Question about Toyota Cars & Trucks

Open Question

Replace blend door actuator motor

How to Replace the blend door actuator motor on 07 Toyota tundra

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michael_grey
  • 365 Answers

SOURCE: cold air on passenger side warm air on drivers side

Actuator motors either get a tear in the rubber or a hose is broken and not letting vacuum assist in its opening.
You can try moving the lever by hand and see if the air gets colder on the bad side.c976077.jpg

Posted on Aug 04, 2009

Ad
  • 4345 Answers

SOURCE: I need t replace the Air blend door actuator on my

This solution is not for a novice. Air flow doors are fragile and easy to damage.

Posted on Sep 07, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

  • 1 Answer

SOURCE: how do I remove the dash to replace blend door

blender door on a 2003 grand marquis blows only hot air the ac works

Posted on Apr 05, 2010

  • 248 Answers

SOURCE: What do I have to remove to access blend door actuator

very lenghty process. too long to describe here....go to Bonneville Forums read the text and follow linked there at the bottom....very good and detailed....I'm doing that right now,,,,it is a bugger,

Posted on Apr 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing blend door actuator on 2004 toyota 4runner


The actuator motor is on the passenger side, under glove box to the left. Pull it out and make sure the blend door moves freely, if not the dash must come out and the door be replaced or the new actuator will fail.

Jul 05, 2017 | Toyota Cars & Trucks

1 Answer

Small clicking sound when auto a/c is on


One of the actuators behind the dash. There are Mode Door, Blend Door and other actuators. You need to pinpoint which one it is. An auto shop should be able to do that for you.

Aug 27, 2016 | 2010 Toyota Tundra Grade 4.6L V8

1 Answer

Replace blend door in 07 Chrysler sebring


The most likely problem is either the blend door actuator or a broken blend door itself.
Both are only accessible by complete removal of the instrument panel(dash).
The blend door actuator can be tested with a Chrysler factory scan tool hooked up to the DLC(data link connector). If blend door actuator is working when tested with the factory scan tool, then blend door itself is at fault.
The only other way to test the blend door actuator is to test for 12v at connector, but you would have to remove the instrument panel in order to gain access to the actuator

Dec 24, 2014 | Chrysler Cars & Trucks

2 Answers

2006 buick lucern blowing hot air on one side and cold on the other side


Do you have dual zone cooling? If so, you have a bad air blend motor. I had to replace 3 on my 07 Impala and the basic geography of the part locations are the same for your Lucerne. There is one to the left of the radio well back into the dash, one to the right and one by the passenger side kick panel, near the door hinge. They are not for the faint of heart to replace. I had to replace mine because they were clicking and sounding obscene. They run about $25 each. Determine which is faulty using this rule of thumb:
Drivers side uncontrollable: replace far left blend motor
Passenger side uncontrollable: replace one just to the left of the glove box.
If you cannot switch between outside air and recirc, replace the one to the right of the glove box.
The blend control motors look eerily similar to a quartz clock movement you'd find in a hobby store, however, that is where the similarity ends.

Hope this helps

Jan 26, 2013 | 2006 Buick Lucerne CXL

1 Answer

2004 Toyota sienna blend door actuator intermittent problems


I know this post is old but for those of you experiencing this clicking noise it appears from my research so far that it is the actuator that moves the blend door. A couple of people even repaired the motor assembly because it appears to slip where the motor drive connects to the worm gear. If you search sienna ac actuator you can find the videos, I belive one guy was named Froggy. My passenger is stuck on cold and the driver side makes noise when moving to cold, the driver side also seems to hesitate going to warm. It's $120 for a replacement actuator. I'm really close to changing it, you just have to make sure the door and motor arm Match positions for it to work right. The dealer seems hesitant to replace it since they are worried it may be loose foam in the blender box. The box costs $3500 to replace though since its buried in the dash, and from what I've seen researching this the actuator is a possible issue in multiple models as well as Lexus vehicles and some other brands.

Jul 06, 2012 | 2004 Toyota Sienna

2 Answers

Hot air comes out the passenger side when air condirioning is on.


The control module or actuator is most likely the cause. You can manually set it for cold air until winter. Actuator is under the dash right by the blower.

Aug 20, 2009 | 2004 Chevrolet Silverado

3 Answers

01 silverado blend door changed /now works back wards!!!


most likely needs a LH (bottom) temp actuator. Located in the center of the dash on the bottom, you have to remove the hush panel on the rh side of the truck

Apr 24, 2009 | 2001 Chevrolet Silverado

2 Answers

Heat flowing on passenger side only


your actuatior foe the drivers blend door is stuck. try unhooking battery for a few minutes have both on heat and hook back up and start up. the actuators will run thru a learn mode and sometimes this will free up.if not you will need an actuator

Dec 09, 2008 | 2005 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...