Question about 2008 Dodge Durango

Open Question

ESP, BAS and Brake lights on dash on dodge durango 2008

My ESP, BAS, and Brake lights are always on in my dash

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
wracefans24
  • 1985 Answers

SOURCE: ABS and ESP BAS is turned on and the fault

C1041 code is-Left Front Tone Wheel Performance
the speed sensor was slower then the other front one to react to something,or the left wheel spun and not the right front one,
or there is a problem in the sensor or wiring

Posted on Nov 22, 2009

Ad
tneubauer
  • 437 Answers

SOURCE: my esp/bas light and the red airbag and abs lights

ESP = Electronic Stability Program
BAS = Brake Assist System

Posted on Jan 13, 2010

kapishtech
  • 2272 Answers

SOURCE: the ESP/BAS light keeps coming

Have you unhooked your battery for something? You might try making sure the stability control's steering sensor is correct...

Basically, start the car turn the wheel all the way left to the stop, all the way right, then back to center. This lets the stability control know where "center" is.
Try this:
1) Disconnect your battery, wait 1 minute & just turn on the lights for a second as to remove any residual current from the computer.The lights will not come on but still turn ON.
2) Re-connect the battery, this should have cleared all of the lights except for the ESP\BAS light.
3) Start the car, center the wheels, turn all the way to the left then all the way to the right. This should clear the ESP\BAS light.
------- If still the same problem then the esp/bas module needs to be checked and reprogrammed by the dealer to turn it off. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation

Posted on Sep 04, 2010

tunde007
  • 2382 Answers

SOURCE: ESP/BAS warning light on. went

Hi, these systems are all linked together. Most commonly, one of the wheel speed sensors is not reading or is reading incorrectly. This can also occur on slippery surfaces where one or more wheel slides enough to cause the sensor to drop the signal, but not enough to meet criteria for an abs or esp episode. If the light comes back every time you turn on the ignition, there is a deeper problem.
The system has detected a fault in the electronic stability program - brake assist system. You have an electrical connection at the rear wheels secured to the inside of the brake area and are viewable from under the vehicle. It is a small wire harness running to each wheel. Grab the connector and wiggle it around, and make sure they are tight. Due to the connector being mounted low to the ground, sometimes they become dirty or corroded, not making contact. Do this on both sides and see if the lights turn off.

If the light does not turn off, you have to replace dynamics sensor, which is mounted UNDERNEATH the center console in the car. There is a "lost communication to dynamics sensor" and "low voltage to dynamics sensor supply"..

Posted on Feb 13, 2011

  • 1 Answer

SOURCE: 2008 Dodge Charger The esp/bas

CALL ME AT 716 896 5530 I HAVE A TOTAL SOLUTION GLENN

Posted on Aug 11, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My dodge journey esp bas light turns on , what does it mean ?


This is an ESP / BAS Trouble Indicator symbol, meaning Electronic Stability Program and Brake Assist System ().These systems work together, and a fault in either or both will cause the light to come on. Have it checked out just go to your local auto supply store like Auto Zone are Advance auto they have a hand held devise that can check it out at no cost. :-)

Apr 15, 2018 | Dodge Journey Cars & Trucks

1 Answer

2009 Durango multiple lights on dash . ABS, Brake, ESP/BAS, etc. Dealer says harness is bad. When lights go out on dash, vehicle runs fine. Dealer says splice S119 is bad. How do I find that splice?


Normally you would look it up in the factory service repair manual .The manuals you buy at the parts store do not show this info. You can go to the factory web side OEM One Stop TechInfo go here ,click dodge ,click on line subscriptions , for $24.95 you can have info you would never thought existed. for one day .

Sep 09, 2017 | Cars & Trucks

1 Answer

The esp bas light is on my 2009 dodge 1500 and it won't start


An Electronic Stability Program (ESP)/Brake Assist System (BAS) indicator is standard equipment on all instrument clusters. The ESP/BAS indicator is serviced as a unit with the instrument cluster.
The ESP/BAS indicator gives an indication to the vehicle operator when the Electronic Stability Program (ESP)/Brake Assist System (BAS) has been activated. This indicator is controlled by a transistor on the instrument cluster circuit board based upon cluster programming and electronic messages received by the cluster from the Controller Antilock Brake (CAB) and the Transmission Control Module (TCM) over the Controller Area Network (CAN) data bus.
The ESP/BAS indicator Light Emitting Diode (LED) is completely controlled by the instrument cluster logic circuit, and that logic will only allow this indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the LED will always be OFF when the ignition switch is in any position except ON or START. The LED only illuminates when it is provided a path to ground by the instrument cluster transistor. The instrument cluster will turn ON the ESP/BAS indicator for the following reasons:
  1. Bulb Test- Each time the ignition switch is turned to the ON position the ESP/BAS indicator is illuminated for about four seconds as a bulb test.
  2. ESP/BAS Indicator Lamp-On Message- Each time the cluster receives an electronic ESP/BAS indicator lamp-ON message from the CAB indicating that the ESP/BAS system has been activated, the ESP/BAS indicator will be illuminated. The indicator remains illuminated until the cluster receives a lamp-OFF message from the CAB, or until the ignition switch is turned to the OFF position, whichever occurs first.
  3. ESP Full Off Textual Message- Each time the cluster receives an electronic ESP Full OFF indicator lamp-ON message from the CAB indicating that the ESP/BAS system has been manually disabled, an ESP OFF textual message will appear within the cluster odometer display. The ESP OFF textual message remains displayed until the cluster receives a lamp-OFF message from the CAB, or until the ignition switch is turned to the OFF position, whichever occurs first.
  4. Actuator Test- Each time the cluster is put through the actuator test, the ESP/BAS indicator will be turned ON, then OFF again during the bulb check portion of the test to confirm the functionality of the LED and the cluster control circuitry.
The CAB continually monitors the ESP/BAS circuits and sensors to decide whether the system is in good operating condition and the proper outputs to the components of the system. The CAB then sends the proper lamp-ON or lamp-OFF message to the Electro Mechanical Instrument Cluster (EMIC) (also known as the Cab Compartment Node/CCN).
For proper diagnosis of the ESP/BAS system, the CAB, the TCM, the EMIC, the CAN data bus or the electronic communication related to the ESP/BAS indicator operation a diagnostic scan tool is required. Refer to the appropriate diagnostic information.

Apr 11, 2016 | Dodge Cars & Trucks

1 Answer

The esp bas, abs, traction & brake light come on when I drive


take it to a mechanic! the drive train is failing

Jun 09, 2015 | 2008 Dodge Grand Caravan

3 Answers

2007 dodge durangos brake light came on then the brake pedal got really hard to press so i replaced the whole braking system and it was good for 2 days now the brake is hard esp bas brake lights on


If your truck has a brake booster, I suspect the vacuum hose to the booster has gotten fuel into it or just gotten old and is collapsing inside.

Apr 27, 2015 | 2007 Dodge Durango

1 Answer

2008 dodge charger ESP/BAS and traction light on


Have the brakes inspected for worn out brake pads causing a metal to metal scrape of the pad and brake rotor.

Mar 20, 2014 | Dodge Charger Cars & Trucks

2 Answers

BAS/ ESP light on the dash bord stays on all time the car engine is running


The BAS stands for Brake Assist System, don't remember what ESP stands for.
But the first thing to do is make sure the brake lights go on when you hit the pedal.
If not, then replace the brake light switch above the pedal.
If that is not it, it could be many things, such as a bad lateral acceleration switch.

Feb 03, 2011 | 2001 Mercedes-Benz E-Class

1 Answer

What does 'BAS ESP' mean? its come up on my dash-board on my car


Brake Assist System, Electronic Stability Programme. It will need to go on a computer, the most obvious thing is the brake light switch, fault will need to be erased after fixed.

Jul 13, 2009 | 2008 Mercedes-Benz Mercedes Benz C Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...