Question about 2004 Mercury Montery

Open Question

P2004 engine code 2005 merc monterey - 2004 Mercury Montery

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 194 Answers

SOURCE: 2005 Mercury Monterey with check engine code

P0128 is Coolant Thermostat ( Coolant Temp Below Thermostat Regulating Temperature ). The thermostat may be stuck open, preventing normal operating Temperature from beeing reached.How is the heat inside the car is it below normal ? Or the engine Coolant Temperature Sensor may be faulty and needs to be replaced. Good Luck and have a good XMASS.

Posted on Dec 17, 2010

  • 869 Answers

SOURCE: 2005 Mercury Monterey with check

it is an error showing some issue with thermostat.

Posted on Dec 28, 2010

tunde007
  • 2382 Answers

SOURCE: can't get brakes to bleed

Hi, did you follow the due process of bleeding the car brake? Maybe i should give you the proper guideline on how to bleed the brake which is below....

Fill the master cylinder with brake fluid before beginning. Jack the car up so that the two rear wheels are about six inches above the ground. Slide under the right rear wheel and look at the back of the brake system for a small bleed valve. A bleed valve is a hollow bolt. When loosened it will allow the brake fluid to flow out and result in the vehicle having no brakes.

Fit a rubber hose over the end of the bleed valve. Make sure it forms a tight seal and make sure the free end is below the level of fresh and clean brake fluid. As the brake fluid in the line pushes out of the system, you will see a bubble come from the end that is under fluid.

Have a helper sit in the driver's seat and follow your instructions. Tell your helper to pump the brakes hard a few times. Open the bleeder valve and tell your helper to press the brake pedal firmly down to the floor and hold it there until you indicate otherwise. Close the bleeder valve and have your helper release the brake pedal.

Repeat this process until you see a small bubble ejected from the tubing under the surface of the brake fluid in the jar. Once you have finished with this wheel, move to the left rear wheel. Before you begin the next wheel brake, refill the master cylinder reservoir. Get set up and repeat the same steps for this tire. The next two wheels you will bleed are the right front wheel and then the left front wheel.

Bleed the wheels in the order of the longest brake line first and then working towards the shortest brake line. Refill the master cylinder reservoir before beginning each new wheel. Once the rear brakes are finished, lower the car and jack up the front of the car. Remember to road test the brakes and make sure they operate well.

If you cannot still bleed the brake, then you need to get in touch with an Auto Mechanic to do the job....

Posted on Feb 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix code p2004 on 2005 ford focus


you code is here

P2004 Ford Intake Manifold Runner Control Stuck Open Bank 1


Possible causes - Intake Manifold Runner Control (IMRC) monitor signal shorted to power
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Intake Manifold Runner Control (IMRC) solenoid
- Damage Powertrain Control Module (PCM)
- Blocked vacuum hoses
alt="What does this mean?"> What does this mean? Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P2004 Ford Description The P2004 is set when the Intake Manifold Runner Control (IMRC) is commanded closed by the Powertrain Control Module (PCM), but the IMRC indicates open.


Read more: http://engine-codes.com/p2004_ford.html#ixzz3lke1SreV

Sep 14, 2015 | Ford Cars & Trucks

1 Answer

I have a 2005 mercury Monterey van with a check engine light on. Autozone diagnosed either a mass air flow sensor or O2 sensor problem. I tried cleaning the air flow sensor with air flow sensor cleaner but...


If it is running lean, I'd check correct fuel pressure. Then check for a vacuum leak. 02 sensors are part of a tune-up. I don't like to replace parts unless I'm sure.

I can't rule out a maf sensor.

Jul 29, 2014 | 2005 Mercury Monterey

1 Answer

Why is my 2007 jeep compass codes p2004 and p2017?


both jeep factory codes.
which engine, we cant guess engines ever. here.
alldata.com covers it
the FSM factory serv. manual.
and google findes endless hits, ever use google ? why not?
ill type it for u now.;...
https://www.google.com.pe/webhp?gws_rd=cr,ssl&ei=meaWVNDcI6fGsQT5oIGgCA#q=p2004+and+p2017+dtc



Jul 16, 2014 | 2007 Jeep Compass Limited

1 Answer

Keep getting a p2004 code what does this mean?


Just go to google and put in p2004 code. It will give you alot of great info and even videos to show you how to fix it yourself.

Jun 22, 2014 | 2005 Ford Freestar

2 Answers

Where are the fuse boxes located a 2004 mercury monterey?


I know there are at least two. The first being under the dash to the left. Second being in engine bay above the driver side tire.

BIll

May 29, 2014 | 2005 Mercury Monterey

1 Answer

P2004 intake valve stuck open


code p2004 refers to intake manifold air control actuator-bank 1--actuator stuck open===Causes---wiring--intake manifold air control actuator---mechanical fault .I would check blockage and wire connections Then I would replace the actuator But I would not tear down the engine as it is between the air filter and the manifold. Check the air cleaner element

Apr 27, 2013 | 2005 Ford Expedition

2 Answers

Cruise control on 2005 mercury monterey quit,which fuse,the manual doesn't say.


IF ANYONE IS WILLING TO ASSIST WITH A FREE ANSWER FOR 04-05 MERC. MONTEREY MINIVAN CRUISE CONTROLL STOPPED WORKING , ( fuse is ok) IT WOULD BE SO APPRECIATED. MY EMAIL IS. generaljoe67@verizon.net.

Aug 24, 2011 | Mercury Monterey Cars & Trucks

1 Answer

2005 Mercury Monterey with check engine code P0128; what does it mean?


P0128 is Coolant Thermostat ( Coolant Temp Below Thermostat Regulating Temperature ). The thermostat may be stuck open, preventing normal operating Temperature from beeing reached.How is the heat inside the car is it below normal ? Or the engine Coolant Temperature Sensor may be faulty and needs to be replaced. Good Luck and have a good XMASS.

Dec 17, 2010 | 2005 Mercury Monterey

Not finding what you are looking for?
2004 Mercury Montery Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...