Question about Cars & Trucks

Open Question

Vacum hose diagram 99 chrysler sebring convertible

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Intimowdater
  • 1 Answer

SOURCE: Chrysler Sebring Problem

along the buttom of the rocker pannel there is a seam that gets bent from jacking in the wrong place ,that seam is where the drains are,screw driver and pry apart at the drain ,the drain is a tube shaped bump molded in the steel on the inside part of rocker panel

Posted on Oct 26, 2008

Ad
  • 50 Answers

SOURCE: 2000 chrysler sebring convertable top will go down but will not

Typically, when when this happens, the system is low on fluid and/or must be bled. Here are the procedures:
Lower the top to the full down position.

  1. Remove the rear seat cushion, seat back and inner quarter trim panels. Pull up sharply on the seat cushion at the front about midway between the middle of the seat and the outside edges. The seat back is held in by nuts. The quarter trim panels are held in by screws I think.
  2. Remove the cylinder mounting brackets and remove the cylinders from the trunnion pivot mounts.
  3. Rotate the cylinders 180 degrees (the hose fittings will now face to front of the vehicle.
  4. Disconnect the motor/pump retaining clips from the body.
  5. Rotate and raise the motor/pump assembly so the reservoir is in the up position. The rubber filler plug will be at the top.
  6. Raise motor/pump fitting to at least 2 inches above the horizontal rear seat back reinforcement.
  7. Tilt the motor/pump assembly to approximately the 10 o'clock position, with the rubber filler plug still at the top CAUTION: THE MOTOR/PUMP ASSEMBLY MUST REMAIN IN THE CURRENT POSITION UNTIL THE RUBBER FILLER PLUG IS REINSTALLED IN THE Step 12.
  8. Remove the rubber fill plug from reservoir.
  9. Fill the hydraulic system by adding Dexron 2 Automatic Transmission Fluid to the bottom of the fill hole CAUTION: DO NOT OPERATE THE TOP SWITCH IN THE UP (CLOSING THE TOP) DIRECTION.
  10. With two people, activate the top switch in the down (opening the top) position to fully retract the cylinder rods and hold for approximately 5 seconds, until the motor/pump stalls. A percolating or gurgle sound/feeling is an indication that the procedure is working.
  11. Top off the motor/pump with Dexron 2 and insert the filler plug.
  12. Install the motor/pump assembly into the vehicle mounting bracket.
  13. Rotate the cylinders back to the original position (hose fitting rearward)
  14. Install the motor/pump lead and hydraulic line clips (the hydraulic line clips are to assist in the production process) to ensure that the seat back/seat cushion do not pinch the lines. If the sticky side is no longer holding to the floor pan, the clips can be left off.
  15. Ensure that the bushing is still on the trunnion pivot mount and bracket. Tap the top switch in (raising the top) to get the cylinder trunnion onto the trunnion pivot mounts, if needed.
  16. Install cylinder mounting brackets.
  17. Raise and lower the top to ensure proper operation.
  18. Install the inner quarter panels, and the rear seat back and cushion.
  19. And Just a fair warning here - you WILL spill fluid inside your car. If you manage not to, I want to know how. I cover everything with garbage bags because there have been a few instances where I accidentally hit the button the wrong way and that stuff went EVERYWHERE. Be careful and good luck.

Posted on Apr 17, 2009

  • 538 Answers

SOURCE: 2007 chrysler sebring serpentine belt diagram

Go to; daycoproducts.com, click cars and trucks, then go to serpentine belt. Then on the right side of the screen click on finding your vehicle. Then get the illistration number and click on illistrations, go to that number it should something 6-? or 7-?. It's a pretty good websight.

Posted on Jan 31, 2010

  • 1757 Answers

SOURCE: I need a timing belt diagram for a 2005 chrysler sebring

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
http://www.2carpros.com/car_repair_information/year/2005/make/chrysler/model/sebring/2005_chrysler_sebring_timing_belt_diagram_marks.htm

Posted on Mar 08, 2010

joshnaz
  • 186 Answers

SOURCE: whats the deck light mean on a 1998 chrysler

Your deck light is the rear trunk lid light.

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Belt diagram routing


go to www.automecanico.com translate this web with your browser
and get the topic.
God bless you

Jul 29, 2013 | 2008 Chrysler Sebring Convertible

2 Answers

LOOKING FOR SOME IDEAS IF ANYONE CAN HELP WITH ( 96 CHRYSLER SEBRING CRANK SENSOR STUCK IN TRANS. WANT TO REMOVE IT WITHOUT HAVING TO REMOVE TRANSLOOKING FOR SOME IDEAS ANYONE THANKS


Clean it up and spray it with some solvent and let it soak...the o-ring is probably melted..you can also tap it with a rubber mallet to free it up. Of course, the retainer bolt has to be removed.
I hope this helps.

Jul 21, 2011 | 1996 Chrysler Sebring

2 Answers

Cannot locate the thermostat on a 2003 chrysler sebring convertible with the dohc v6


I BELIVED IN LOWER RADIATOR HOSE IS WHER YOU WILL FIND IT AT THE ENGINE END
OF COURSE MAY REQUIRE SPECIAL EQUIPMENT TO REFILL MOST UNIT ARE NOW VACUMED FILLED

Apr 16, 2011 | 2003 Chrysler Sebring

1 Answer

LOCATION OF #5 INJECTOR ON 2000 SEBRING JS CONVERTABLE i CAN NOT LOCATE A DIAGRAM ANYWHERE


2000 Chrysler Sebring Convertible 3.0 liter SOHC V-6 VIN "H"

e1d33f3.gif


Hope this helps (remember to rate this).

Oct 28, 2010 | Chrysler Sebring Cars & Trucks

2 Answers

Tire specs for 2001 chrysler sebring


HI. Here is the complete line up of specs concerning your vehicles front and rear tires. You did not post the trim line of this car, so I posted all models and tire combination's specified by the manufacture.


2001 Chrysler Sebring Lim 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Coupe Front and Rear Tires P205/55R16
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Coupe Front and Rear Tires P215/50R17
2001 Chrysler Sebring LXi 4 Door Sedan Front and Rear Tires P205/60R16

Jul 06, 2010 | 2001 Chrysler Sebring

1 Answer

2005 Sebring Convert Radio/light off


I am having this same problem with my 99 sebring.. anyone know what we can do to fix this?

Oct 21, 2008 | 2005 Chrysler Sebring Conv

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...