Question about 1993 Isuzu Trooper

1 Answer

Where do I find the data link connector - 1993 Isuzu Trooper

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

It is on the left side of the passenger foot well, front seat.

Posted on Mar 03, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why would a data link connector stop working


Has it ever worked? Possibility no positive supply or ground at data link connector. Need to locate a wiring diagram for your connector. Try google.if you don't have a diagram.

Jul 07, 2012 | 1994 Dodge Stealth

1 Answer

I need to find the obd connector plug


Data Link Connector The Data Link Connector (DLC) may be found in the following location:
  • Under the driver's side dashboard, near the steering column.
The DLC is rectangular in design and capable of allowing access to 16 terminals. The connector has keying features that allow easy connection. The test equipment and the DLC have a latching feature to ensure a good mated connection.

Oct 12, 2010 | 1993 Lincoln Mark VIII

1 Answer

No obd signal


check fuse #17 in the passenger compartment fuse box, it is the power supply for the data link connector

Fuse 17 a 20A (Cigar Lighter, OBD2 Data Link
Connector)

Sep 29, 2010 | 2001 Ford Explorer Sport

1 Answer

When check engine indicator light came on in 1997 dodge grand caravan on and p1698 troubleshooting code appears, what does that mean?


The P1698 code means that no digital data is being received by the powertrain controller (on the left inner fender) from the transmission control module, located on the right inner fender. The manual says to check the ccd bus wires between the module and the rest of the system using the Chrysler diagnostic readout box. But if you don't have one then I think you can do the same thing by measuring for continuity (near 0 resistance) between pin 4 of its plug and pin 11 of the data link plug under the dash .
Then check the resistance between pin 43 if its plug and pin 3 of the data link connector. Finally check continuity from pin 7 of the data connector and pin 65 of the powertrain connector (pink wire). If the continuity between the transmission and data link connector wires checks as well as from the connector to the PCM proves to be ok, then according to the manual the trans controller should be replaced. But you should also verify that there is either a + or - bias voltage of 2.5 volts on each of those wires as a loss of bias voltage will also cause this code.

Jul 09, 2010 | 1997 Dodge Grand Caravan

1 Answer

Troubeshooting code p1698 for 1997 dodge caravan?


The P1698 code means that no digital data is being received by the powertrain controller (on the left inner fender) from the transmission control module, located on the right inner fender. The manual says to check the ccd bus wires between the module and the rest of the system using the Chrysler diagnostic readout box. But if you don't have one then I think you can do the same thing by measuring for continuity (near 0 resistance) between pin 4 of its plug and pin 11 of the data link plug under the dash .
Then check the resistance between pin 43 if its plug and pin 3 of the data link connector. Finally check continuity from pin 7 of the data connector and pin 65 of the powertrain connector (pink wire). If the continuity between the transmission and data link connector wires checks as well as from the connector to the PCM proves to be ok, then according to the manual the trans controller should be replaced. But you should also verify that there is either a + or - bias voltage of 2.5 volts on each of those wires as a loss of bias voltage will also cause this code.

Jul 09, 2010 | 1997 Dodge Caravan

2 Answers

Where do i find the dlc plug


PLEASE DON'T FORGET TO RATE!!!! Data Link Connector OBD II Systems use a standardized test connector called the Data Link Connector (DLC). It is located beneath the instrument panel somewhere between the left end of the instrument panel and 12 inches (300 mm) past the vehicle centerline.
The DLC is located out of the sight of vehicle passengers, but should be easily viewable by a technician from a kneeling position outside the vehicle. The DLC is rectangular in design, capable of accommodating up to 16 terminals and has keying features to allow for easy connection. The DCL and Scan Tool connector have latching features that ensure the Scan Tool connector will remain mated when properly connected. Some common uses of the Scan Tool are:
  • To identify and clear any stored diagnostic trouble codes
  • To read the serial data stream information (e.g., PID data)
  • To perform Enhanced Diagnostic Tests (bi-directional Scan Tool)
96d7723.gif
Data Link Connector Graphic

Nov 01, 2009 | 2002 Oldsmobile Alero

1 Answer

Trying to find where the data link connector is located, because i was told it was bent and i need to fix it.


if data link connector its below the steering wheel kinda of by brake area its a black connector

Oct 16, 2009 | 2002 Nissan Xterra

2 Answers

Engine light blinks on 1995 Model, already replaced spark plugs and wires


you need to connect the data link connectors underneath the steering wheel, then turn ignition on and count the flashes that the engine management light blinks..Post back

Aug 13, 2009 | 1995 Subaru Impreza

1 Answer

I cant find the data link connector


its in the center console. pull out the ash tray and its right under it

Jan 16, 2009 | 1994 Honda Passport

1 Answer

Can't find data connector for programming key fob


Your data link connector should be under the dash on the driver side.

Jun 21, 2008 | 1996 Buick Riviera

Not finding what you are looking for?
1993 Isuzu Trooper Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...