Question about Cars & Trucks

Open Question

What are ride height specs for 2005 9900i

Wheel hop, ride,...

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know the stock ride height for a 1998 gmc k2500 4x4?? Front and rear please


Exterior
Measurements
Width: 76.8 in.
Height: 76.0 in.
Length: 213.4 in.
Ground clearance: 7.3 in.
Wheel base: 131.5 in.

Jan 23, 2014 | Cars & Trucks

1 Answer

1997 cavalier, both rear tires wearing on the outside 1/2 of the tires. What would the probable culprit be? The car has 97k miles on it...


if you don`t rotate the tires this can cause abnormal tire wear.but with tire wear on the outer 1/2 of the tire indicates either the camber setting is off or you could have bad rear springs changing the ride height of the car causing the change in camber.to find out you would have to have a 4 wheel alignment done to check rear alignment readings.if the springs are worn then the ride height can be checked with a tape measure and compared to specs,if off then the springs should be changed along with the rear shocks.

Jun 29, 2011 | 1997 Chevrolet Cavalier

2 Answers

I want to know how to fix the alignment on my 1995 honda accord ex.


Before making wheel alignment adjustment, perform the following checks:
  1. Tires should be equal in size and runout must not be excessive. Tires and wheels should be in balance, and inflated to manufacturer's specifications.

  2. Wheel bearings must be properly adjusted. Steering linkage and suspension must not have excessive looseness. Check for wear in tie rod ends and ball joints.
  3. Steering gear box must not have excessive play. Check and adjust to manufacturer's specifications.
  4. Vehicle must be at curb height with full fuel load and spare tire in vehicle. No extra load should be on vehicle.
  5. Vehicle must be level with floor and with suspension settled. Jounce front and rear of vehicle several times and allow it to settle to normal curb height.
  6. If steering wheel is not centered with front wheels in straight-ahead position, correct by shortening one tie rod adjusting sleeve and lengthening opposite sleeve equal amounts.
  7. Ensure wheel lug nuts are tightened to torque specifications
Ride Height Adjustment

Before adjusting alignment, check riding height. Riding height must be checked with vehicle on level floor and tires properly inflated. Passenger and luggage compartments must be unloaded. Bounce vehicle several times, and allow suspension to settle. Visually inspect vehicle from front to rear and from side to side for signs of abnormal height.
Measure riding height. See figure. Riding height between left and right sides of vehicle should vary less than 1′ (25.4 mm). If riding height is not within specification, check suspension components and repair or replace them as necessary.
Wheel Alignment Procedures

Honda recommends using commercially available computerized 4-wheel alignment equipment. Follow equipment manufacturer instructions to obtain vehicle alignment settings. Use following procedures for necessary adjustments.
Civic Camber Adjustment
Compare camber settings with vehicle manufacturer recommendations. If camber is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck camber.
Civic Caster Adjustment
DO NOT use more than 2 shims. If more than 2 shims are required to adjust caster angle, check for bent or damaged suspension components.
Compare caster settings with vehicle manufacturer recommendations. If caster is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck caster.
Civic Toe-In Adjustment

  1. Secure steering wheel in straight-ahead position. Measure front wheel toe-in. If adjustment is needed, loosen tie rod lock nuts. Turn both tie rods equally in the same direction until front wheels are in straight-ahead position and toe-in reading is correct. Tighten tie rod lock nuts. Reposition tie rod boots if twisted.
  2. Ensure parking brake is released. Check rear wheel toe-in. If adjustment is needed, hold adjusting bolt on rear compensator arm and loosen lock nut. See figure. Adjust rear toe-in by sliding rear control arm until rear toe-in is correct. Install NEW lock nut, and tighten it while holding adjusting bolt.
Wheel Alignment Specifications

  • Camber - Measurement in degrees.
    • Front: 0 (range -1 to 1)
    • Rear: 0.33 (range -1.33 to 0.67)
  • Caster - Measurement in degrees.
    • 1.17 (range 0.17 to 2.17)
  • Toe-In - Measurement in inches (mm).
    • Front: -0 (0)
    • Rear: 0.08 (2.0)
  • Toe-In - Measurement in degrees.
    • Front: 0.00 (range - 0.16 to 0.16)
  • Toe-Out On Turns - Measurement in degrees.
    • Inner: 41.00
    • Outer: 33.50
Torque Specifications Ft. Lbs (N.m)

  • Rear Control Arm Adjusting Bolt: 48 (65)
  • Spindle Nut: 136 (185)
  • Tie Rod Lock Nut: 41 (55)
  • Wheel Lug Nuts: 80 (108)
hope this helps you out.

May 09, 2011 | 1995 Honda Accord

1 Answer

Back end car is too low


measure your ride height and compare to maufacturer specs..
make sure the corerect tire siz and rims are equipt on this vehicle
make sure vehicle load capacity not exceeded. if all the above checks
out look for lowering springs may have adjustable ride height if not
then the springs are sagging as this also will effect ride height.

Apr 15, 2010 | 2004 Nissan 350Z

2 Answers

99 expedition two wheel drive passenger side goes up higher than the drivers side.uneven ride! whats a ride height sensor?


height sensor is a sensor that control air compressor on air shock.it keep vechicle level.if height sensor senses distance between frame and suspension .it will admit air to shock by controling the air compressor.check the air shock on driver side.BESURE TO TURN OFF ELECTRICAL POWER TO AIR SUSPENSION BEFORE RAISING VECHICLE.

Jul 10, 2009 | 2000 Ford Expedition

1 Answer

Wheel alignment for automobile


Hello. Wheel alignment is the adjustment of the front and rear wheels so that they are correctly inline with each other and pointing straight forward. If they point to the left or right the car will pull to that side of the road while being driven. The front wheels also need to be adjusted to ensure they are not too far forward and riding on the back of the tire, or not too far back and riding on the front of the tire. Lastly, all tires need to be checked to ensure they are not leaning too far in or out of their wheelwell, causing the tires to become prematurely bald. For most vehicles it can cost you $40-$120 depending where its done, plus any shim kits needed to adjust the wheel allignment back to factory specs. Most shops provide 2 or 4 wheel alignment, so always ensure that they perform a 4 wheel alignment. Always ask for the alignment test reports for both before and after the work is performed so you can see for yourself which were out of alignment. Pot holes, curb-hopping, railroad/railway tracks, etc. play a huge part in your vehicle alignment going bad. 4 tires on some cars can cost you $500-1600 to replace, but an alignment check every 2-4 years will only cost you a very small amount, saving you time and money.

Apr 03, 2009 | 2000 Mini Cooper

1 Answer

EXPEDITION REAR AIR RIDE PROBLEM


do you have just rear air suspension? here's rear only. 4 wheel different. Deler an run a diagnostic test with WDS machine and get fault codes.
-------------------------------------------------------------------------------------
The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving conditions:
  • Ride is improved by using an air type spring (the soft ride is inherent).
  • Handling is improved by maintaining constant vehicle attitude.
The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed or the vehicle speed exceeds 16 km/h (10 mph).
----------------------------------------------------------------------------------------
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level
------------------------------------------------------------------------------
  • Uneven vehicle height
  • Circuitry.
  • Rear pneumatic fault.
  • Air compressor assembly.
  • Air suspension control module.
  • Go To Pinpoint Test I .

Feb 21, 2009 | 2001 Ford Expedition

1 Answer

I would like to know the factory ground clearance for my 96 olds model 98. Thanks Art


hi art , i think they are going to call it ride height in the alignment specs . front ride height would be 9.0" - 9.8" and that point of measurement would be taken at the rocker panel 23.5" back from the center of the front axel (center of tire) to the bottom of the rocker panel .and the rear height would be 9.05" - 9.85" , and that point of measurement would be 23.5" from the center of the rear axel forward to the bottom of the rocker panel .see pic
4b869e6.jpg
4f228d0.jpg
J5

Jan 20, 2009 | 1996 Oldsmobile Ninety Eight

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13723 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...