Question about 2001 Chevrolet Silverado 1500

Open Question

3 wires pulled from plug

Above starter on block is a 3 wire plug which i pulled 3 wires out,what order do the wires get replaced?colors are blue,green,and yellow

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tepfy
  • 319 Answers

SOURCE: Where do color wires connect on crank position sensor Chevy 2000?

http://www.autozone.com/N,317019/initialAction,repairGuide/shopping/repairGuideVehicleSelect3.htm

follow this and figure out what truck you have. then put in the part you want and go to repair info on the left. It should give you the diagram you need.

Posted on Dec 20, 2008

  • 1608 Answers

SOURCE: wires pulled out of crank sensor plug yellow blue

The yellow goes on the terminal B.Blue to terminal A AND green to terminal C.You should be able to see the letters on the connector.Good luck.

Posted on Nov 19, 2009

bluesman1956
  • 388 Answers

SOURCE: the plug above the starter on the block came loose

If by "plug" you are referring to a plastic cap, that would be the end off you starter solenoid. The best thing to do would be to replace the solenoid and reattach the wires to the new one. Be sure to remove the positive battery cable before attempting this. If you are unsure how to replace the solenoid it may be easier to replace the entire starter with a rebuilt one that can be found at any auto parts store. Please rate this answer,thanks.

Posted on Feb 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my 1992 ford festiva firing in the order 1-2-3-4 and not 1-3-4-2?


Your order is wrong, and you need to switch the wires around on the top of the distributor. First pull the distributor cap off to find direction of rotation (some distributors turn clockwise, and some turn counterclockwise). Watch the rotor, the black bar on top of distributor shaft, and note it's direction of travel while someone bumps the starter over with the ignition switch. Now you can put the dist. cap back on, and arrange the spark plug wires in order 1-3-4-2. Leave number 1 in place, if it is marked as 1 on the cap. The plug wires can be pulled out of the raised terminals in the distributor cap for setting them in order. Just be careful of pulling too ******* the wires, you can cause them to break internally. Twist them back and forth first to loosen them, and gently pull them out, using the plug wire's rubber boot if possible to pull on them.
If it is easier to pull the sparkplug wires off the spark plug, rather than the distributor cap, you could set the order that way. Just need to know the direction of rotor travel. Number1 will go to cylinder 1, and next in order will be number 3, following direction of rotation, so that wire goes to cylinder 3, and on to 4, then 2.
Post back if you need more help. Good luck.

Jul 02, 2012 | 1992 Ford Festiva

1 Answer

The plug above the starter on the block came loose all 3 wires came out of the plug. Tried to put them back the starter comes on and won't shut off. the wires are all brown in color. 2003 express van 6.0...


If by "plug" you are referring to a plastic cap, that would be the end off you starter solenoid. The best thing to do would be to replace the solenoid and reattach the wires to the new one. Be sure to remove the positive battery cable before attempting this. If you are unsure how to replace the solenoid it may be easier to replace the entire starter with a rebuilt one that can be found at any auto parts store. Please rate this answer,thanks.

Feb 01, 2011 | 2003 Chevrolet Express

1 Answer

How do you check the firing order on a chevy small block engine ?


Firing order for small block chevy is 1-8-4-3-6-5-7-2. The cylinders are numbered 1-3-5-7 on the driver's side of the engine counting front to back. Passenger side is 2-4-6-8, front to back. You will need to get #1 cylinder at top dead center on the compression stroke. To do this, remove the #1 spark plug and remove the coil wire from the distributor cap. You will need a helper for the next step. Place your index finger in the empty spark plug hole, Have your helper bump the starter with the ignition key, When #1 cylinder comes up on the compression stroke, the pressure will push your finger away from the spark plug hole. Don't worry, this doesn't hurt. Turn the key off. Check the timing mark on the harmonic balancer behind the crankshaft pulley. It should be pretty close to lining up with the "0" timing mark on the pointer attached to the engine block. Now pull the distributor cap and see where the rotor cap is pointing. This will be #1 on the distributor cap. The spark plug wire from the #1 plug will occupy that position. The next position on the distributor cap will be for the plug wire coming off the #8 cylinder. The rest of the plug wires will attach to the distributor cap in the above mentioned firing order counting clockwise. If you do not wish to place your finger in the #1 spark plug hole, you can use a piece of paper towel roll up and stuck in the hole just enough to form a seal. When the piston comes up on the compression stroke it will force the paper towel out. Any questions, just let me know.

Dec 30, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

Removing a starter from a 94 new yorker


  • Check the condition of the battery. A weak battery can't turn the starter over. Make sure the battery is at full strength before you blame the starter. Your car's instrument cluster should indicate when there is a low battery with either a warning light or ammeter.
  • Also check the battery connections, the wires going to the starter, and the starter connection. The most important wire is the big one running down the back of the battery. It is the wire that goes from the battery to the starter. All connections should be snug. Check that the insulation on the wires is intact. Tighten any connections loose enough to wiggle by hand.
  • Check the starter solenoid. The starter solenoid is a special switch that turns the starter on and off. Solenoids rarely cost more than $10, and they are fairly easy to replace. When you turn the key, have a friend listen to the solenoid for a clicking sound. If there's no sound, assume the solenoid is broken and needs to be replaced.
  • If the automotive engine is turning over and still won't start, it might be due to another problem unrelated to the starter or battery. Anything from a dirty air filter, worn spark plugs, bad spark plug wires, a worn distributor cap, insufficient fuel reaching the engine or even blown gaskets can prevent a car from starting. If you can't isolate the problem through trial and error, it may be time to take the car to a mechanic for check-up or repair.

Once you've determined that the problem is not resolved by troubleshooting the above issues, it may very well be that you need to replace the starter.

  1. Disconnect the battery cables in order to reduce the possibility of accidentally shocking yourself.



    #block-google_admanager-1 { margin-left: -22px; }
  2. Remove the electrical connections from the side of the starter. There are usually two wires: a positive and a negative wire. Remove the positive wire first, and then remove the negative wire from the starter. You may want to mark the connections with a paint pen to help you correctly reconnect the connectors to their proper terminals. To remove the connections, you'll need to use an open face wrench or socket wrench to remove the bolts.
    After both of the electrical connections are removed, you'll need to unbolt the starter from the chassis. Before you remove these bolts, take note of how the starter is oriented. You may want to mark the bolts with paint pens. There are usually only two or three bolts that attach the starter to the vehicle.
  3. Remove the starter. In preparation, look closely at your car and determine what path will be easiest for removing the starter. It might be a tight fit, but you'll need to twist and pull the starter around various engine and frame parts in order to get it out of the car. Some cars may be particularly tight, especially those with front wheel drive. You may have to remove other parts in order to get enough space the pull the starter out. If you do remove engine parts, take care to remember their proper location. Replace bolts into the same place they came from once you pull a piece off. This will help you keep up with all of the pieces.
  4. Once you've pulled the starter out, you can put the new starter in its place. You'll need to put it back in the exact same way you pulled the old starter out. Once you have it in place, put in a bolt just enough to hold the starter in place. Then connect the electrical connections beginning with the ground wire. Once the ground wire is connected, attach the rest of the wiring. Next, install the rest of the bolts holding the starter to the frame. Check to see that all bolts are tight.

Dec 10, 2010 | 1994 Chrysler New Yorker

1 Answer

Replace starter how do i do this


REMOVAL & INSTALLATION
(see Figure 3 to 6)
  1. Disconnect the negative battery cable.
  2. Raise the front of the vehicle and install jackstands beneath the frame. Firmly apply the parking brake and place blocks in back of the rear wheels.
d07c224.jpg

Fig. 3: Disconnect all wires connected to the starter, including this ground wire on the starter moutnting bolt stud
  1. Tag and disconnect the wiring at the starter.
WARNING When detaching the hardshell connector at the S-terminal, grasp the plastic shell to pull it off. Do not pull on the wire itself. Ensure to pull the connector straight off to prevent damage to the connector and S-terminal. If any part of the connector is damaged, replace the damaged component.
bce654f.jpg

Fig. 4: Some starters use a self-threading bolt to hold the starter cable

8eafc80.jpg

Fig. 5: Remove the starter motor (arrow) mounting bolts ...
  1. Remove the starter mounting bolts and remove the starter.
a87aff9.jpg

Fig. 6: ... then remove the starter-be careful, the starter motor can be quite heavy

To install:

  1. Position the starter motor against the engine and install the mounting bolts. Tighten the mounting bolts to 15-19 ft. lbs. (21-27 Nm).
  2. Install the starter solenoid connector by pushing it straight on. Ensure that the connector locks in position with a notable click.
Install the starter cable nut to the starter solenoid B-terminal. Tighten the nut to 80-123 inch lbs. (9-14 Nm).
  1. Connect any remaining wiring to the starter motor.
  2. Lower the front of the vehicle and remove the wheel blocks.
  3. Connect the negative battery cable.

Hope this helps: remember rated this.

Aug 11, 2010 | 1995 Ford Explorer

1 Answer

Crankshaft sensor location on 2001 oldsmobile


. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wIre CONNECTOR plug to the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery.

Jun 05, 2010 | 2001 Oldsmobile Intrigue

1 Answer

Where is the crankshaft position sensor located?


This is a quick answer. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wore plug into the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery.

Jun 05, 2010 | 2000 Oldsmobile Intrigue

1 Answer

HOW DO YOU REPLACE A STARTER FOR 1991 CHEVY LUMINA


1) Disconnect cable from negative battery terminal
2) Raise vehicle front and suitably and safely support.
3) Remove cover from starter wiring (small right angle-like black plastic cover).
3) Loosen large wiring harness (underneath starter) so that it can be moved out of the way.
4) Remove outer nut and wires from solenoid.
5) Remove outer nut and wires wires from starter.
6) Remove two (2) screws retaining plastic flywheel cover and cover. You will need to do this - otherwise you will be unable to remove the front bolt holding the starter to the engine block. This cover is a small black plstic piece located where starter penertates the flywheel cover.
7) Remove (2) bolts retaining starter to the engine block. One is accessable towards the front of the starter/vehicile and the other (long one) is towards the rear of the vehicle - just behind the frame cross member.
8) Position starter so that if can be dropped down (flywheel gear part first).
9) Reverse the above instructions to install the new starter/solenoid

Dec 22, 2009 | 1991 Chevrolet Lumina

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...