Question about Hyundai Cars & Trucks

Open Question

Thrust bearing fora hyundai getz

How much is a thrust bearing and how many hours to fit one

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 53 Answers

SOURCE: hyundai getz

if the speedo still works then it will need a spedo unit if the speedo doesn't work it is either the cable or the gear in the trans to check the cable unthread from trans and attach a drill to the cable innereds spin the drill if the speedo does not move replace the speedo cable

Posted on Oct 18, 2008

  • 138 Answers

SOURCE: Hyundai Getz - Passanger airbag or not...

If it says "airbag" on the stering wheel AND on the dash in front of the passenger,then it has a passengers side airbag.
Children are much safer in the back seat in the event of a collision.

Posted on Jul 02, 2009

Danniboi
  • 1098 Answers

SOURCE: Hello I have just had a new clutch fitted into my

if you used the car with a bad cluth you may have damaged the syncromesh, it nearly always happens in 3rd gear. Sounds like the fault, the syncromesh is part of the gearbox and most often cannot be fixed without a new gearbox.

Posted on Jan 13, 2010

Testimonial: "Great thank you"

  • 566 Answers

SOURCE: logbook service for a hyundai getz

hi from uk did you not recieve the wallet containing the owners handbook/service reciord book/ radio instructions book? this comes with car if you bought new ? check with dealer and ask for it? there is a market for these books and are valuable yours may have been taken ??

Posted on Mar 10, 2010

emissionwiz
  • 75822 Answers

SOURCE: how do you secure the thrust bearings? are they fitted either side of 3rd journal?

Use thick grease like wheel bearing grease.

Posted on Jul 12, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Daughters 2002 Hyundai Getz is stuck in what i think is second gear.


Worn Clutch plate or thrust plate.

Check if hydraulic Clutch
if so check clutch fliud level . Could be a faulty clutch master cyclinder in hydraulic system.

Jan 15, 2015 | 2002 Hyundai Getz

1 Answer

What could cause a low pitched humming when excelerating in a 2006 huyandi getz.?


A wheel bearing maybe, or in a manual, the gearbox first motion bearing.

Another candidate is the differential, but in a FWD car this is usually nothing to worry about.

Dec 13, 2014 | 2006 Hyundai Getz 1.4

1 Answer

Hyundai getz starting problem


run the fault codes and find exactly which sensor should have been fitted

Mar 08, 2014 | Cars & Trucks

1 Answer

How can i tell if my wheel bearings need to be replaced without pulling off parts for hyundai getz 2002


Sound comparison.
Jack up one front wheel, and securely block the other 3 wheels. Start the engine and put the car in gear, and let the motor run the wheel .
Do not race the engine.
Listen to the sound it makes.
Now shut off the engine and do the same to the other front wheel.
Is one really noisy ?
That's the problem wheel.
Unless you car was in a flood, wheel bearings usually last a lifetime on most cars.
Be blessed.

Feb 17, 2013 | 2002 Hyundai Getz

1 Answer

Torque settings for 1.4 hyundai getz , main bearings


I need torque settings on hundai getz 1.4 Mains and big ends

Oct 20, 2012 | 2006 Hyundai Getz 1.4

1 Answer

Disable hyundai getz alarm


To disable the alarm on a Hyundai Getz, you just need to bypass the hood switch. The alarm circuit thinks the hood is up and will not go into the Arm state.

The switch connects the single wire connected to it to ground when the hood is up.

So you can just connect a wire from the back of the switch to ground. You can fit a switch to enable/disable the alarm if you wish.

This is equivalent to just locking/unlocking the car manually with the key.

Jul 07, 2012 | Hyundai Getz Cars & Trucks

1 Answer

Hello I have just had a new clutch fitted into my Hyundai Accent Coupe (2000) and yet the thrust bearing is still noisy and it is notchy going into 2/3 gears and when dropping down from 5th to 4th - any...


if you used the car with a bad cluth you may have damaged the syncromesh, it nearly always happens in 3rd gear. Sounds like the fault, the syncromesh is part of the gearbox and most often cannot be fixed without a new gearbox.

Jan 13, 2010 | 2000 Hyundai Accent

2 Answers

I have a 2005 Hyundai Elantra manual and when it is idling, it makes a rattling sound in the engine. The noise goes away when I push in the clutch or when I rev the engine. Just wondering what it is and...


Check your gearbox oil level.If thats ok.Then you have a problem with the thrust bearing either worn or dry.The only solution is to fit a new clutch kit.Hope that was helpfull

Jul 24, 2009 | 2005 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...