Question about 2009 Dodge Journey

Open Question

Diagram of serpentine belt for a 2009 dodge journey

Need a diagram on how the serpentine belt goes on

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: serpentine belt diagram:

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Posted on Jul 18, 2008

  • 3 Answers

SOURCE: need diagram for 2000 dodge dakota serpentine belt

On the 1999 Dakota with the 3.9liter, the fan shroud absolutely DOES NOT have to be removed. Very simple job. Simply use a breaker bar with a 15mm socket on the belt tesioner pulley nut. Using the breaker bar push (as though tightening) the pulley nut...the reaction will be that the tensioner removes tension from the pulley and the entire belt can be removed by easily slipping it toward the front of the vehicle...comes right off. The new belt can go back on in exactly the same manner. By the way the belt routing diagram IS CONVIENENTLY LOCATED between the hood latch and the radiator mounting for simple and quick refernce...one person job, I did removal and installation four times in less than 10 minutes. (why four times? The auto parts store was selling replacement belts that were too long and did not allow the belt tensioner to provide suffiecient tension...I had to try four different manufacturers before the tensioner was adequately tight with room to grow as the belt naturally stretches from use.). I found no stringing around the fan is required because of the way the belt is routed (it doglegs around the main engine pulley which is centered below the fanhousing and then the belt runs from there to the left side of the fan housing...avoiding the fan/fanhousing all-together (sure you can try to go past the fan/fan housing if you so desire...but you dont have to...and besides the space between the pulleys and the fan is ample to allow the belt to pass between with minimal interference or a simple rotation of the fan as you attempt this method. One hint that made my installs easy as pie...the last pulley you put it over should not be a bezeled and ridged pulley or you will needlessly make life difficult for yourself...the last pulley should be the water pump pulley which is a smooth bore and non-ridged pulley (makes you wonder how the belt even stays on it!)...making it easy as pie to slip it right over...as your last act of defiance to that mean old serpentine belt!

Posted on Jan 17, 2009

BCally1
  • 133 Answers

SOURCE: replacing serpentine belt for dodge ram 3500 diesel

5.9L DIESEL
196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :

  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.


196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Posted on Jan 22, 2009

  • 1757 Answers

SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan

3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Jan 22, 2010

  • 1757 Answers

SOURCE: need diagram for serpentine belt for dodge caravan 1991 free online

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
For the 1991 Dodge Grand Caravan:
http://www.2carpros.com/car_repair_information/year/1991/make/dodge/model/grand_caravan/1991_dodge_grand_caravan_drive_belt_routing_diagram.htm

Posted on Mar 07, 2010

Testimonial: "thanks for your help it was along time ago and forgot to let you know thank you so much "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2009 dodge journey serpentine belt routing diagram to replace the belt the belt is good just got to get thin on my wife is handicap and i never know when i need to carry her to hospital


Belt replacement specs of all or most cars are on top of the radiator, somewhere in the vicinity or even on the inside of hood when you lift it or a pic on the frame, look for a lil pic, if you cannot see one call a junk yard in your area or the dealership and have them copy it out of the owners manual and email it to you or even a parts store hope that helps ya

Jan 02, 2015 | 2009 Dodge Journey

1 Answer

Fuses diagram


If you need 2009 dodge journey fuse box diagram and fuse box details,then please click the link below and view the diagram:-----
http://www.gresk.com/2013/09/dodge-journey-fuse-box-diagram.html
------------
This will help.
Thanks.

Sep 29, 2013 | 2009 Dodge Journey

1 Answer

2009 dodge journey belt routing


go to your local parts store in their belts and hoses catalog there are belt routing diagrams have them make a copy for you on your vehicle

Jun 05, 2012 | 2009 Dodge Journey

1 Answer

Serpentine belt diagram


it the pulley has ridges an/or lips the ridge(s) side of the belt goes around it. if the pulley is smoth then the back side of the belt goes around it. You shouldnt need a diagram.

Jul 07, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

Serpentine belt diagram:


The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Jun 27, 2008 | 1993 Dodge Caravan

Not finding what you are looking for?
2009 Dodge Journey Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...