Question about 1984 Chevrolet Chevy

Open Question

Ignition switch test for 1984 chevy truck

Need to know if you can test the ignition switch in a 1984 half ton chevy truck

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 275 Answers

SOURCE: 1989 Chevy Pick up Ignition switch broken

use a test light the wire from the battery should be hot all the time the wire that goes to the solenoid should be hot when the key is turned over to start and the wire going to the coil should be hot when the key is in run.

Posted on Nov 12, 2008

Ad
  • 341 Answers

SOURCE: need plug gap for 2003 4.3 chevy truck

the plug gap is -- .060

Posted on Dec 06, 2008

  • 1596 Answers

SOURCE: ignition removal process for 1984 chevy 1/2 ton

This Outlines Removal Of Both LOCK CYLINDER<< Mechanical)) And The Ignition SWITCH ITSELF<< ELECTRICAL))

  1. Remove steering wheel as outlined previously.
  2. Remove turn signal switch as outlined in ``Turn Signal Switch, Replace'' procedure.
  3. Place ignition switch in ``Run'' position, then remove lock cylinder retaining screw and lock cylinder.
  4. To install, rotate lock cylinder to stop, while holding housing as shown, Fig. 6. Align cylinder key with keyway in housing, then push lock cylinder assembly into housing until fully seated.
  5. Install lock cylinder retaining screw. Torque screw to 40 inch lbs. for standard columns, or 22 inch lbs. for adjustable columns.
  6. Install buzzer switch, turn signal switch and steering wheel


CABALLERO, EL CAMINO, C, K, R, V & 1986---87 G MODELS
The ignition switch is mounted on top of the mast jacket inside the brake pedal support and is actuated by a rod and rack assembly.
  1. Disconnect battery ground cable.
  2. Disconnect and lower steering column. On some models, it may be necessary to remove the upper column mounting bracket if it hinders servicing of switch. Use extreme care when lowering steering column to prevent damage to column assembly. Only lower steering column a sufficient distance to perform ignition switch service.
  3. On Caballero and El Camino, rotate ignition lock to ``Off'' unlocked position.
  4. On C, K, R and V models, rotate ignition lock to ``Off'' locked position.
  5. If lock cylinder has been removed, pull switch actuator rod up to stop, then pushrod down to second (Caballero or El Camino) or first (C, K, R and V models) detent as shown, Fig. 7.
  6. Remove column mounted dimmer switch, if equipped, then remove switch retaining screws and switch.
  7. Reverse procedure to install, noting the following:
    1. Place gear shift lever in neutral.
    2. Place lock cylinder and switch in positions noted in steps 3 and 4.
    3. Fit actuator rod into hole in switch slider and secure switch with retaining screws, ensuring switch does not move out of detent.
    4. Install and adjust dimmer switch, if equipped, as outlined in ``Column Mounted Dimmer Switch, Replace'' procedure.
    5. Torque retaining screws to 35 inch lbs., then check switch operation.

Posted on Feb 21, 2009

  • 407 Answers

SOURCE: removal of 1976 chevy truck ignition switch

need a special tool to remove the locking plate behind steering wheel then pull turn signal switch back a little then remove screw that keeps lock cylinder in place

Posted on Oct 22, 2009

  • 3 Answers

SOURCE: need instructions on how to change ignition switch

how do i change the lock ignition on a 1986 chevy truck. got the lock ring off but the steering wheel will not come off

Posted on Nov 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a diagram of 1999 chevy 1/2 ton 4x4 rear brake brackets


Go to you nearest auto part. Store. They will print one up for you or when you get the kit it will diagram with it

Mar 06, 2013 | 1994 Chevrolet K1500

1 Answer

Wiring diagram for distributor on 1984 chevy k10 1/2 ton


i need a diagram for putting back together a steering column in a 1984 chevy

Jan 15, 2012 | Cars & Trucks

1 Answer

Where to plug in the wiper/cruise wire from the switch on 84 chev


i think its part of that long connector that goes to the ignition switch

Apr 25, 2010 | 1984 Chevrolet Chevy

1 Answer

My head lights only work when i keep the starter ingaged, also not charging. new alt batt and starter. 1984 chevy 3/4 ton


Replace the ignition switch,it only has aux.out put power in start position,not in the run position.

Jan 03, 2010 | 1984 Chevrolet C1500

2 Answers

Nned steerin column diagram


I don't have a diagram, But I have taken tons of these apart. Is there something I can help with?

May 04, 2009 | 1984 Chevrolet C1500

1 Answer

Chevy 1993 half ton 4 wheel drive


Is your 4x4 light coming on? Does the shifter move smoothly into position? I have a 95 that I have just about had every proplem imaginable. Need morre info. John.

Jan 10, 2009 | 1986 Chevrolet K1500

1 Answer

88 s10 pickup truck will not shift from 3rd gear to overdrive


need more info i had a 1984 chevy half ton and first, second, and third worked fine but lock up didnt work. the problem was there was no vacum at a switch under the hood on the fire wall also your shift linkage could be out of adjustment. try driving down the road and raise up a little on the shifter.

Nov 21, 2008 | 1988 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...