry LE

1 Answer

Replace spark plugs on 2005 cad develle


emove the cover in the center of the valve covers. There may be an electrical connector on both of those covers. If there is unplug the connector and remove the cover. The spark plugs will be underneath.

If there is no connector than you have coil over ignition. You will see 8 coils total. Each coil is held in with a single bolt. Remove the bolt, unplug the coil, remove the coil, and the plugs will be underneath.

Feb 03, 2012 | 2005 Cadillac Deville

1 Answer

Replace sparks on 2005 cad develle


remove the cover in the center of the valve covers. There may be an electrical connector on both of those covers. If there is unplug the connector and remove the cover. The spark plugs will be underneath.

If there is no connector than you have coil over ignition. You will see 8 coils total. Each coil is held in with a single bolt. Remove the bolt, unplug the coil, remove the coil, and the plugs will be underneath.

Feb 03, 2012 | 2005 Cadillac Deville

1 Answer

How to change spark plugs on 2005 cad deville


emove the cover in the center of the valve covers. There may be an electrical connector on both of those covers. If there is unplug the connector and remove the cover. The spark plugs will be underneath.

If there is no connector than you have coil over ignition. You will see 8 coils total. Each coil is held in with a single bolt. Remove the bolt, unplug the coil, remove the coil, and the plugs will be underneath.

Feb 03, 2012 | Cadillac DeVille Cars & Trucks

1 Answer

Location of the spark plugs for 2006 honda Ridgeline


There should be a plastic cover over the top of the engine. Remove that cover. You will then see the three coils on the front of the engine. Use a metric Allen or a 10mm socket to remove the bolts that hold the coils to the valve cover. Unplug the coils and then remove them. The plugs will be underneath. The rear three plugs are set up the Same way. They are a little more difficult to do but not impossible. If you have any questions let me know. Thank you for using fixya.com!

Oct 18, 2011 | 2006 Honda Ridgeline

1 Answer

I would like to know how to locate the spark plugs on my celica GT.


They are between the cams. On top of the engine there are 4 wire bundles in the center of the valve/cam cover connecting to the spark coils. Undo the connectors and remove the single bolt for each one. Lift up the spark coil assemblies and find the spark plugs in the bottom of the hole underneath good luck.

Feb 19, 2011 | 2000 Toyota Celica

1 Answer

How to remove the rear seat of a Honda Ridgeline 2010.


1. Pull the plastic panels under the seat bottom straight forward to remove them.

2. Remove the six bolts (14mm) holding the seat and center seatbelt in place.

3. Pop the two small plastic covers at the top and behind the seat using a trim removal tool or screwdriver tip covered in masking tape.

4. Lift the seat straight upward.

5. Remove.

The Service Manual states a 35 ft lb torque and must be re-installed in a certain sequence for the 6 seat anchor bolts (not the seat belt bolts). When putting the rear seat back in install the bolts in this order. (1) center left (2) center right (3) left lower (4) right lower (5) left upper (6) right upper.

Nov 09, 2010 | 2008 Honda Ridgeline

1 Answer

How do I replace the valve cover gaskets for a 1996 Ford Ranger w/ 3.0L Engine?


The valve covers installed on the 3.0L engine incorporate integral (built in) gaskets which should last the life of the vehicle. Replacement gaskets are available if required.
  1. Disconnect the negative battery cable. Disconnect the ignition wires from the spark plugs, but leave them attached to their wire looms.
  2. Remove the ignition wire separators from the rocker arm cover attaching bolt studs with the wires attached, then lay the wires out of the way.
  3. If the left hand cover is being removed, remove the throttle body assembly, the PCV valve and fuel injector harness stand-offs. If the right hand cover is being removed, remove the engine harness connectors, fuel injector harness stand-offs and air cleaner closure hose from the oil fill adapter.
  4. Using caution, slide a sharp thin blade knife between the cylinder head gasket surface and the valve cover gasket at the four RTV junctions. CUT ONLY THE RTV SEALER AND AVOID CUTTING THE INTEGRAL GASKET.
  5. Remove the integral gasket from the valve cover gasket channel. Note bolt/stud fasteners locations before removing gasket for correct installation. Clean gasket channel and remove any traces of RTV sealant.

To install:
  1. Align fastener holes, lay new gasket onto channel and install by hand. Install gasket to each fastener, seat fastener against cover and at the same time roll gasket around fastener collar. If installed correctly all fasteners will be secured by gasket and not fall out.
  2. Install valve cover to the engine, lightly oil all bolts and stud threads. Apply a bead of RTV sealant at the cylinder head to intake manifold rail step (two places per rail).
  3. Place the valve cover on the cylinder head and install attaching bolts and studs. Tighten the attaching bolts to specifications.



0996b43f802117db.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Rocker arm cover installation on 3.0L engines
  1. Install all remaining components in reverse order of removal procedure. Connect the ignition wires to the spark plugs and reconnect the negative battery cable. Start the engine and run to normal operating temperature, then check for oil and vacuum leaks.

Jan 19, 2010 | 1996 Ford Ranger SuperCab

1 Answer

WHERE ARE THE SPARK PLUGS ON A 1999 ELANTRA


There is a plastic cover over the middle part of the top of the engine. You should see the spark plug wires going under the cover from the ignition pack on the driver side of the engine. Undo the bolts holding the cover down. The spark plugs are underneath.

Oct 24, 2009 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...