Question about Cars & Trucks

Open Question

How much torque for tight of hiace 2002 front wheel bearing

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: 2002 ford explorer front wheel bearing assembly

remove hub ,take retaining circlip out and knock it out with a big big hammer supporting it on an old wheel rim and a tree trunk.this job is easy to do but unless you have the right tools entrust it to a garage who will have a nice press .

Posted on Feb 02, 2009

  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

  • 583 Answers

SOURCE: need torque setting for 1993 geo tracker front

i1m sorry to say that wheel bearings are not set to a torque specification, when you have repacked the bearings [ inner and outer ] ,reassembled it ,take the nut up until thewheel starts to drag and not turn very far when you try to spin it spin it backward and forward several times,grab the top of the wheel and try to push it in and out,if you getany movement at all tighten the nut a couple of castilations. do it all over again, spinthe wheel a few times and then try for the crossways movement again, if there is no movement ,you are very close to being right....................now comes the experience bit , iwould take it one more castilation of the nut because i know the feel that is need ed,,without that i suggest you put the pin in where you ereput the cap on and go for a 5 minute drive . whenyou get back ,jack it up and thespinning of the wheel again and try for the top crossways movement ,if there is any tighten thenut 2 castilations, and provided that when you try to spin the wheel by hand with a reasonably strong push the wheel should trael about 6 inches at least after your hand leaves it ,it is now a close as you are going to get itput it all to gether and for the next day or so put yor hand on the grease cap after you have driven anydistance, and you will feel it is warm but you should be able tohold your hand on the grease cap. there you have it ,any questions come back."youdoit"

Posted on Nov 06, 2009

  • 10 Answers

SOURCE: what is the torque specs for the front wheel

Ford Front wheel bearings do have a torque spec. It is all over the new part to torque to MFR spec or damage will occur.
I have no idea what that spec is though.

Posted on Nov 07, 2009

  • 2 Answers

SOURCE: How to replace front wheel bearing on a 2002 Dodge 1500

You take off the right tire. You have take all the bolts out from underneath the

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can i adjust 2006 toyota hiace front wheel bearing


Hey Trevor, Whats going on that you think your front wheel bearing needs adjusting?? Is this a front wheel drive?..If your wheel is loose, you NEED to take this to a qualified professional!!

Jul 06, 2017 | Toyota Cars & Trucks

1 Answer

2002 pt cruizer changed both front wheel bearings and long axle rightside now there is a humming noise on drivers side when driving and ideas thanks


It is entirely possible to have a bad replacement wheel bearing. There are many cheap ones available and I've found that you get what you pay for. I prefer Timken bearings myself. Also, the drive axle nut torque is critical in ensuring that you don't cause bearing failure. Too loose or too tight will cause bearings to fail in short order. The axle nut is not one that can be "shade tree torqued" by "grunt-power".

Jun 29, 2015 | Cars & Trucks

1 Answer

Repair hud assenbly front


If you are talking about the front wheel hub assemblies, the bearing is pretty difficult to replace. It can not be repaired or adjusted.

I have a 2002 Escape and have replaced the front wheel bearings. Here are some instructions and pictures:

I have a 2002 Escape and have changed my bearings. The front wheel bearings on the Escape are simple cartridge bearings, or Gen1 bearings, that are pressed onto the hub and knuckle. They are not so simple to replace. Unless you have the experience and tools, you'll need to take it to the dealer or a shop.

You will need a press and the correct press tools.
The knuckle/hub assembly needs to be removed from the vehicle.

Here's the short version:
Remove the tire/wheel.
Remove the brake caliper w/ bracket.
Remove rotor.
Remove the ABS sensor.
Remove axle nut and press the axle inwards, until loose. (sometimes easy, usual needs special tool).
Remove the strut bolts, tie rod, and the lower ball joint from the knuckle/hub assembly. Each of these connections can have it's issues.
Press the hub out of the assembly. One half of the inner race will be stuck on the hub. Use a bearing splitter to remove that half.
Remove the snap ring from the knuckle.
Press the rest of the bearing from the knuckle.
Press the new bearing into the knuckle. Press on the outer race only!
Snap ring.
Make sure the dust sheild is still in place.
Press the hub into the bearing. The bearing must be supported on the inner race only!
The point is that you must not press thru the balls in the bearing. That can cause the bearing to get brinnelled.... not good.
Reassemble the knuckle on the vehicle in reverse order. I like to put a little grease on the axle spline. The axle spline has a little helix on it... about half a degree. It's supposed to be a tight fit. The torque on the axle nut is 300Nm (about 220ft-lbs?). This torque is very, very important. It is needed to keep the bearing together and at the correct preload, so use a big torque wrench.

...or you can take it to the dealer.

Good luck.

cimg1162.jpg
cimg1165.jpg
cimg1256ss.jpg
cimg1241.jpg

Dec 30, 2010 | 2003 Ford Escape

1 Answer

Front bearing nut torque specification rear wheel drive?


front bearing wheel nut holding axle on? 115 foot pounds and hammer in or crimp the nut after tightening. ^ like shape into slot of axle this locks the axle. for the wheel bearing for rear wheel drive the nut should be tightened by hand till tight 15 foot pounds then backed off 1/4 turn, be sure there is plenty of grees in the bearing cup before tighting nut be sure to line up slot for key with rotor on the rotor should turn free and should not have any slop in it, put the wheel on it and put the nuts on and try wiggleing the wheel back and forth if any movement readuast nut. If it is to tight it will over heat outter wheel bearing, also be sure there is greese in inner wheel bearing.

Jul 14, 2010 | 2000 Mercury Grand Marquis

1 Answer

What are the wheel bearing torque specs on an 87 ford f150 4x4


torque specs dont really work with wheel bearings,its better to do it by feel,front wheel bearings with ratchet nuts,----usually tighten good and snug by hand and tap on the rotor a few times to seat the bearings,then good and snug again,not really hard,and back off 1/8 to a 1/16th of a turn,then tighten with your hand until it stops freely..you just dont want them too tight to wear out the new bearings

Feb 14, 2010 | 1987 Ford F 150

1 Answer

2002 chev impala, what is the torque spec on front hubs with abs


if they are the bolts that hold the hub and bearing in place just get the as tight as you can like putting lug nut on your wheels. if it's the axle nut just go as tight as you can by hand or impact gun

Jan 11, 2010 | 2002 Chevrolet Impala

2 Answers

What is the torque specs for the front wheel bearing/hub assembly nut on a 2002 ford mustang?


Wheel bearing don't have torque specs (to the best of my knowedge). They have a procedure - in this case it is....
1. With everything clean and packed with grease, snug the bearing lock nut until it stops.
2. Reverse it about 1/8th to 1/4 turn and insert the cotter pin.
Done

Oct 11, 2009 | 2002 Ford Mustang

1 Answer

Need wheel bearing torque


Spin the rotor and tighten the castle nut untill tight. go tighter untill your carter pin hole lines up with the castle nut.

May 19, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...