Question about 2000 Dodge Grand Caravan

Open Question

2000 dodge grand caravan 3.3l has p1391 code replaced sensor

While driving the engine will miss but keep running could problem be bad flexplate connected to torqe converter

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: dodge caravan 1997 3.3l Xavierfrancofuenmayor

Had similar problems occur on various Chrysler products manufactured since 1986. What I did was remove the computer from the car and then take a Dremel tool with wire brush attachment and lightly buff all the pins of the computer--tops, sides and backs. After this I then take a jewelers round file and insert the tip into each connector pin hole and very lightly file it to remove any corrision. When I reassembling the connector plug to the computer I placed a good size dab of silicon grease on the plug in the center (acts as a seal when seated). This has eliminated the problem on four different vehicles.

Posted on Aug 28, 2008

  • 1 Answer

SOURCE: 2006 Dodge Grand Caravan - EGR code

I replaced the EGR Valve ($80 after tax), problem solved, vanruns great now. Now my problem is that I can't get the light to turn off.

Posted on Oct 06, 2008

  • 95 Answers

SOURCE: Replace the front wiper motor 2000 Grand Caravan Dodge

It is on the firewall under the hood. It has 3 to 4 bolts holding on. Be careful when taking it out to see how the new one lines back up. Hope it helps.

Posted on Mar 30, 2009

  • 14036 Answers

SOURCE: 2005 dodge grand caravan getting code p0406

3.3 engines has the egr valve with transducer.you have to replace the whole unit. code p0406 what its trying to tell you your egr valve circuit is short to ground.it has failed .

Posted on Jul 04, 2009

BCAS1298
  • 3092 Answers

SOURCE: P2097 Error code in 2006 Dodge Grand Caravan, which O2 Sensor?

The one before the catalytic, on the side where cylinder # 1 is at. close to the exhaust mag.

Posted on Dec 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the problem when engine code P1391 keeps coming up?2000 Dodge Dakota Sport 3.9 liter engine 4x4 replaced lot of parts no satisfaction


Codes starting with P1xxx are manufacturer specific codes. Repost your question and indicate the make, model, year and engine in your vehicle, and someone familiar with your brand may be able to help.

Apr 10, 2017 | Cars & Trucks

1 Answer

My car reading the following codesp1489 codep0601 p0725 p1490 p1391 p0700 p 0703,car cut off while driving oil seems to be thin smells a Lil like gas was told its a sensor but not which one Let me know any...


If the oil smells like gas , pull the dip stick an put a lighter to it ! If it catches fire there is gas in the oil ! you don't won't to drive the car it could explode ! .
P1391 is for camshaft position sensor and crankshaft position sensor. the code is for either sensor or both

Read more: http://engine-codes.com/qa/4492/p1391-dodge#ixzz3TS85EkNt
P1489 Dodge - High Speed Radiator Fan Control Relay Condition

Read more: http://engine-codes.com/p1489_dodge.html#ixzz3TS8ycHqw
P1490 Dodge - Low Speed Radiator Fan Control Relay Condition

Read more: http://engine-
codes.com/p1490_dodge.html#ixzz3TS9QKO2x

P0725 Dodge - Engine Speed Sensor Circuit
P0700 Dodge - Transaxle Control System Malfunction
P0703 Dodge - Brake Switch Performance Repair Importance Level: 3/3 Repair Difficulty Level: 2/3 help.jpg pdf.gif share.png 2 0 comments.png ' Add Comment xicon.jpg http://engine-codes.com/p0703_dodge.html Forum Code Possible causes - Faulty Brake Switch
- Misadjusted Brake Switch
- Brake Switch harness is open or shorted
- Brake Switch circuit poor electrical connection

Read more: http://engine-codes.com/p0703_dodge.html#ixzz3TSAXHIBZ
With all these codes present , without looking under the hood , I would think you have a wiring harness problem ! I have seen critters make nests in the engine compartment , they like to chew wiring ! Have seen air filter boxes full of dog food . Good luck your going to need it !

Mar 04, 2015 | Dodge Cars & Trucks

1 Answer

Keep getting code p1391


You may need a shop manual for this one.
Code 1391 means the crank sensor or cam sensor signal is not steady or dead at times.
The distributor acts as the cam sensor, so it could be that or the crank sensor, or a problem with the wiring harness.

Feb 18, 2014 | Chrysler Cars & Trucks

1 Answer

What Is This Error Code P1391 Mean


I have done some research and found my shop manual for a Pacifica doesn't show a code P1391. I found it at another web site it's a crankshaft or cam sensor. What I found is if the car is running somewhat smooth replace the crank sensor if it is shaking when you accelerate there is a good chance your flexplate(flywheel) is cracked or broken.

Dec 07, 2011 | Chrysler Cars & Trucks

1 Answer

2000 dodge stratus 2.5 with code p1391


DTC P1391 fault code is a loss of cam or crank signal to the eng computer; the most common problem is the crank (CKP) sensor goes bad.

Find the crank sensor connector, you'll see the sensor mounted to the bellhousing, it goes down into the housing and reads off the flexplate. When it acts up, unplug the connector. Check the voltage on the yellow wire, it should have 8v. Plug the sensor back in and recheck the voltage. If it drops out replace the sensor. Check for ground on the black/green wire. If this and the 8v are ok, put a paperclip into the backside of the connector on the third wire in the connector and contact the terminal. Put one voltmeter lead there, the other lead on chassis ground. turn the engine over slowly by hand and the voltage should toggle from 0-5v. If it doesn't, replace the sensor.

If sensors are new and wiring is good, you are looking at a computer failure. Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using FixYa.

Jose.

Oct 19, 2011 | 2000 Dodge Stratus

1 Answer

I have a 2001 Jeep Grand Cherokee and my check engine light is on. Took it to "Advance Auto Parts" and got the code P1391. What is this?


could be a crank or cam sensor beginning to fail, or a bad harness connection at either. Usually though you would feel a problem there as both are necessary to keep the engine running.

Oct 12, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Fault code indicating the cam sensor on a 2000 3.0 dodge grand caravan . did replace the distibuter at the same time as the computer showed it was a bad fault code at first


It's probably the z1 ground from the fuse box out to the engine.It runs under the battery which corrodes it bad & causes many other shorts.Since it runs, I need a little more info.

Jun 20, 2009 | 2000 Dodge Caravan

Not finding what you are looking for?
2000 Dodge Grand Caravan Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...