Question about Mazda Cars & Trucks

Open Question

Added cruise control kit 250-9502 to my 2010 mazda 3 and it isn't working showing low voltage to gas pedal

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Cruise Control Issue

The most common solution is to replace the brake light switch . The switch has 3 sets of contacts one set is for the cruise control. If the cruise control part is at fault the cruise control will not engage. The switch typically costs from 10 to 15 dollars.

Posted on Dec 25, 2008

  • 1 Answer

SOURCE: 2003 nissan altima heater blowing cold air

Replace your thermostat

Posted on Jan 23, 2009

mnabi01
  • 94 Answers

SOURCE: 2004 mazda 3 stalls off idle

i found out from dealer there was a service bulitan for this problem. mazda reprogram the ecm for idle speed contorol . problem solved.

thank you

Posted on Jan 28, 2009

  • 51 Answers

SOURCE: 1998 dodge grand caravan cruise control not working

does the horn work and is the air bag light on because if thats the case you have a bad clockspring. and for your year van i do belive that is a lifetime recall. hope this helps.

Posted on Mar 16, 2009

Hrnsly
  • 154 Answers

SOURCE: the cruise control is not working 2002 Mazda Tribute

you have a bad cruise cable, this is a very common problem with the tribute. just go to your local dealer and have them replace it for you, it only takes about 30 minutes to do

Posted on Aug 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 impala 3.5 LT check engine and service traction control? Code: P2138


DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation
Electronic throttle control problem .
The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system includes the following components:
• The accelerator pedal position (APP) sensors
• The throttle body assembly
• The engine control module (ECM)

Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Search P2138 on youtube ,will show diagnostic steps .

Aug 19, 2017 | Cars & Trucks

2 Answers

2007 rav 4 cruise control no work


First thing to check is fuses, then the brake pedal "Kick Out" switch that can often come loose or out of adjustment, next relay, next actuator.

Oct 03, 2016 | 2007 Toyota RAV4

1 Answer

My cruise control is not working....is that a fuse problem....also does a light come on when low on gas?


The cruise control light blinks when there is a problem with it.

Here's a link for a kit that repairs the Subaru 1997-1998 Cruise control system if not working:
http://www.mnrelectronics.com/sucrco1.html

Aug 02, 2010 | 1997 Subaru Impreza

2 Answers

I own a 2005 GMC Canyon Five CYL and the cruise control stopped working last niight. You push the button and no cruise. I checked the fuse and it is ok I exchanged with another 10AMP and no change still...


Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .

Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

Apr 01, 2010 | 2005 GMC Canyon

2 Answers

Cruise control problem


There are 3 places on the Rav4 where fuses can be located and checked. for the cuise control.

The back of the cruise control stacking switch has been know to fail (fall apart) and Toyota issued a TSB with replacement switch.

if it is the fuses then they most likely are related to cruise control system: Stop, Dome, Gauge and Igniton
The interior fuse box
The main engine fuse box (by brake fluid)
Cruise control ECU is under the glovebox.
Cruise control actuator is under hood (by driver side brake fluid/booster)Throttle position sensor (to detect if your foot is on gas pedal)
Cruise control switch on the clutch pedal too (if you have 5spd manual)
Brake lights are the deactivate signal for the cruise control


Aug 13, 2009 | 1998 Toyota RAV4

1 Answer

Cruise control indicater lights are on but will not engage


Check the cruise control module connector, see if it looks good and there is power to the module over one of the white wires in the 10 pin connector.
There are two white wires going to the module which is located at pins "G" and "J". There should be no voltage at pin "G" until the brake switch is applied. This switch is also used to operate the brake lights. The two wire colors on this switch are white and orange. At pin "J", this signal goes to the PCM to tell it that the cruise control module is engaged. Here is the info on the cruise control connector:

Pin A: gray - cruise control on switch signal: 12VDC with cruise switch on
Pin B: dark blue - cruise control set/coast switch signal: 12VDC with switch pressed
Pin C: gray/black - cruise control resume/accel switch signal: 12VDC with switch pressed
Pin D: brown - cruise control release signal: 12VDC with brake pedal not pressed: 0V when pressed
Pin E: black/white - ground
Pin F: brown - ignition 3 voltage: 12VDC with ignition on
Pin G: white - stop lamp switch signal: 0V with brake pedal not pressed: 12VDC when pressed
Pin H: dark green - cruise control inhibit signal: 0V if PCM detects an inhibit condition
Pin J: white - cruise control engaged signal: voltage (unsure of value, either 12VDC or 5VDC) when signal engaged
Pin K: dark green - vehicle speed signal: 1 to 5 volts depending on speed

This view of connector is facing it after it is separated.

Trying to post the connector view, the lines may not quite line up, but at least it should show you the pin positions.

| F  G H J K |

| E D C B A | 

May 09, 2009 | 2002 Chevrolet Impala

1 Answer

I do not know where the cruise control is located Mazda Miata


Main Switch Is Located LEFT of Steering Wheel Down Low and there are 3 Switches and Cruise switch is the One on FAR LEFT

Mar 29, 2009 | 1997 Mazda MX-5 Miata

1 Answer

Cruise control turns off when using turn signal. Just install trailer wiring harness. 2007 Mazda 3 with LED tail lights


If this problem was not there before you installed LED lights that may be the cause, there may be a electrical spike from the LED high voltage circuit that turns the cruise off, you might want to call the tech support of the company that made the LED light kit.

Nov 02, 2008 | Mazda MAZDA3 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...